Cisco Firewall :: How To Configure Multiple Static IPs On ASA 5505
Jun 10, 2011
I am setting up a Cisco ASA 5505 first time for My organisation, I usually setup Cisco Router, I have 10 Static IP, & Have 6 Server (S-1, S-2, S-3, S-4, S-5, S-6), Traffic Should be pass through the ASA and is distributed to the destination server that is specified in the packet. LAN servers can be separated into discrete networks for security. For example, a private LAN for internal traffic accessed only via remote dial-in VPN sessions and Want to Configure DMZ for Server (S-4, S-5, S-6) that allows public web traffic.
I have Attached My Network Diagram I have some question,
1:- Can we Configure Multiple Static IP On ASA 5505 ?
2:- If Diagram is wrong what change need to be done ?
View 2 Replies
ADVERTISEMENT
Dec 23, 2011
I want to configure multiple DHCP pool on ASA. that I create like
int e0/2
no shut
interface Ethernet0/2.10vlan 10nameif inside10security-level 100ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2.20vlan 20 nameif inside20 security-level 100ip address 192.168.20.1 255.255.255.0
dhcpd address 192.168.10.10-192.168.10.254 inside10dhcpd dns x.x.x.x y.y.y.y interface inside10dhcpd enable inside10
dhcpd address 192.168.20.10-192.168.20.254 inside20dhcpd dns h.h.h.h z.z.z.z interface inside20dhcpd enable inside20
I have following query...
1. int e0/2 work as trunk port, is it? any special confiduration require other than dot1Q?
2. How can I configure inside interface? is it like,
access-group inside_access_in_1 in interface inside10
access-group inside_access_in_1 in interface inside10
3. How can I configure static NAT ?
4. How can i configured inside route?
5. How can I configured default NATing?
6. On which interface I access ASA? currently using inside interface.
View 5 Replies
View Related
Jan 10, 2012
I am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies
View Related
Mar 12, 2012
We have a need for an inside address to have more than one static NAT outside addresses. I know this wasn't possible before 8.3.X code. I still can't quite get it to work with 8.4.X code yet.
Here is what I had with 8.2 code.
static (inside,outside) 10.21.197.0 10.17.197.0 netmask 255.255.255.0
our inside network is 10.17.197.X/24. the current NAT we have in place is 10.21.197.X/24.
we need to add an additional NAT of 10.22.197.X/24 and I also have networks that will need to hit the address with no NAT.
I do know the source networks where I need each of the three cases:
from 172.20.X.X I need to hit the inside of 10.17.197.X natively, no NAT.
from 192.168.X.X i need to hit the inside of 10.17.197.X with 10.21.197.X NAT
from 10.10.X.X I need to hit the inside of 10.17.197.X with 10.22.197.X NAT
View 2 Replies
View Related
Feb 24, 2012
I need to replace an ASA with an IOS firewall router, and am not sure how to migrate the NAT configuration. Specifically, there is an interface "3rdparty" that has onward connectivity to other private addresses, so our internal addressing is hidden. For some reason there are static NAT rules in different directions across the interface, but at present I cannot see why. Thinking in router terms, all that springs to mind is the inside and outside tags for the interfaces, but also that it might need "overlapping" NAT to be configured.
[code]...
View 2 Replies
View Related
Aug 15, 2011
I am at a loss on configuring a new ASA5505 for multiple static port translations.I would have expected to simply add several service command to a network object to complete the task, however, the service command overrides the previous and replaces rather than adds to the translations. [code] However, if entered in that order the 8443 overwrites the 8080 static translation.What is the correct procedure to establish multiple translations? If someone could also provide the "old" style for pre 8.2 release, I'd like to compare because I thought I used to do this with an access-list somewhere.
View 4 Replies
View Related
May 15, 2013
I am trying to set up my ASA5510 the fail over of ISP when it can't ping three different IP. I create three different tracking to three different IP using sla monitor & track rtr. But when I do
route isp2 0 0 yy.yy.yy.yy 50
route isp1 0 0 xx.xx.xx.xx 31 track 1
route isp1 0 0 xx.xx.xx.xx 32 track 2
route isp1 0 0 xx.xx.xx.xx 33 track 3
the last route will replace the previous two and only the last route command takes effect.Is there anyway I can set up the fail over to ISP2 only when it can't ping three different IP from ISP1?
View 1 Replies
View Related
May 26, 2011
I just replaced a PIX 501 with a new ASA5505. I had a very weird problem and would like to know what caused it incase I run into it again. The setup is a DSL connection, with an old-ish speedstream DSL modem. Static IP, no PPPoE. I had a PIX 501, then two servers with static NAT entries on secondary WAN IPs. Everything was working fine on the PIX, I just duplicated the config over to the ASA. I swapped out the PIX for the ASA, and rebooted the DSL modem to clear out it's cache. After installation, NAT was working fine for the the global pool, but the systems with static NAT could not get online. I tried lots of different things to fix them, and they never worked. Finally I rememberd running into an issue like this a long time ago, in that the static NAT IP's wouldn't work without giving them a bump-start on the network. So I assigned the ASA each of my WAN IPs, one at a time, and tested them all. After that I went back to the original WAN IP, configured the static NATs, and they fired right up. why did my static NAT entries not work until I first assigned them to the ASA, then swapped back? I did reset the DSL modem when I swapped the firewalls, so I don't believe it was an ARP issue (unless it was an ARP issue at the far end?) I would like to know if there is something I can do differently with the devices or with the config to not have this issue again in the future.
View 5 Replies
View Related
Sep 23, 2011
I have a Pix 501 running 6.3 code sitting behind a cable modem. I use ip address outside dhcp setroute because I don't have a dedicated IP from my cable provider.
How do I configure the Pix to host VPN connections from my iPad when offsite? Since the outside interface is going to change, I can't configure a static IP.
View 1 Replies
View Related
May 25, 2011
Currently a customer has all theLAN devices using a router as the Default Gateway. The router also do the Dynamic NAT to the internet access and has NAT/PAT rules to publish some services like HTTP and FTP. As I know the router will permit all the incoming traffic in all its interfaces without restrictions at less there is an ACLs that restrict the incoming traffic on an specific interface.Now the customer has bought a brand new ASA and wants to use it as the default gateway for the entiery LAN. This means, the ASA will have the internet connection and will be the responsible for the NAT/PAT process.
I have configured the NAT/PAT rules already following the current router configuration, but I need to know if I have to configure ACLs allowing the incoming traffic on th Outside interface for the services I NATed.
View 1 Replies
View Related
Jan 12, 2012
I have a Cisco ASA5505 running 8.2(1) and I am using ASDM to manage the firewall. I have a Linux VPN server on the inside with and IP address of YYY.YYY.YYY.39 with a static NAT to the outside with an address of XXX.XXX.XXX.171 . I have a site to site VPN tunnel which terminates on the outside of the ASA on the outside interface XXX.XXX.XXX.190 .Traffic from the YYY.YYY.YYY.0/24 network can't transverse the site to site VPN as there is a conflict of IP address's on the far side so it is natted via a dynamic policy to host address ZZZ.ZZZ.ZZZ.100, Users remote into the inside(YYY.YYY.YYY.0/24) for support via the Linux VPN server (.39) and then need to communicate down the site to site VPN. The problem is that the static NAT for the incomming connections takes preference and bypasses the site to site VPN tunnel for outbound traffic. I tried to create a policy Static nat but it tries to modify the static nat that handels the incomming traffic to the Linux server.
View 2 Replies
View Related
Jan 28, 2013
i have 2 internal server sitting in inside interface
inside network vlan 1 ip address 192.168.0.20, and 192.168.0.22
i going to map 192.168.0.20 to public ip routable address 203.117.124.180 and 192.168.0.22 to public ip routable address 203.117.124.181
the purpose is to make those 2 server 192.168.0.20, and .22 to be able to access remotely using public routable ip address,
however, after done the configuration i still not able to ping or access the public IP Address mention above. my both server are turn on and can access internally.both server are also able to access internet. See below partial configuration retrieve from Show Run.
nat-control
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
nat (Antlab) 1 0.0.0.0 0.0.0.0
[Code].....
View 2 Replies
View Related
Aug 30, 2011
I have a 5505 for a small business that has one web server. The web server has a static NAT entry to an IP address and not an interface. There is an access rule allowing any HTTP traffic to the outside IP of the web server. From the web server I can't access the Internet.
All other computers on the network can access the Internet using a dynamic nat rule that uses the outside interface. The web server is accessible from a computer behind the firewall.
If I delete the static NAT entry for the web server I can get on the Internet.
I have turned debugging on and see that an outbound connection is built and then 30 seconds later the connection is torn down with the bytes 0 SYN Timeout message.
I am running 8.0(5).
View 3 Replies
View Related
Aug 31, 2012
I have an ASA 5505 behind my internet router. i have got only one public ip configured on the router outside interface.192.168.20.0/24 subnet is configured between ASA and router and inside network is 192.168.10.0/24 (Refer the attached diagram).
I have exposed my mail server and ftp server to public through static PAT in router and ASA with the same public on router outside interface. Iam facing issue some of the machines inside my network internet is not working(actually DNS is not resolving) some of the PC's internet is working fine some of the PC's randomly working. i have attached the diagram and ASA config , after this issue is sorted out i need to configure a L2L VPN to my head office.
View 8 Replies
View Related
Feb 5, 2012
I'm trying to configure a second server on my network but whenever I add the static NAT rule, the internet stops working on that computer.
Here's my Cisco ASA configuration:
ASA Version 7.2(3)
!
hostname domain
[Code].....
View 16 Replies
View Related
Feb 9, 2013
I have configured the ASA in a very similar manner to how the PIX was set up but I'm having trouble with some hosts on the inside accessing the Internet. Any inside hosts which use DHCP work fine. Any inside hosts with a static IP (and configured on the ASA with a "static" rule) cannot access the Internet. For example, in the config below the server daviker-dialler cannot access the Internet. I've spent a few days working on this now and have started from scratch several times but I'm not getting anywhere. Apologies for all the X's everywhere, didn't like to post anything sensitive on the Internet.
View 2 Replies
View Related
Jun 3, 2013
I am mapping static ip address to the local ip address.We have a bsnl broadband connection, and bsnl has provided us with one static ip address.We are using broadband modem.Now I would liket to map this static ip address to one of the private ip address which is 192.168.1.2(database server).i want to do nat above ips if i do so then i dont have no ip to assign to my outside interface.I would like to access this device over internet, by typing my public (Static ip ) given by the BSNL.security device i have is cisco ASA 5505.
View 3 Replies
View Related
Feb 3, 2013
I have ASA 5505 with basic licence, v9.1, ASDM 7.1. I want to create the DMZ for a web server.
The interface 0 is for the outside network The interface 6 is for the DMZ All other interfaces are for the inside network
My ISP provided me with one public static IP address, one gateway address and a subnet mask 255.255.255.252
1/ I would like to ask which interface I should assign the public static IP address to. Should it be assigned to the outside interface 0, or should it be assigned to the DMZ interface 6, while outside interface would be configured to use DHCP?
I tried to assign the static IP address to the outside interface first, but then when I used ASDM the “Public Servers” feature to configure NAT, I get error message that the outside interface and the public address cannot have the same IP address.
2/ For the sake of peace of mind, I am thinking about using the second firewall, which would be used only for the inside network. Can I connect this second firewall to one of the inside interfaces of the 1st firewall,
View 4 Replies
View Related
Mar 22, 2012
I have created a simple static ip address by using this command:
interface Vlan1
nameif inside
security-level 100
[Code].....
But, no matter what, the I can't ping the static address or access the computer 10.2.1.2 from outside of the asa 5505. I have attempted to ping from inside of the asa 5505 or from another computer. I just does not work.
I also have created several rules that allows icmp traffic.
icmp unreachable rate-limit 1 burst-size 1
icmp permit any echo-reply inside
icmp permit 10.2.1.0 255.255.255.0 inside
icmp permit any echo-reply outside
icmp permit any outside
View 1 Replies
View Related
Mar 20, 2012
I just upgraded my firewall to ASA 5505. Now, my original static ip address cofiguration is gone. Apperantly, Cisco went away from static ip address to something like nat (inside,outside) dynamic interface. how to create a static ip address under version 8.4? By the way, I am sharing what my configuration used to look before upgrading.
!
hostname cisco-asa
domain-name default.domain.invalid
names
!
interface Vlan1
nameif inside
security-level 100
[code].....
View 7 Replies
View Related
Feb 23, 2013
I was checking out the config on my ASA and noticed a bunch of static routes configured when I did a show route. With the exception of two that I expect to be there, the remainder point traffic destined for specific internal hosts to the outside interface, i.e.
S private_ip 255.255.255.255 [1/0] via public_ip, outside
I verified that I cannot ping those hosts from the firewall. I logged in to the ASDM. When I check the Configuration>Device Setup>Routing>Static Routes it only shows two static routes, the ones I expect to see. If I look under Monitoring>Routing>Routes, I see the same output as I did on the CLI. I looked around to see if I was missing a key location for this information, and I was able to see the same static routes output in Monitoring>Routing>Routes. Since this is under monitoring though there's no way to delete these routes, and I still don't know where they were configured originally. Then I happened to check under Monitoring>VPN>VPN Statistics>Sessions, and I see several of the private IPs used in the static routes being used by VPN users, including my own! I know I didn't assign myself a static IP for VPN use or anything like that. So, what are these static IP routes? Why do I see them in the CLI and not under the Configuration tab? I mean, I know I can delete them from the CLI but I'm trying to figure out why the info is not synced. Am I seeing dynamically created content based on the VPN connections?
View 2 Replies
View Related
Mar 17, 2012
working config with least amount of code for:
IOS post 8.3
Subnet: 192.168.1.0 /24
Static NAT (from any source) to server 192.168.1.100 and allow the same incoming connections on outside interface
Ports:
TCP 20,21
TCP 80
UDP 50000-50020
View 1 Replies
View Related
May 24, 2011
I have an ASA 5505 that I log into and currently only need a password to log onto the device. How do I set it up so a username is required as well?Another user needs to access the device. How would I set that up so they have to user their own credentials? I tried username apssword priv command and it does not work.
View 1 Replies
View Related
Dec 26, 2011
We have a working config with 1 external IP, we need to a second webserver (https) and it should be routed via a second public IP address. I already tried some suggestions from the community but haven't been able to find the solutions.
xxx.xxx.xxx.194 is going to the internal IP of 192.168.60.1 for OWA (https)
xxx.xxx.xxx.195 should go to a new webserver on 192.168.60.3
both server should be connected using SSL This is the current configuration :
ASA Version 8.3(1) !hostname fwdomain-name domain.localnames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.60.250 255.255.255.0 !interface Vlan2nameif outsidesecurity-level 0ip address xxx.xxx.xxx.xxx 255.255.255.0 !interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone CEST 1clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00dns server-group DefaultDNSdomain-name domain.localobject network obj_any subnet 0.0.0.0 0.0.0.0object network NETWORK_OBJ_192.168.70.0_26 subnet 192.168.70.0 255.255.255.192
[code].....
View 3 Replies
View Related
Sep 10, 2011
Attached is my updated ASA 5505 (8.4[2]) config. With this config, basically the "laptop" group works fine, but the leo and orion groups don't ever receive packets inbound. No DNS, nothing.
The laptop is windows, the other two are servers with two NICs. The interface cards are Intel Pro/1000s. I've been through everything including Vlan protocol conflicts and actually enabled the servers for 802.1(Q).
View 19 Replies
View Related
Oct 16, 2011
I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
object network obj-10.1.1.254
host 10.1.1.254
object network obj-10.1.1.254
nat (inside,outside) static 172.25.10.3
I want to also use nat (inside,backup) static 172.25.10.3
View 3 Replies
View Related
Jun 20, 2011
is this possible to configure HTTP traffic to ISP2 and Static NAT to ISP1 on ASA5520?
View 2 Replies
View Related
Sep 20, 2012
I have been using static NAT to map between a single server behind an ASA 5505 and a single public IP address. In other words, I've been doing this:
object network NAT_ME
nat (inside,outside) static interface
Now I would like to start using the clientless VPN feature of the ASA, so I of course don't want that particular port forwarded to the server. Is there a way to define such an exclusion? I've tried several things, including setting up a separate NAT rule to direct that port back to the ASA's interface, without luck.
If that is not possible, what configuration would I need to move to in order to get the behavior that I want? It is important that all (non-VPN) traffic is passed exactly as it arrives at the firewall (whether it is coming from internal or external), with the exception of changing the IP address (i.e., I need static port mappings for some of my services).
View 5 Replies
View Related
Jan 8, 2012
i have 6509+FWSM(4.0.4) now i wanna use stite to stite and ez vpn in the fwsm (multiple context) multiple context mode in fwsm support ipsec vpn?
View 2 Replies
View Related
May 22, 2011
I have 3 networks coming on DMZ (VPN) interface. Only one network is able to ping the DMZ interface. See below networks coming i on the DMZ.
10.132.24.0/2410.132.25.0/2410.132.26.0/24 Only the 10.132.26.0/24 netork works as it is in the same range as the DMZ interface.
allowing the other two networks to communicate. I've attched the diagram and configs for your perusal.
View 1 Replies
View Related
Nov 8, 2011
I have a problem with a ASA 5505. He is crashing multiple times during the day. I've setup a syslog server en I'd noticed that the last two log notification were:
2011-11-08 12:28:19 Local4.Debug 10.0.0.254 %ASA-7-711002: Task ran for 27016 msec, Process = Dispatch Unit, PC = 84745ce, Traceback =
2011-11-08 12:28:19 Local4.Debug 10.0.0.254 %ASA-7-711002: Task ran for 27016 msec, Process = Dispatch Unit, PC = 84745ce, Traceback = 0x084745CE 0x08474942 0x08475511 0x08475DB7 0x08475EDA 0x08508D9B 0x0850908A 0x083AB5B8 0x083A1D55 0x080655C1 0x08895A19 0x08895AD0 0x08952194 0x08978450
It's a 5505 with a 10 user inside host license, wich incidentally is more.
View 2 Replies
View Related
Sep 13, 2012
We currently have 2 different ASA 5505 connect to our ASA5510. We want to VPN connect the 2 5505's to each other while still mantaining connection to our 5520. I have attached pdf of what we have. What we want is to connect traffic between the two 5505's so that devices in either location can talk to each other while still mantainig connection to the 5510.
View 13 Replies
View Related
Jan 7, 2013
I want to know with an ASA 5505 w/ Security Plus License I get up to 20 VLANS/Named Interfaces.I have a customer that is getting a new subnet of external IP addresses from their service provider and a different default gateway to accomodate re-hosting their datacenter at their main office instead of at a Colo. My question, when building out their new DMZ, can I have multiple route 0.0.0.0 commands?
Example.
Current Default Gateway 1.1.1.X
Internal hosts 192.168.1.0 use and are natted to 1.1.1.X
New Default Gateway for DMZ Servers 2.2.2.x
Internal hosts still use 1.1.1.X, but server hosts in 192.168.1.3 should use 2.2.2.X -- there are also a bunch of pre-existing static NAT rules for these servers such as 2.2.2.30 translates to 192.168.1.30.
I think I would accomplish this by using the following:
route inside 0.0.0.0 0.0.0.0 1.1.1.X
route DMZ 0.0.0.0 0.0.0.0 2.2.2.x
Would this be correct?
View 2 Replies
View Related
