Cisco Firewall :: 5505 Broadband Connection With One Static IP
Jun 3, 2013
I am mapping static ip address to the local ip address.We have a bsnl broadband connection, and bsnl has provided us with one static ip address.We are using broadband modem.Now I would liket to map this static ip address to one of the private ip address which is 192.168.1.2(database server).i want to do nat above ips if i do so then i dont have no ip to assign to my outside interface.I would like to access this device over internet, by typing my public (Static ip ) given by the BSNL.security device i have is cisco ASA 5505.
View 3 Replies
ADVERTISEMENT
May 26, 2011
I just replaced a PIX 501 with a new ASA5505. I had a very weird problem and would like to know what caused it incase I run into it again. The setup is a DSL connection, with an old-ish speedstream DSL modem. Static IP, no PPPoE. I had a PIX 501, then two servers with static NAT entries on secondary WAN IPs. Everything was working fine on the PIX, I just duplicated the config over to the ASA. I swapped out the PIX for the ASA, and rebooted the DSL modem to clear out it's cache. After installation, NAT was working fine for the the global pool, but the systems with static NAT could not get online. I tried lots of different things to fix them, and they never worked. Finally I rememberd running into an issue like this a long time ago, in that the static NAT IP's wouldn't work without giving them a bump-start on the network. So I assigned the ASA each of my WAN IPs, one at a time, and tested them all. After that I went back to the original WAN IP, configured the static NATs, and they fired right up. why did my static NAT entries not work until I first assigned them to the ASA, then swapped back? I did reset the DSL modem when I swapped the firewalls, so I don't believe it was an ARP issue (unless it was an ARP issue at the far end?) I would like to know if there is something I can do differently with the devices or with the config to not have this issue again in the future.
View 5 Replies
View Related
May 25, 2011
Currently a customer has all theLAN devices using a router as the Default Gateway. The router also do the Dynamic NAT to the internet access and has NAT/PAT rules to publish some services like HTTP and FTP. As I know the router will permit all the incoming traffic in all its interfaces without restrictions at less there is an ACLs that restrict the incoming traffic on an specific interface.Now the customer has bought a brand new ASA and wants to use it as the default gateway for the entiery LAN. This means, the ASA will have the internet connection and will be the responsible for the NAT/PAT process.
I have configured the NAT/PAT rules already following the current router configuration, but I need to know if I have to configure ACLs allowing the incoming traffic on th Outside interface for the services I NATed.
View 1 Replies
View Related
Jan 12, 2012
I have a Cisco ASA5505 running 8.2(1) and I am using ASDM to manage the firewall. I have a Linux VPN server on the inside with and IP address of YYY.YYY.YYY.39 with a static NAT to the outside with an address of XXX.XXX.XXX.171 . I have a site to site VPN tunnel which terminates on the outside of the ASA on the outside interface XXX.XXX.XXX.190 .Traffic from the YYY.YYY.YYY.0/24 network can't transverse the site to site VPN as there is a conflict of IP address's on the far side so it is natted via a dynamic policy to host address ZZZ.ZZZ.ZZZ.100, Users remote into the inside(YYY.YYY.YYY.0/24) for support via the Linux VPN server (.39) and then need to communicate down the site to site VPN. The problem is that the static NAT for the incomming connections takes preference and bypasses the site to site VPN tunnel for outbound traffic. I tried to create a policy Static nat but it tries to modify the static nat that handels the incomming traffic to the Linux server.
View 2 Replies
View Related
Jan 28, 2013
i have 2 internal server sitting in inside interface
inside network vlan 1 ip address 192.168.0.20, and 192.168.0.22
i going to map 192.168.0.20 to public ip routable address 203.117.124.180 and 192.168.0.22 to public ip routable address 203.117.124.181
the purpose is to make those 2 server 192.168.0.20, and .22 to be able to access remotely using public routable ip address,
however, after done the configuration i still not able to ping or access the public IP Address mention above. my both server are turn on and can access internally.both server are also able to access internet. See below partial configuration retrieve from Show Run.
nat-control
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
nat (Antlab) 1 0.0.0.0 0.0.0.0
[Code].....
View 2 Replies
View Related
Aug 30, 2011
I have a 5505 for a small business that has one web server. The web server has a static NAT entry to an IP address and not an interface. There is an access rule allowing any HTTP traffic to the outside IP of the web server. From the web server I can't access the Internet.
All other computers on the network can access the Internet using a dynamic nat rule that uses the outside interface. The web server is accessible from a computer behind the firewall.
If I delete the static NAT entry for the web server I can get on the Internet.
I have turned debugging on and see that an outbound connection is built and then 30 seconds later the connection is torn down with the bytes 0 SYN Timeout message.
I am running 8.0(5).
View 3 Replies
View Related
Aug 31, 2012
I have an ASA 5505 behind my internet router. i have got only one public ip configured on the router outside interface.192.168.20.0/24 subnet is configured between ASA and router and inside network is 192.168.10.0/24 (Refer the attached diagram).
I have exposed my mail server and ftp server to public through static PAT in router and ASA with the same public on router outside interface. Iam facing issue some of the machines inside my network internet is not working(actually DNS is not resolving) some of the PC's internet is working fine some of the PC's randomly working. i have attached the diagram and ASA config , after this issue is sorted out i need to configure a L2L VPN to my head office.
View 8 Replies
View Related
Feb 5, 2012
I'm trying to configure a second server on my network but whenever I add the static NAT rule, the internet stops working on that computer.
Here's my Cisco ASA configuration:
ASA Version 7.2(3)
!
hostname domain
[Code].....
View 16 Replies
View Related
Feb 9, 2013
I have configured the ASA in a very similar manner to how the PIX was set up but I'm having trouble with some hosts on the inside accessing the Internet. Any inside hosts which use DHCP work fine. Any inside hosts with a static IP (and configured on the ASA with a "static" rule) cannot access the Internet. For example, in the config below the server daviker-dialler cannot access the Internet. I've spent a few days working on this now and have started from scratch several times but I'm not getting anywhere. Apologies for all the X's everywhere, didn't like to post anything sensitive on the Internet.
View 2 Replies
View Related
Jun 10, 2011
I am setting up a Cisco ASA 5505 first time for My organisation, I usually setup Cisco Router, I have 10 Static IP, & Have 6 Server (S-1, S-2, S-3, S-4, S-5, S-6), Traffic Should be pass through the ASA and is distributed to the destination server that is specified in the packet. LAN servers can be separated into discrete networks for security. For example, a private LAN for internal traffic accessed only via remote dial-in VPN sessions and Want to Configure DMZ for Server (S-4, S-5, S-6) that allows public web traffic.
I have Attached My Network Diagram I have some question,
1:- Can we Configure Multiple Static IP On ASA 5505 ?
2:- If Diagram is wrong what change need to be done ?
View 2 Replies
View Related
Feb 3, 2013
I have ASA 5505 with basic licence, v9.1, ASDM 7.1. I want to create the DMZ for a web server.
The interface 0 is for the outside network The interface 6 is for the DMZ All other interfaces are for the inside network
My ISP provided me with one public static IP address, one gateway address and a subnet mask 255.255.255.252
1/ I would like to ask which interface I should assign the public static IP address to. Should it be assigned to the outside interface 0, or should it be assigned to the DMZ interface 6, while outside interface would be configured to use DHCP?
I tried to assign the static IP address to the outside interface first, but then when I used ASDM the “Public Servers” feature to configure NAT, I get error message that the outside interface and the public address cannot have the same IP address.
2/ For the sake of peace of mind, I am thinking about using the second firewall, which would be used only for the inside network. Can I connect this second firewall to one of the inside interfaces of the 1st firewall,
View 4 Replies
View Related
Mar 22, 2012
I have created a simple static ip address by using this command:
interface Vlan1
nameif inside
security-level 100
[Code].....
But, no matter what, the I can't ping the static address or access the computer 10.2.1.2 from outside of the asa 5505. I have attempted to ping from inside of the asa 5505 or from another computer. I just does not work.
I also have created several rules that allows icmp traffic.
icmp unreachable rate-limit 1 burst-size 1
icmp permit any echo-reply inside
icmp permit 10.2.1.0 255.255.255.0 inside
icmp permit any echo-reply outside
icmp permit any outside
View 1 Replies
View Related
Mar 20, 2012
I just upgraded my firewall to ASA 5505. Now, my original static ip address cofiguration is gone. Apperantly, Cisco went away from static ip address to something like nat (inside,outside) dynamic interface. how to create a static ip address under version 8.4? By the way, I am sharing what my configuration used to look before upgrading.
!
hostname cisco-asa
domain-name default.domain.invalid
names
!
interface Vlan1
nameif inside
security-level 100
[code].....
View 7 Replies
View Related
Feb 23, 2013
I was checking out the config on my ASA and noticed a bunch of static routes configured when I did a show route. With the exception of two that I expect to be there, the remainder point traffic destined for specific internal hosts to the outside interface, i.e.
S private_ip 255.255.255.255 [1/0] via public_ip, outside
I verified that I cannot ping those hosts from the firewall. I logged in to the ASDM. When I check the Configuration>Device Setup>Routing>Static Routes it only shows two static routes, the ones I expect to see. If I look under Monitoring>Routing>Routes, I see the same output as I did on the CLI. I looked around to see if I was missing a key location for this information, and I was able to see the same static routes output in Monitoring>Routing>Routes. Since this is under monitoring though there's no way to delete these routes, and I still don't know where they were configured originally. Then I happened to check under Monitoring>VPN>VPN Statistics>Sessions, and I see several of the private IPs used in the static routes being used by VPN users, including my own! I know I didn't assign myself a static IP for VPN use or anything like that. So, what are these static IP routes? Why do I see them in the CLI and not under the Configuration tab? I mean, I know I can delete them from the CLI but I'm trying to figure out why the info is not synced. Am I seeing dynamically created content based on the VPN connections?
View 2 Replies
View Related
Mar 17, 2012
working config with least amount of code for:
IOS post 8.3
Subnet: 192.168.1.0 /24
Static NAT (from any source) to server 192.168.1.100 and allow the same incoming connections on outside interface
Ports:
TCP 20,21
TCP 80
UDP 50000-50020
View 1 Replies
View Related
Sep 20, 2012
I have been using static NAT to map between a single server behind an ASA 5505 and a single public IP address. In other words, I've been doing this:
object network NAT_ME
nat (inside,outside) static interface
Now I would like to start using the clientless VPN feature of the ASA, so I of course don't want that particular port forwarded to the server. Is there a way to define such an exclusion? I've tried several things, including setting up a separate NAT rule to direct that port back to the ASA's interface, without luck.
If that is not possible, what configuration would I need to move to in order to get the behavior that I want? It is important that all (non-VPN) traffic is passed exactly as it arrives at the firewall (whether it is coming from internal or external), with the exception of changing the IP address (i.e., I need static port mappings for some of my services).
View 5 Replies
View Related
Aug 15, 2012
I am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
View 12 Replies
View Related
Dec 18, 2011
We're getting "Connaction Timeout / Connection Failure" error messages several time per day. Here is our setup:
Verizon FiOS Internet (ONT Box) --> Cisco ASA 5505 --> EdgeMarc 4500 Router --> Cisco 300-24G Switch --> Dell PE1950 Servers
From past few months, we keep getting Connection Timeout and Connection Failure error messages in our vendor application which connects to SQL Server 2005. Also Terminal Server 2003 keep disconnecting for every few hours.After several days of troubleshooting, we come to know that this Cisco ASA 5500 is not working properly. When I access the ASDM, it shows several warning messages.I know there is a setting option to configure TimeOut, but is there anyway to test and track the ASA 5500 regarding this Timeout issues?
View 3 Replies
View Related
Jan 29, 2012
how to open a site by using static ip address
View 2 Replies
View Related
Jun 1, 2011
Half of the time i have to stay at hotel due to business trip. The hotel i stay will provide free internet broadband with cable but no WIFI. Can i set up WIFI if i have router?
View 2 Replies
View Related
Feb 13, 2012
I have the asa 5505 with asdm 6.4(5). my inside LAN is 192.168.0.0/24. the outside of asa is connected on lan 10.13.74.0/24 and i need over LAN 10.13.74.0/24 connect on LAN 10.15.100.0/24. i put nat rule on asa 5505 and acl rule and users from lan 10.15.100.0/24 can connect on my server, but i can't connect on from inside of asa connect on lan 10.15.100.0/24 and 10.13.74.0/24. my configuration asa is Result of the command:
"show running-config"
: Saved
:
ASA Version 8.4(2)
!
host name Cisco asa
enable password 8Ry2YjIyt7RRXU24 encrypted
password 2KFQnbNIdI.2KYOU encrypted
names
[ code]....
what i do that connect on LAN 10.15.100.0/24. i cant ping my outside interface, put rules on acl, i enabled service policy rule for icmp ,but nothing.
View 3 Replies
View Related
Mar 1, 2011
How to share reliance broadband connection between two pc's using hub or direct line in one computer have windows 7 ..
View 1 Replies
View Related
Feb 15, 2011
We recently got a 10 meg dedicated internet fiber connection installed. I connected it to a PIX 501 firewall and everything worked fine (I tested it for a couple of weeks). A couple of days ago I got a new ASA 5505 and replaced the PIX with this device. It works, but every so often there seems to be a timeout when surfing the web whereby I click on a link and there is up to a 45 second wait and then the page loads quickly. I was not getting this before on the PIX so I'm assuming it's not a latency issue with the connection. I am the only one using this connection on the network so it's not to say that it's being bogged down. I want to roll this out to the other users on the network but not when this is happening. The configuration is below:
: Saved
:
ASA Version 8.2(1)
!
hostname ciscoasa
[Code].....
View 8 Replies
View Related
Apr 15, 2013
I have a SIP trunk in my Florida office connected to a Cisco 2851 ISR. I'm using Unified Communications Manager 8.0 and life is great.
We just opened a new office in Spain and now the fun begins. We created a site-to-site VPN tunnel using ASA 5510 in Florida and ASA 5505 in Spain. We can register IP Commuicator phones in Spain but when they make calls it shows up as a Florida call. We need it to show up as a Spain call.
We are thinking to get a SIP trunk into the Spain office but I only have a ASA 5505 over there. Can I terminate a SIP connection to it? Is this the best option? If not, what is the recommened setup?
View 1 Replies
View Related
Nov 13, 2012
I am having a problem with a ASA 5505. The users on the inside cannot access internet for the most of the time. When i looked over the configuration and tried a few changes i got out to internet about 5 seconds every 30 minute or so. Very strange. When i try to access internet i just get the windows post that DNS is not working properly. As you can see in my config i get all addresses dynamic from ISP.
I am not sure what to do next, i tried to set static routes, make Nat changes, static dns addresses, searching this forum but nothing works. It seems like there is a ISP problem but i have talked to the support twice today and they say that all is fine from their side. Does ASA behave like this?
ASA Version 8.2(2)
hostname ciscoasa
domain-name
enable password encrypted
passwd encrypted
names
[code]...
View 7 Replies
View Related
Jun 23, 2012
I have a Cisco ASA 5505 - 50 VPN edition. I have baffling network issues that I have not been able to pinpoint and I recently started to think it may have something to do with my ASA. I'm a network administrator and I have a Cisco ASA 5505 in my home network so I can learn how to manage Cisco ASA's and utilize the Easy VPN feature so I have a always on VPN connection into work to log into servers, etc. I've been using the ASA for almost 6 months with the EasyVPN feature with no issues. My ISP is Comcast.
Within the last week my connections have been randomly dropping for about 20 seconds and then reconnecting. I have two computers on the network that have a direct ethernet run to the switch ports on the back of the ASA. When the connection drops, I see my LAN icons completely lose connectively (yellow exclamation warning) then after 20 seconds, reconnect. This is very random. I was able to get it to happen every time I connected to XBOX live and play a online game. It would almost on cue drop after 30 minutes of online gamming. Here are the steps I have taken:
1. Replaced 10/100 switch to a brand new 10/100/1000 switch from computer run in my office to the ASA.
no joy
2. I upgraded the ASA to the most recent firmware: ASA Version 8.4, ASDM Version 6.4
no joy
3. I had an ethernet run under my carpet to the office, I started to think that maybe one of the cables had an issue after walking on it and vacumming causing a short. I removed all the ethernet under the carpet and installed power line over ethernet adapter from the ASA to my office.
no joy
4. I checked both computers on the network for viruses. All computers came back clean after scanning wth Malwarebytes and SuperAntispyware.
5. I've watched the logs on the ASA as the LAN connection drops and I don't see error messages to troubleshoot this issue.
The only thing left to replace is the Comcast modem or the Cisco ASA. The Comcast modem is newer and only about 1 year old (rented from Comcast). Since my actual LAN connection drops and I lose connectively I believe there may be some issue with the ASA or the ASA switch ports or some sort of internal hardware issue on the ASA.
View 4 Replies
View Related
Jun 24, 2012
I'm trying to get an asa5505 set up so that our web server can send an LDAPS login to a client's server and receive the request back. The default IP our traffic goes out on is different than where I want the connection to come back in on. So, I set a NAT rule to send all traffic from a specific inside IP out a default outside IP. I also allowed LDAPS traffic from the client's server IP address in and have nat'd it back to the appropriate inside IP address. It seems to build the outbound connection fine, but then seems to drop it right away, which then seems to not allow the response back in. I've attached a picture of the log, with (what I think are) the lines in question highlighted. I'm far from a routing expert, but this seemed like a fairly easy setup.
View 1 Replies
View Related
May 23, 2012
I have a simple network with an ASA5505 mainly used for AnyConnect so there is little traffic. There is 1 laptop connected to the E0/1 of the ASA and then E0/0 is going to the internet port. I've noticed about ever 15-20 minutes, I lose all connection. The laptop can no longer browse the web and handsets can no longer VPN into the network. I've noticed a few seconds after performing a clear arp, all the connectinos are restored. The laptop can browse the web and handsets can VPN in again.
View 11 Replies
View Related
Feb 27, 2011
I have asa 5505 with security plus license, I configured dual ISP with two different ISP provider. I followed below cisco document to configure dual ISP [URL] The Configuration works during the testing, while removing the primary ISP cable from firewall. The problem i am facing is my primary ISP is down but the gateway is still up and it not switch over to backup ISP. For SLA which IP should i monitor so once my primary ISP is down it will fallback to Secondary.
View 5 Replies
View Related
Oct 6, 2011
I configured an ASA 5505 a couple of weeks ago. Every thing is working properly except it sends irritating messages to the syslog server. Her is an example of the message:
%ASA-2-106001: Inbound TCP connection denied from 195.215.221.56/80 to 10.70.13.90/252 flags PSH ACK on interface outside
%ASA-2-106001: Inbound TCP connection denied from 195.215.221.56/80 to 10.70.13.90/2252 flags ACK on interface outside.
View 1 Replies
View Related
Feb 27, 2011
I changed a configuration and suddenly I lost the internet connectivity... Result of the command: "show running-config"
: Saved:ASA Version 8.2(1) !hostname ciscoasaenable password qVQaNBP31RadYDLM encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 !interface Vlan2 nameif ATT security-level 0 pppoe client vpdn group ATT ip address pppoe setroute !interface Ethernet0/0 switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!ftp mode passiveclock timezone EST -5clock summer-time EDT recurringsame-security-traffic permit inter-interfaceobject-group service DM_INLINE_TCP_1 tcp port-object eq ftp port-object eq ftp-data port-object eq wwwaccess-list ATT_access_in remark Linkstation Accessaccess-list ATT_access_in extended permit tcp any host 99.23.119.78 object-group DM_INLINE_TCP_1 access-list ATT_access_in remark Linkstation
[code]....
View 3 Replies
View Related
Apr 26, 2011
To sum it up the ASA is maxing out at 7MB down on a 25MB connection. The connection was tested with the ASA removed and the connection is fine.
This popped out at me the most but i'm not sure what it means:
12884935775 switch ingress policy drops for eth 0/0
[code]....
View 6 Replies
View Related
May 24, 2012
One of our hospitals keeps reporting that their internet is going out for a while than comes back up, sometimes they even have to reset the ISP modem for this it to work again. I upgraded and switched ISP to Time Warner Cable and figured it would essentially solve the issue, but there are still reports of internet outage and our new ISP has confirmed multiple times that their end is still up. Our ASA 5505 was configured by a previous employee, but when looking at the running config I noticed that the Interface for our ISP is NOT set to Duplex Full and Speed 100.
interface Ethernet0/5
switchport access vlan 2
View 3 Replies
View Related
