Cisco Firewall :: Configure HTTP Traffic To ISP2 And Static NAT To ISP1 On ASA5520?
Jun 20, 2011is this possible to configure HTTP traffic to ISP2 and Static NAT to ISP1 on ASA5520?
View 2 Replies
ADVERTISEMENT
Cisco Firewall :: ASA 5505 - Http Inspection Dropping All Http Traffic
May 9, 2012I am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
Here is the setup: I'm not sure why the web traffic is getting dropped.
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
[Code].....
Cisco Firewall :: ASA5520 - Static Route Shows A-172.24.0.0 Or A-192.168.176.0
Jul 14, 2012We use ASDM 6.2 to manage our Cisco ASA 5520 running ASA Software Version 8.2 (1). I just noticed that some static routes have "A-" when you view the static routes with ASDM e.g. A-172.24.0.0 or A-192.168.176.0 (pls see attached print screen). I haven't seen this before and dont know what it means.
View 4 Replies View RelatedCisco Firewall :: ASA 5510 ISP1 Does Not Respond
Nov 8, 2012I have an ASA 5510 and two IPS connections. I need ISP2 to take over when ISP1 does not respond. I have followed the following link ASA/PIX 7.x: Redundant or Backup ISP Links Configuration Example and as far as i can see this part is working. I disable interface for ISP1 and the routing table changes its static route to ISP2. When i enable ISP1 again the static route changes to ISP1. However no traffic flows to the outside. I have set up a nat rule that is the same as for wan1.
View 10 Replies View RelatedCisco Firewall :: Redirect HTTP / Ftp Traffic (ASA 5510)
Apr 25, 2011i have the following scenario :
ISP1-------ASA 5510----------ISP2
|
|
|
LAN
i would like to use ISP2 for all http/https/ftp traffic.how could I force my ASA to set a different gateway for http/https/ftp traffic ?i have tried several solutions such as nat/pat rules, nothing seems to work.
Cisco Firewall :: ASA5520 8.0(2) Does Not Have Traffic Shape Feature
Dec 21, 2011Recently I want to apply traffic shape on my ASA5520, but after entering the configure mode of policy-map, I couldnot find the shape command.. If I type the command, the device would notify me that there is no such command.. My version is 8.0(2),PS. Police command is working fine...
View 5 Replies View RelatedCisco Firewall :: Redirect Http And Https Traffic From ASA 5520 Via Squid?
Dec 20, 2010Right now, in my network there is no proxy server and all users go straight through the ASA to access internet. I would like to put a squid with dansguardian (for web filtering). Steps in getting all http and https traffic from ASA go via my squid?
View 18 Replies View RelatedCisco Firewall :: ASA5510 - Redirect HTTP Traffic To Internal Proxy?
Feb 13, 2011I am using ASA5510 and i want to know if it is possible to redirect http traffic to an internal proxy software. I explain : PC from the LAN use a internal proxy in their IE browser but some other PC doesn't use it.They are directy connected to the Internet using the Public IP from the WAN interface ( via NAT). Can we redirected this HTTP Traffic from the WAN interface to the Proxy in the LAN ?
Http Traffic will be routed like that : PC -> WAN interface -> Proxy -> WAN interface -> Internet In fact,can we create a rule saying : All http traffic which doesn"t come from the IP Proxy must be redirected toward proxy.
Cisco Firewall :: ASA 5505 - Redirecting Http And Https Traffic To Proxy Server
Aug 5, 2008I have an ASA 5505 that I am using to connect my contractors to via an inside interface, the outside interface is my private LAN. I have setup on our corporate Proxy server to allow traffic from my outside interface of my ASA to go to the internet without credentials BUT log internet activity. The question is I want to know if the ASA can send that http & https traffic to my proxy server and all other traffic to my default route? I want to be able to send all internet traffic to my proxy server. This will avoid me asking the contractors to place proxy credentials in their browsers.
View 6 Replies View RelatedCisco Firewall :: 5510 Unmatched HTTP Traffic To Symantec Public Transparent Proxy
Sep 4, 2012I am working on a task of redirecting any unmatched http traffic to Symantec public transparent proxy through Cisco ASA. For the definition of uncatched http traffic, we have inbound squid servers for deploying IE proxy pac and redirect the http traffic to Symantec public transpraent proxy, however we can't deploy IE proxy pac to mobile device and non-support web browers.Since we have some application using IE proxy setting for direct http communication with external domains, the current symantec policy addes those domains in the exception list so that they are not redirect to Symantec public transparent proxy server.
-For the platform - Cisco ASA 5510 ASA 8.4(4)1
-For the solution, I have the following two nat rules
Cisco Firewall :: How To Configure Multiple Static IPs On ASA 5505
Jun 10, 2011I am setting up a Cisco ASA 5505 first time for My organisation, I usually setup Cisco Router, I have 10 Static IP, & Have 6 Server (S-1, S-2, S-3, S-4, S-5, S-6), Traffic Should be pass through the ASA and is distributed to the destination server that is specified in the packet. LAN servers can be separated into discrete networks for security. For example, a private LAN for internal traffic accessed only via remote dial-in VPN sessions and Want to Configure DMZ for Server (S-4, S-5, S-6) that allows public web traffic.
I have Attached My Network Diagram I have some question,
1:- Can we Configure Multiple Static IP On ASA 5505 ?
2:- If Diagram is wrong what change need to be done ?
Cisco Firewall :: Pix 501 (6.3) VPN / Cable Modem - Can't Configure Static IP
Sep 23, 2011I have a Pix 501 running 6.3 code sitting behind a cable modem. I use ip address outside dhcp setroute because I don't have a dedicated IP from my cable provider.
How do I configure the Pix to host VPN connections from my iPad when offsite? Since the outside interface is going to change, I can't configure a static IP.
Cisco Firewall :: ASA 5510 Static To Indirect Subnet / Return Traffic Without Default Route NAT?
Aug 12, 2012I am having touble with a NAT concept. What I have is a 3rd party software VPN product that basically tunnels encapsulated traffic to/from a server sitting inside the network. Right now this traffic utiluizes a physical interface on the ASA5510, but I need the interface for another project.
What I have is this:
Internet<----->ASA<-->router<-->4507(layer3)
| |
| |-Vlan1
[Code]......
Cisco Firewall :: Asa 5520 / Configure Two Static Nat Statements From Inside To Outside And Backup Interface?
Oct 16, 2011I have a asa 5520 with an outside and backup interface. I am trying to configure two static nat statements from the inside to the outside and backup interface. Here is what I have configured so far.
object network obj-10.1.1.254
host 10.1.1.254
object network obj-10.1.1.254
nat (inside,outside) static 172.25.10.3
I want to also use nat (inside,backup) static 172.25.10.3
Cisco Firewall :: How To Configure ASA5520 For Active / Active
Mar 17, 2013How to Configure ASA5520 for Active/Active
View 8 Replies View RelatedCisco Firewall :: ASA5520 To ASA5520 Via L2L Tunnel
May 31, 2011Our firewall expert has gone off on long term illness leave and I am trying to pick up the pieces :-(
We have an ASA 5520 (local office) talking to another ASA (remote office) via a VPN Tunnel.
My 1st problem is that I cannot ping from my inside network (local) to the outside interface of my remote ASA.
My 2nd is that I have debug enabled on my rules but am not logging anything.
Cisco VPN :: Remote VPN On ASA5510 Getting Static IP From ASA5520
May 22, 2013i configured a remote VPN on cisco ASA 5520 and everythings seems to be working fine...DHCP IP were been lease to users that connect to the VPN. but the issue now is that our customer want a static IP to be given to a particular user when he connect via VPN.
View 1 Replies View RelatedCisco Firewall :: Configure ASA 7.2 (4) To Inspect SCCP Traffic From A CUCM V7
Aug 11, 2010I am trying to configure my ASA 7.2(4) to inspect SCCP traffic from a CUCM v7.I have been advised that the ASA device needs to support the version of Skinny I am running.What version of Skinny does ASA 7.2(4) support? How can I find out what version my phones are using?
View 3 Replies View RelatedCisco Firewall :: ASA5580 - How To Configure Traffic Flow Idle Time-out With CSM
Feb 16, 2012I am looking for the way to define an idle timeout for specific flows on an ASA5580 by using Cisco security manager. For ex I needed to define a specific idle timeout for connections beetween specific devices (Devices in vlan1, Device2 in vlan2).To test it I did following changes by CLI and it works fine. access-list L1 extended permit ip <@IP1> <mask1> host <@IP2> class-map CM1 match access-list L1 policy-map PM1 class CM1 set connection timeout idle 02:00:00
I try do do the same configuration with CSM in order to be able to manage each changes only by using CSM.So I defined Access control list, Traffic flow and then I define timeout in CSM --> PIX/ASA/FWSM Platform --> Service Policy Rules --> IPS, QoS and Connections Rules -> connections settings -> Traffic flow idle time-out. The problem is that each time I deploy the configuration with CSM I loose the timeout config line which is the most important for my application..
Cisco Firewall :: Configure ASA 5510 For Individual Server Traffic Routing
Jan 27, 2013I am wondering if this is possible. We have multiple internet connections with fixed IP's coming into the office. We'd like to use one for FTP backup and another to service our websites. From what i have read a 5510 doesn't do policy based routing, but we'd like to configure our ftp server to use one of the internet pipes and our webserver to use another internet pipe. Is that possible?
We'd have two outside fixed IP interfaces and two internal interfaces. I could then use one of the internal interfaces for the web server and the other for the FTP server. consequently if the internal web server and FTP server use the fixed IP"s corresponding DNS server wouldn't that effectively route all FTP traffic out one interface and all web traffic out the other?
Then the FTP traffic would be NAT'ed to an internal interface and the HTTP & HTTPS traffic would be NAT'ed to a separate internal interface.
Then if each of the internal servers used the corresponding internal NIC on the ASA as it's gateway and the fixed IP's that correspond to the external DNS server, then it would affectively only use that gatway out for traffic? Would that work? Does it should route traffic out those pipes correct? Will the asa support two different next hop routers for the two different interfaces?
Cisco Firewall :: Configure ASA To Send All Traffic From (3) VLans To Interfaces That Connects To 2960?
Apr 18, 2013I have a an ASA 5520 connected to a Layer 3 (3750) switch (Inside) and a connection to a 2960 switch (Outside) to get to the internet. . I have created vlan interfaces on the 3750 switch and enabled ip routing on the switch to enable the vlans to communicate with each other.
Vlan Interfaces on the switch:
Vlan 100 172.17.1
Vlan 200 172.18.1
Vlan 300 192.168.3.1
I want the devices connected to the 3 vlans to be able to pass through the firewall and get out to the internet.I have connected the ASA to the 3750 by routed interfaces (10.10.10.1) --------- (10.10.10.2) and they are able to ping each other.I have also put a default route on the 3750 sending all traffic from the switch to the ASA inside interface (10.10.10.1)The issue that i am having is that the ASA also connects to a 2960 which has a connection to the Internet, and they are handing off an ethernet connection from the 2960 that sits in VLAN 55 (Vlan 55 is the Internet accessible vlan).How do I configure my ASA to send all traffic from my (3) vlans to the interfaces that connects to the 2960 switch?
Cisco Firewall :: 5510 How To Configure Local LAN SMTP Traffic Sending Through New Leased Line
Jun 11, 2012We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
Cisco WAN :: Http Traffic Hanging Through 2821 Router
Mar 28, 2011I'm using a Cisco 2821 router to provide temporary Internet access for a private network of about 300 users for a conference at a hotel. The hotel has provided me a public IP address for the WAN side. On the LAN side I have a 10.x.x.x /8 subnet with the router providing DHCP and NATing (overload) across the WAN interface.
Users can pick up an IP address and access the web. Light web pages such as Google tend to load without issue, however if a user does something that takes more time, such as streaming a Youtube trailer or opening an RDP session, the connection will freeze.
It doesn't appear to be related to bandwidth availability. Pings return on average 10-15 ms. However, I will get a request time out about every 10th continual ping. Steaming video will load about 4-6 seconds worth of data, then will appear to freeze without dropping. Doing something like speedtest.net will send a large amount of data then will hang, without ever ending the conversation.
This doesn't happen when I plug a laptop directly into the hotel public Internet line. They also don't have issues with their network similar to this.
I do not have any ACLs, etc. loaded. The router is basically wide open as far as I can tell. I don't see the router resources getting used much at all.
Cisco Switches :: FS-300-24 QoS To Limit HTTP And HTTPS Traffic
Apr 20, 2011Never seen a Cisco, or any other L3 switch before. Nor an Lx router. Any step by step,or class room or web based training, or a partner or Cisco helper to get us up to speed on this.Goal is to limit http and https traffic in favor of telnet to an AIX server and RDP to a Windows TS. Printing would be ahead of http/s and below the others.
Interstingly, the web site promises 9 videos, but there are only 8. The demo guide says about OoS: "Coming Soon".Where to go? Who(m) to call?
How To Tunnel HTTP Traffic In VPN Based Connection
Mar 1, 2011I have Site(s) Ani....i=1,..10 sites which communicate with site B to access a website/application. That's simple enough. However, the traffic is http well we primarily don't need https on ipsec tunnel right?. But since attacks related to eavesdropping of traffic come a real reality once it gets terminated by the ipsec device on both side.I have two options either to purchase a third-party ssl certificate to encrypt the traffic between two nodes or use a custom made one.I don't want to use a custom made one because this make the browser prompt an ugly untrusted certificate message; its ugly not from security perspective but for clients inconvenience and assuring users confidence in our systems is a critical issue for us. ?
a) How its possible to remove ugly certifcate message from user screen? Does the company need to register its certificate to some kind of CA body? or what ...
b) Due to some tcp acceleration issues, ssl traffic slows down the traffic between the nodes so we only require the encryption to stand just during the initial handshake when the username and password are being validated ; after that we want to revert back to http?
How To Configure Server To Act As HTTP
Jan 21, 2012i had done inter-vlan routing , attached a DNS server to that network, i didn knw how to config a server to act as http??? so that i can view webpages forn systems of that network??
View 3 Replies View RelatedCisco Switching/Routing :: 6509 Unable To Redirect Http Traffic
Mar 26, 2012On a Catalyst 6509 switch I have configured wccp protocol in order to redirect the Http traffic to a Bluecoat SG8100. It was working fine until a new L3 interface implementation.Thereafter I was unable to redirect the http traffic due to an error reported from the Cat6509: [code] After some checks I supposed that the problem should be the UDP 2048 port connection between the Switch and the Bluecoat while the switch L3 port and the bluecoat are on the same Lan. A deep analysis found that the WCCP protocol seems to be as follow:
-Proxy address 10.64.28.240 to Switch Port 10.64.28.250 Here I Am
-Switch Port 10.64.28.250 to Proxy address 10.64.28.240 I See You
-Switch Port 10.66.0.251 to Proxy address 10.64.28.240 UDP 2048 packet (dropped by firewall)
It's strange to me that the first dialog is correctly handled by the correct Cat6509 interface while the UDP packets are flowing from another Vlan interface not configured with the WCCP and apparently not involved on the protocol.Last of all the WCCP is now disabled and unusable?
Cisco Application :: Can ACE (4710) Behave As Reverse Proxy For HTTP And SSL Traffic
Jul 12, 2011Can the ACE appliance behave as a reverse proxy for http and ssl traffic? I would assume it can given how it does SLB but SLB is not a requirement at this time.
View 2 Replies View RelatedCisco Switching/Routing :: 3750 Cannot Mark Http Traffic With DSCP
Mar 14, 2012I am trying to mark http packets from a web server with DSCP ef, but when I am doing a traffic capture all http packets have tos 0x0.I am able to mark UDP and ICMP packets originated from this server, but not any TCP traffic.The web server is in VLAN 20This is my config mls qos ip access-list extended MARK-HTTP-ACL permit tcp host 10.10.10.10 eq www. [code]
View 4 Replies View RelatedCisco WAN :: ASA 5505 - Forwarding All Incoming Traffic To Two Internal HTTP Server
Oct 2, 2011We have Cisco ASA 5505, 90.x.y.2/29 IP is assigned to outside interface. We have one internal HTTP server so that I use static (inside,outside) tcp interface [URL] to forward all incoming HTTP traffic to internal HTTP server 1. Now we need to add new physical HTTP server 2 so that I would like to forward
HTTP traffic to e.g. 90.x.y.3/29 to 172.16.0.11.
How can I do that? See scenario image (scenario.png) if needed.
D-Link DIR-655 :: Routing All HTTP / Port 80 Traffic To Proxy Server?
Jul 18, 2011I have a setup like this.
Foreach computer I need to go and configure the browser proxy settings and some people are getting smart and turn it to automatic configuration again.
So what i want to achieve is to have my DIR-655 to route all the HTTP/port 80 traffic to the proxy server.
That way it is transparent and then it is not needed to configure each computers browser settings.
I am pretty new to this and the router configurations.
The proxy server works fine if i configure the browser manually.
Cisco Routers :: RV042 Setup To Grant HTTP Traffic Minimum Bandwidth?
Jul 24, 2011I am trying to set up my router to grant http traffic a minimum bandwidth of - for example - 5,000 kBit (if there is any http traffic).
So I set http min. rate to 5,000 while I set nntp min. rate to 1 However, when I run nntp downloads on several connections (e.g. 10) my single http download never goes above 1,000 kBit. Without any other connections I reach 8,000 kBit.
I am using a single 12 MBit line.
Cisco Switching/Routing :: Configure Tacacs Authentication For Http In 2960
Oct 13, 2011I am trying configure tacacs authentication for http in Cisco 2960 with IOS 15.0.1.SE. [code] But the device is not authenticating. It ask the credentials (user and pass) but not authenticates.
View 7 Replies View Related