I want to know, is it possible to configure VPN server over LAN? VPN server will have access of internet through ISP's Router. We have already purchased STATIC IP. I have tried it with Windows server 2003 for VPN server and Windows Xp with Client servers. But i;m unable to establish the connection between VPN server & VPN Client. IS there any software to diagnose that where problem exist actually.
View 1 RepliesI know the best thing one should do is install an ISA server and an Active Directory Domain Controller on separate servers. But for some reason, I want to configure my Windows Server 2003 as an ISA server as well as an Active Directory Domain Controller. What can happen to my server making it run improperly. For example, my ISA server will function mainly as a Firewall, I wonder if all the rules I create in ISA server determine what I mean it should work or I have to consider any affection from Active Directory DC to those rules?I have to ask this question because I've already installed both ISA and AD DC on my Windows Server 2003, already created an Allow. All rule (just for testing connection) in ISA server but I can't ping from all the clients to my server, all the clients can ping each other and the server itself can ping to all clients. I just think that may be the affection from AD DC to my AllowAll rule in ISA server.
I successfully created some rules that worked greatly as they should work but when I hadn't installed AD DC yet (just installed ISA), however right after installing AD DC, it still worked well (this made me think that AD DC didn't affect to how ISA works). Then I configured a little related to DNS server, and maybe something I don't remember exactly and now I can't ping from my client PC to my server. My network is virtualized using VMware 8 workstation and GNS3, at first there is no need of GNS3 because I just want to test my internal network (some clients connected to the internal interface of ISA server). Depending on VMware that I can't be sure if it is some fault of VMware or any other thing but my configuration on the servers.
how to configure caching server .
View 3 Replies View Relatedi had done inter-vlan routing , attached a DNS server to that network, i didn knw how to config a server to act as http??? so that i can view webpages forn systems of that network??
View 3 Replies View Relatedsend me step by step guide of how to configure SNP server for SNMp trap
View 2 Replies View RelatedHow to configure Radius server on router in packet tracer
View 1 Replies View RelatedI am in search of a low cost network camera that i can see online, and by going on numerous sites, and conversations i end up with dlink network camera. They are:
-DCS-932L
-DCS-2121
The best part about these are you just have to plug and view online.But now I am having one problem, the d-link people say that i can only see the video or image on mydlink.com otherwise I have to provide a dedicated IP address to the camera. And I want to view this camera via server IP address. Is there a way that I can configure the camera to my server IP address.If any one has used or know the camera which can be view online via IP, The main thing that I am trying to say is that i will extract the image via server ip and use it accordingly.
My ISP provides me internet connection through password protecting Access Point bearing IP address 192.168.20.1 built with IP filtering which allows only a particular IP 192.168.20.88. I am not able to access internet on more than one computers simultaneously because router allows only single IP and I am not sure what are the WAN IP's uses Access Point provided by ISP eg. IP, Gateway and DNS. My ISP provides me static IP address for home computer as mentioned below :
IP : 192.168.20.88
Gateway : 192.19.20.1
DNS: 192.168.20.1
Alt DNS : 192.168.20.1
My public IP address is 180.87.210.26.
Is there any option to add a router to bride or configure router as proxy server so that i can access internet more than one PC's simultaneously.
currently we are using a proxy (192.168.45.90) for internet. the internal network ip scheme is 192.168.30.0-254. my problem is that how should i configure the new ISA2004 installation on separate PC with new IP range like 192.168.31.0-254 using that proxy 192.168.45.90.
View 1 Replies View RelatedAs part of site to site VPN configuration, I need to configure VPN server & Client using Cisco 877 only.
View 1 Replies View Relatedis there a owners manual for Toshiba Canvio Portable Hard Drives?
View 1 Replies View RelatedI configured one Cisco 1760 router as VPN server using easy VPN Server. The clients can connect to the VPN server successfully. The problem is that there is no ping between the clients. They cannot see each other into the VPN network.The router has just one port.Do I need special configuration of the VPN sever in order to allow the VPN clients to connect each other or I need other type of VPN?
View 2 Replies View RelatedI have Linksys AG241 ADSL router. i have a IPSec vpn client installed on my laptop, so can i connect AG241 & access the hosts behind AG241?
View 1 Replies View Relatedthe linux server should be configured with LDAP, so that any user should not login into that machine by local user credentials but by his intranet credentials.
View 1 Replies View RelatedI want to build up cisco 3800 series router as terminal server , i have Asycs 32A module in cisco 3825. Here is show version of device.Do i need to installed any specific IOS in Cisco 3825 device ? how to configure cisco 3825 as terminal server.
View 1 Replies View RelatedI am facing problem while connecting my VPN server configure at UC540 device. this device is behind my ISP router. i applied port forwording of IPSEC traffice to my cisco device which configured as vpn server. now if i try to connect with my Live IP i get the following error. [code] I test if i connect using 192.168.0.116 internally it works but if i try to connect using my Live IP it trying and trying but not connect..
View 3 Replies View RelatedHow do you configure a external FTP Server for Cisco NCS 1.1? I only get setup username/password, i also need to setup FTP server IP and directory.
View 1 Replies View RelatedI have a old Cisco 1760 router with VPN module. I want to use it as VPN server.I clear all the configuration of the configuration. I want to use the SDM to configure the VPN server.When I tried to configure the VPN sever from the SDM wizard this message appears:"There are no authorization lists configured on this router".
View 2 Replies View RelatedI have been trying to configure Cisco1941/K9 as Easy VPN Server through CiscoCP.The tunnel comes up but I cannot pass any traffic to the secure LAN (GigEth 0/1). When the tunnel comes up, I can ping the Loopback interface and the GigEth 0/1 interface IPs.
View 21 Replies View RelatedI´m trying to configure SR520 Cisco router as PPPoE server. The point is, when configuration is done and PPPoE client is directly connected to the interface, SR520 doesn´t respond to incoming PADI. PADI is not shown in PPPoE debugs (debug pppoe events, packets and errors).On the other hand, I get the PADI capturing packets with wireshark (so PADI is being sent) and the same configuration on other router works fine.
View 2 Replies View RelatedI want to configure my Cisco asa 5505 as a dns server, so that when i configure any of my network systems ip address and use my firewall as a default gateway and dns ip, the system should be able to browse internet.
View 5 Replies View RelatedWe have one Cisco ASA5515 firewall, I configured ftp mode to passive, inspect ftp in service, use anoother public to do NAT with ftp server, and also configued ACL in outside interface, but I failed to access the ftp server from internet use that public ip address, no problem to acces the ftp server use its inside address in LAN.
View 9 Replies View RelatedCan we Configure DHCP server in 3750 ? we have configure DHCP server in 1841 router but some reason we want remove router .
View 2 Replies View RelatedI have a 2811 router and how to configure a RADIUS server using the CLI.
View 3 Replies View RelatedI need to configure ntp on acs5.3 ,i dont know how to configure through gui mode,
View 1 Replies View RelatedI have a Cisco ASA 5510 and a Cisco ASA 5505. I want to configure the ASA 5510 as Easy VPN Server and 5505 as Easy VPN hardware client.Using either CLI or ASDM.
View 1 Replies View RelatedI'd like to configure a VPN with two SR520. the first router is a SR520-FE-K9 and it's at office, the second router is a SR520-ADSL-K9 and it's at home.
Each router have a static IP and individually works well. I tried to configure, by CCA, the office router as a server and the home router as a client: at home I can't see the office network and I can't navigate.
Need step by step, using CCA to configure a secure VPN.
I want to set up a domain for a file server and MS SQL 2005 server on my server machine and installed windows server 2008 in it.
Do I need to set up DHCP server and DNS on Windows server 2008R2 or leave them to the router to do the job?
In my office environment, my machine is configured with an IP address, Subnet Mask and a Default Gateway. The Default Gateway does not allow internet connectivity but is configured to provide us with connectivity to some server based tool.
Now in order to provide us with the internet access, a proxy server is configured via the LAN settings in the IE. The problem here is the Proxy is restricted for some sites that I need like certain technical blogs and all, which it filters out in the blogs category and does not load.
I do have another Gateway server address that I can use in Local Area Connection IPv4 Properties as Default Gateway address which removes this restriction. I thought that this should be configurable to the LAN Settings as a proxy as well. But when I do so, I lose the connection to the internet.
I am not sure if all Gateways can act as proxy servers. Or is there anything that I am doing wrong. I am using the default port 8080 in LAN Settings.I can ask this from the technician but I am not sure if he would be able to answer that as he is just a first level guy. I thought of figuring it out myself.
I've heard that you can configure an 1811 router as a terminal server for remote console work.I have several of them in the lab and would love to try it out.
View 2 Replies View RelatedI need to configure my ASA 5520 version 7.3 firewall to translate our SMTP server residing in local LAN to use different IP address from the outside interface which is used by all other computers to access Internet. Under NAT section, I have NATted this internal SMTP server with different IP address(eg x.x.x.1) and also translated the remaining IP addresses in the LAN to the outside interface(eg x.x.x.2)
my problem is, Whenever i check the header for message coming from the smtp server it shows that, the SMTP server is also translated by using the same outside interface public ip address(i.e x.x.x.2) which is used by other client machine to access internet instead of the x.x.x.1. How I can get my SMTP server to use separate IP and avoid to be blacklisted by some domain.
In my collage i have a LAN to the wind server 2003 again i m also configure a small LAN may be take a 5 computer but the communication is not done.
View 1 Replies View Relatedi have one machine have 2 Ethernet devices and i need to connect this server to different 2 network with 2 different gateways (192.168.2.x "vpn network" and 192.168.1.x "adsl network" )so if any other one need to connect this ftp server can connected from vpn or adsl
View 1 Replies View Related