How To Configure Server To Act As HTTP
Jan 21, 2012i had done inter-vlan routing , attached a DNS server to that network, i didn knw how to config a server to act as http??? so that i can view webpages forn systems of that network??
View 3 Repliesi had done inter-vlan routing , attached a DNS server to that network, i didn knw how to config a server to act as http??? so that i can view webpages forn systems of that network??
View 3 RepliesI am trying configure tacacs authentication for http in Cisco 2960 with IOS 15.0.1.SE. [code] But the device is not authenticating. It ask the credentials (user and pass) but not authenticates.
View 7 Replies View RelatedWe want to mask part of the path prefix to hide development content: For example: the site(s) are: [URL]However we don't want anything with acme showing...so we would want the loadbalanced url to be: [URL] ...for requests and responses. I think this would be an http re-write request/response scenario?Is this possible to configure this on the ACE Device? We've got the load balance configuration down...not sure how to do this re-write type scenario?
View 2 Replies View Relatedis this possible to configure HTTP traffic to ISP2 and Static NAT to ISP1 on ASA5520?
View 2 Replies View Relatedwe are having some trouble setting up our router (Cisco 861W) webserver on the LAN so that it can be accessed from outside (http via port 80). When we try to access it via the web address, we just get the login window of the Cisco router software?
View 10 Replies View RelatedI have one server-A(windows 2008) installed one application called"host front" which gives athentication to connect Linux(mainframe console)server(SERVER B). These 2 servers are bihind the firewall.If one internal user who has the athentication to logine server-B ,tried to login server A,will get the" username and password"screen and once they enter the username and password ,will get the server-B screen.But if somebody try to connet via MPLS(we need to test MPLS site customers) from outside via ASA 5540 ,to server-A will get the "username password" screen and once enter the credentials,after 1 minitue will get error"http server faild to send datas to the server" and will not move to server -B screen.Where do you think is the problem?
View 3 Replies View RelatedI just upgraded my ASA 5585 cluster from 8.2 to 8.4. I also upgraded the asdm .bin from 6.35 to 6.43. after rebooter the cluster, I try to access it with ASDM installed on my computer but it blocked at 17%.I tried to access [URL] but I just an error (with IE & FF) [code] What did I miss in the ocnfiguration ? I precise that I never used the http page, I already had the ASDM installed from another ASA.
View 4 Replies View RelatedI using IOS c2950-i6k2l2q4-mz.121-22.EA14.bin but no support command "ip http secure-server" and I not connect switch by CNA. How I fix ? Or IOS C2950 support ip http secure-server and ssh ver2 ?
View 1 Replies View RelatedI have a customer who used to own a 3750 with a older version of IOS. The switch he had used a three year old version of IOS which allowed him to browse to the switch IP and manage it via HTTP without entering a password at all. Now that he has a replacement switch with a new ver of IOS (since the previous switch died). We slapped the config on from the old switch but no matter what we do (understanding that new http aaa authentication commands were added) we cant get this thing to let him in without prompting him for a password. I understand this was an insecure config to begin with so I shouldn't be advocating using it in the first place, but this is what the customer wants.Basically what I'm trying to figure out is are we banging our heads into the wall for nothing as the "ip http server" will not allow an authentication method of "none" anyway? None of the offical documentation I have read for the http aaa authentication cmds shows this as an example nor have I found any blog posts on how to do it ether. Perhaps Cisco removed this by design.
Here is the config:
aaa new model
aaa authentication login default local
aaa authentication enable default none
aaa authentication login none none
ip http server
ip http authentication aaa login-authentication none
[code]....
I have a setup like this.
Foreach computer I need to go and configure the browser proxy settings and some people are getting smart and turn it to automatic configuration again.
So what i want to achieve is to have my DIR-655 to route all the HTTP/port 80 traffic to the proxy server.
That way it is transparent and then it is not needed to configure each computers browser settings.
I am pretty new to this and the router configurations.
The proxy server works fine if i configure the browser manually.
We have ASA5520 and we want to configure a VPN IPSEC profile so that a partner of ours can access only a server and only on HTTP port.I've tried configuring split tunneling with an Extended ACL but probably I'm missing something. I just configured the ACL so that it included any source to our server's IP on HTTP port but when testing, it didn't work.
However, if I configure a Standard ACL on the split tunneling I can access the server and all the services it provides.Do you know if I'm missing anything on the Extended ACL configuration?
Should I configure this any other way?
I recently bought a EA6500 to replace a EA4500 (defective). Prior to the EA4500 I had a 160N which I now use as a WAP for 801.11G devices. I thought the 4500 was good from the media server functions it offered.However since installing the 6500 I noticed:
1. I have port forwarding for http to a web server. It works fine from machines on the outside but from my local subnet 192.168.1.x I can't access the web server (I can't even ping the external address - and yes I turned the anonymous filter off). I am not using ddns and I have a static ip address (cable modem connected) to the outside world.
I recently "inherited" a CSS 11503 - I've only used ACEs before - and I want to get HTTP keepalives working.To start, I created a test service:
lb-1# show run service sunbird-http-7025-test
!************************** SERVICE **************************
service sunbird-http-7025-test
port 7025
ip address 141.211.229.168
[code].....
I have one server-A(windows 2008) installed one application called"host front" which gives athentication to connect Linux(mainframe console) server (SERVER B).These 2 servers are bihind the firewall.If one internal user who has the athentication to logine server-B ,tried to login server A,will get the" username and password"screen and once they enter the username and password ,will get the server-B screen.But if somebody try to connet via MPLS(we need to test MPLS site customers) from outside via ASA 5540 ,to server-A will get the "username password" screen and once enter the credentials, after 1 minitue will get error"http server faild to send datas to the server" and will not move to server -B screen.
View 1 Replies View RelatedI need getting access to my http server. I have a host name that I configured to point to my IPS IP address. Port 80 is enabled on my server, but I can't seem to get access it from my web address [code]
View 5 Replies View RelatedWe have Cisco ASA 5505, 90.x.y.2/29 IP is assigned to outside interface. We have one internal HTTP server so that I use static (inside,outside) tcp interface [URL] to forward all incoming HTTP traffic to internal HTTP server 1. Now we need to add new physical HTTP server 2 so that I would like to forward
HTTP traffic to e.g. 90.x.y.3/29 to 172.16.0.11.
How can I do that? See scenario image (scenario.png) if needed.
I'm looking fot a way to do static URL blocking with ASA and when the URL is blocked present a "Web Page" to the user saying that it's been blocked.
So, i was wondering if i can use the http parameter "spoof server string" to replace the original URL sent by the user for another URL that points to an internal web server holding a basic page saying "Your URL request has been blocked".
The point is to have a way to tell users that the page they are trying to browse is blocked by a policy.
cisco WS-C6509-E Core switch with IOS "s72033-ipservicesk9_wan-mz.122-18.SXF11"
i have 2 question
Q.1 i want to upgrade this switch what is the latest IOS ver. supported by this module ?
Q.2 i need to enable http server on this switch when i run this comman it's accsebt but i cant get http work
I have an ASA 5505 that I am using to connect my contractors to via an inside interface, the outside interface is my private LAN. I have setup on our corporate Proxy server to allow traffic from my outside interface of my ASA to go to the internet without credentials BUT log internet activity. The question is I want to know if the ASA can send that http & https traffic to my proxy server and all other traffic to my default route? I want to be able to send all internet traffic to my proxy server. This will avoid me asking the contractors to place proxy credentials in their browsers.
View 6 Replies View RelatedI am testing out some inspection options on an ASA 5505, and I am running into a situation in which applying a http inspection is dropping all outbound http traffic. I get a "protocol violation" error in the logs.
Here is the setup: I'm not sure why the web traffic is getting dropped.
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
[Code].....
I am trying to configure interface vlan1 to get an ip address from dhcp by entering the commnad ip address dhcp ios rejects the dhcp portion of my command as not recognised although it is referred to in Cisco manuals.my IOS version is c2950-i6k2l2q4-mz.121-22.EA14.bin.I get the same problem when I try to configure ip http secure-server on the switch. Is this a known bug or whether I have the correct IOS version for these commands?
View 6 Replies View RelatedI know the best thing one should do is install an ISA server and an Active Directory Domain Controller on separate servers. But for some reason, I want to configure my Windows Server 2003 as an ISA server as well as an Active Directory Domain Controller. What can happen to my server making it run improperly. For example, my ISA server will function mainly as a Firewall, I wonder if all the rules I create in ISA server determine what I mean it should work or I have to consider any affection from Active Directory DC to those rules?I have to ask this question because I've already installed both ISA and AD DC on my Windows Server 2003, already created an Allow. All rule (just for testing connection) in ISA server but I can't ping from all the clients to my server, all the clients can ping each other and the server itself can ping to all clients. I just think that may be the affection from AD DC to my AllowAll rule in ISA server.
I successfully created some rules that worked greatly as they should work but when I hadn't installed AD DC yet (just installed ISA), however right after installing AD DC, it still worked well (this made me think that AD DC didn't affect to how ISA works). Then I configured a little related to DNS server, and maybe something I don't remember exactly and now I can't ping from my client PC to my server. My network is virtualized using VMware 8 workstation and GNS3, at first there is no need of GNS3 because I just want to test my internal network (some clients connected to the internal interface of ISA server). Depending on VMware that I can't be sure if it is some fault of VMware or any other thing but my configuration on the servers.
I want to know, is it possible to configure VPN server over LAN? VPN server will have access of internet through ISP's Router. We have already purchased STATIC IP. I have tried it with Windows server 2003 for VPN server and Windows Xp with Client servers. But i;m unable to establish the connection between VPN server & VPN Client. IS there any software to diagnose that where problem exist actually.
View 1 Replies View Relatedhow to configure caching server .
View 3 Replies View Relatedsend me step by step guide of how to configure SNP server for SNMp trap
View 2 Replies View RelatedHow to configure Radius server on router in packet tracer
View 1 Replies View RelatedI am in search of a low cost network camera that i can see online, and by going on numerous sites, and conversations i end up with dlink network camera. They are:
-DCS-932L
-DCS-2121
The best part about these are you just have to plug and view online.But now I am having one problem, the d-link people say that i can only see the video or image on mydlink.com otherwise I have to provide a dedicated IP address to the camera. And I want to view this camera via server IP address. Is there a way that I can configure the camera to my server IP address.If any one has used or know the camera which can be view online via IP, The main thing that I am trying to say is that i will extract the image via server ip and use it accordingly.
My ISP provides me internet connection through password protecting Access Point bearing IP address 192.168.20.1 built with IP filtering which allows only a particular IP 192.168.20.88. I am not able to access internet on more than one computers simultaneously because router allows only single IP and I am not sure what are the WAN IP's uses Access Point provided by ISP eg. IP, Gateway and DNS. My ISP provides me static IP address for home computer as mentioned below :
IP : 192.168.20.88
Gateway : 192.19.20.1
DNS: 192.168.20.1
Alt DNS : 192.168.20.1
My public IP address is 180.87.210.26.
Is there any option to add a router to bride or configure router as proxy server so that i can access internet more than one PC's simultaneously.
currently we are using a proxy (192.168.45.90) for internet. the internal network ip scheme is 192.168.30.0-254. my problem is that how should i configure the new ISA2004 installation on separate PC with new IP range like 192.168.31.0-254 using that proxy 192.168.45.90.
View 1 Replies View RelatedAs part of site to site VPN configuration, I need to configure VPN server & Client using Cisco 877 only.
View 1 Replies View Relatedis there a owners manual for Toshiba Canvio Portable Hard Drives?
View 1 Replies View RelatedI configured one Cisco 1760 router as VPN server using easy VPN Server. The clients can connect to the VPN server successfully. The problem is that there is no ping between the clients. They cannot see each other into the VPN network.The router has just one port.Do I need special configuration of the VPN sever in order to allow the VPN clients to connect each other or I need other type of VPN?
View 2 Replies View RelatedI have Linksys AG241 ADSL router. i have a IPSec vpn client installed on my laptop, so can i connect AG241 & access the hosts behind AG241?
View 1 Replies View Related