Cisco Infrastructure :: IOS Router 2600 - ARP Failed / TFTP Transfer Aborted
Apr 24, 2011
IP_ADDRESS: 10.10.10.1
> IP_SUBNET_MASK: 255.255.255.0
> DEFAULT_GATEWAY: 10.10.10.10
> TFTP_SERVER: 10.10.10.10
> TFTP_FILE: c2600-js-mz.122-15.T16.bin
> ....
> ARP: ADDRESS RESOLUTION for 10.10.10.10 timed out
> ARP failed with failure code 1. TFTP transfer aborted.
I connected cross cable between router and my pc and i put image of router in tftp_file with tftp server so when the router wants confirm y or n and i make y so my connection area connect and disconnect and never make connection with router so how can i slove it what are the steps in my pc and the router i used solarwinds tftp server ...
View 3 Replies
ADVERTISEMENT
Dec 2, 2011
How i can transfer the router logs to email address.Wev are using the router 2600.
View 5 Replies
View Related
Oct 3, 2012
I have Cisco 2600 series Router which has only 32 MB flash memory. I tried to load IOS image in that but image size is 29 Mb in compressed form. The minimum i found is 5 MB in compressed form but it is missing so many commands. that in 32 MB flash, how can I load image which has almost all the commands.
View 3 Replies
View Related
Nov 8, 2012
I'm trying to upgrade my 2950G-24-EI via tftp but it looks like the sw can't transfer any of the files completely or with errors. I downloaded the BIN+TAR files from Cisco (and from another site) matching my Catalyst and opened an TFTP server on my PC. The files are :
c2950-i6k2l2q4-mz.121-22.EA14.bin
c2950-i6k2l2q4-tar.121-22.EA14.tar
[code].....
View 6 Replies
View Related
Apr 3, 2013
In the process of upgrading the image for all of our floor switches..In total there are 35 WS-3560G-PS switches.
So far I have been upgrading them all to image c3560-ipbasek9-mz.150-2.SE2.bin and that has gone well.
But this eve 2 of the switches are extremely slow on the TFTP transfer. Duplexing and links are good back to core.
But when I do a sh ver to compare one switch that is good and one that isnt I noticed this
TFTP Transfer is good on this one - cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
TFTP Transfer is slow on this one - cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 131072K bytes of memory.
View 2 Replies
View Related
Apr 12, 2012
I need to transfer a config from a TFTP Server to a 4507 and a 6513. When I transfer the config to both those switches, does it require a reboot?
View 5 Replies
View Related
Jun 8, 2012
Is there a possibility to transfer files between two N5k's via mgmt0 using TFTP protocol?
Source: One N5k's mgmt0 interface
Destination: Another Nk5' mgmt0 interface
I know when issuing "copy bootflash tftp" or vice versa, I need to specify management VRF. But how do I specify to be TFTP itself sourced from mgmt0 interface in NX-OS? From IOS I was used to use "ip tftp source-interface <interface>", but in NX-OS I have only Ethernet or Loopback as an option.
According to NX-OS Unicast Routing Configuration Guide (Configuring Layer 3 Virtualization) the answer should be in N7k configuration guide, but I didnt find it there either...
View 1 Replies
View Related
May 29, 2012
I am doing image upgrade on Catalyst 6509-E. During TFTP image transfer to sup-bootflash I always see !!!!!!!!!!!!!!!!!o!!!!!!!!!! "o" out of sequence packet. Although the image size seems to be correct at the end but there is always some "o" packets.
I am assuming not, but I haven't tried loading with the image after seeing this.
View 2 Replies
View Related
Dec 17, 2012
i have few catalyst switches (2960, 3750) and i can't upload to them any files by tftp from my laptop, but i can download from them, and this bug don't appears on two routers.I was change tftp server, type of connection (wifi, cable), turn off firewall on win7, but no dice.
View 2 Replies
View Related
Mar 11, 2003
I need to do one Catalyst 5500 as a TFTP server.Can I do it?Is the catalyst available to be a tftp server?
View 4 Replies
View Related
May 24, 2012
I have a Cisco 831 router (c831-k9o3y6-mz.124-5c.bin) that cannot backup the config to a local tftp server. I have seen this behavior on a few different Cisco devices over the years and have never found a solution. The connection is made to the tftp server (in this case tftpd but similar behavior on any tftp server) and a blank file is created on the target machine file system, but the data is never transferred.
The router shows %Error opening tftp://192.168.0.2/router-confg (Timed out) [Failed]
The tftpd log shows 5 repeated attempts at the file write.
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:40.922]
Write request for file <router-confg>. Mode octet [25/05 11:56:40.922]
Using local port 61607 [25/05 11:56:40.922]
<router-confg>: rcvd 0 blk, 0 bytes in 3 s. 0 blk resent [25/05 11:56:43.922]
Connection received from 192.168.0.1 on port 53570 [25/05 11:56:43.923]
[Code]...
This is also stopping me upgrading the image on the router as I cannot transfer in the other direction either.
View 1 Replies
View Related
Oct 5, 2010
I have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
View 25 Replies
View Related
Aug 28, 2012
I have a 2600 router i intend to use as an access server. I doesn't have an IOS so i downloaded via tftp. I should see the file at Dir flash:, but all i get are these error
rommon 1 > dir flash:
File size Check sum File name lseek out of bounds getdirent: lseek error rommon 2 >
And if i tried to download again the file, its failing because it seems that there aren't any space available in my flash. Here is the mem info.
rommon 2 > meminfo
Main memory size: 64 MB.
Available main memory starts at 0x10000, size 65472KB
IO (packet) memory size: 0 percent of main memory.
[code]...
Here's what i think. The first file download could be corrupted and it eats up the space on my flash. My question is how can I reformat the flash so that I can re download the IOS? And if in case that fails also, any other way i can recover this machine.
View 4 Replies
View Related
Aug 30, 2012
I bought some hardware and created my own lab to prepare for the CCNA. I only have one machine with a serial port and whenever I try to connect to a router (I've tried multiple purchased from different sources) nothing happens on the screen. If I wait for a couple of seconds and hit enter I get the response shown on the screen in the screenshot I have inserted. If this image is too small I have also attached. looks like it has already asked me this but I am unable to see it. Shouldn't I see some information when I attempt to connect, some acknowledgement that I have connected? I have tried using both hyperterminal anbd PuTTy.
View 1 Replies
View Related
Nov 29, 2011
I am facing an issue with several ACS appliances (some other work well) when upgrading to version 5.2.0.26.8.
When I launch the command acs patch install, I receive the following error message (we use FTP):
Failed to copy file '5-2-0-26-8.tar.gpg' from repository PatchRepository
(Error -302)
% Error: patch install 5-2-0-26-8.tar.gpg from repository PatchRepository - transfer failed (code 1)
This happens on three appliances but I could successfully upgrade 4 other appliances.
What is the reason behind this error code ? What could I do solve it ? I have already tried to create another repository on another server, without success.
View 5 Replies
View Related
Dec 10, 2012
From 6.0.199.4 to AIR-CT5500-K9-7-3-101-0.aes. Get the error below halfway through download of file to controller.
*Dec 11 14:18:55.775: %UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:4158 Error FTP file Transfer [ftp_get], <28>, No space left on device.
I have no idea how to delete files form the storage on the 5508? TFTP transfer gives me this error after the upload is done:
% Error: Code file transfer failed - Error while writing output file
*Dec 11 15:11:45.514: %TFTP-3-FILE_WRITE_FAIL: tftp_client.c:517 Error while writing 512 bytes to file. Tftp error.
*Dec 11 15:11:45.514: %TFTP-3-WRITE_NOCLOSE_FAIL: tftp_client.c:147 Error while writing the local file: No space left on device
*Dec 11 15:11:45.514: %OSAPI-3-FILE_WRITENOCLOSE_FAILED: osapi_file.c:582 Failed to write 512 bytes (FileDesc:64). file write no close failed
View 6 Replies
View Related
Dec 19, 2012
I am running 12.3(11) T8 on Cisco 2821 platform and trying to upgrade to 15.0. No luck. So I tried to upgrade it to 12.4 24T. But failed several times on different routers. Is there an intermediate version I should land before jumping to 12.4 24T?
View 3 Replies
View Related
Oct 23, 2012
Having troubles loading a certificate in System security/802.1X Supplicant. I tried to upload *.car and *.msc certificates, but the device aborted the upload at each attempt.
View 2 Replies
View Related
Mar 6, 2011
I'm having trouble TFTPing a configuration from my 851 Router to my computer through a IPsec VPN tunnel that this router is connected though. I am able to telnet and ping all devices on the far-end with no problem. I can TFTP a config from a switch behind this router, no problem. I am guessing this problem is related to an ACL on the router. I am also having trouble connecting to this router using the Cisco Config Professional. Discovery will fail, with connection could not be established or HTTP service is not enabled. I have enabled HTTP service. The CCP works fine when I am on the router's subnet.
View 3 Replies
View Related
Jul 19, 2011
I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies
View Related
May 30, 2006
I just have a quick question about the TFTP utilities that Linksys has. I tried to upgrade the firmware of my BEFSR41 v1 router using the TFTP utility for a BEFSX41 and it didn't work(I just hope I did it correctly).
So, the question is, are these utilities router-specific or they should work with other routers as well?
View 5 Replies
View Related
Sep 27, 2011
I have a 2801 running c2801-spservicesk9-mz.124-3g.bin According to the Cisco IOS MIB locator the image supports OLD-CISCO-SYSTEM-MIB I have tried .1.3.6.1.4.1.9.2.1.55 etc to set server IP address and the filename string but without any luck.e.g.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.2.1.55.a.b.c.d (where a.b.c.d is the server IP)
I have also tried the method similar to that for Cat 3550 switches where you create a table of entries to define the transfer paramaters then activate the transfer (I think the CISCO-CONFIG-COPY-MIB)
e.g.
[URL]
C:>snmpset -v 1 -c private <device name> ccCopyProtocol.<random number> integer 1 ! 1 = tftpccCopySourceFileType.<Random number> integer 1 ! 1 = networkFileccCopyDestFileType.<Random number> integer 3 ! 3 = startup & 4 = runningccCopyServerAddress.<Random number> ipaddress "<server ip address>"ccCopyFileName. <Random number> octetstring "<file name>"ccCopyEntryRowStatus.<Random number> integer 4 ! 4 = createAndGo, or 1 = Active
To write net have the source as running (4) and the dest as network (1)
ccCopySourceFileType.<Random number> integer 4
ccCopyDestFileType.<Random number> integer 1
Clean up at the end - destroy .14 with the value of 6.
example output : -
-- earlier output omitted --
Error in packet.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.4.111
Error in packet.
[code]...
View 4 Replies
View Related
Apr 10, 2012
I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
View 1 Replies
View Related
Jul 13, 2011
I have a cisco 877 router connected to our adsl broadband at our head office. I have managed to set this up with Nat and DHCP all working to let multiple users access the internet through our single static ip supplied by the ISP lets say the ip is 1.2.3.4.Our internal network is 192.168.1.0 255.255. 255. 0.I have a draytek vigor 2600 at a branch office set up the same with a static ip addresss supplied by the ISP lets say the ip is 5.6.7.8.The internal network is 192.168.4.0 255.255.255.0
I am trying to set up a VPN between the head office and branch office so the branch office users can connect to our internal server(lets say ip is 192.168.1.2) to receive group policies,access files and also telnet into our database server(lets say ip is 192.168.1.3).I have attached a sort of running config that i have pieced together from bits i have read on this site and others. I have tried these settings and other permutations of these settings but i cant seem to establish a tunnel even though when i show int tunnel0 on the router it says tunnel is up and line protocol is up, if i show ip route it shows that there is an ip address for the tunnel and that is about it(No vpn light on).
If it makes sense and that I have entered the right information? I have highlighted the parts i am not sure about in red(Quite a bit and obviously not the exact settings but what i think it should be). Once all the settings are correct on the cisco will it automatically establish the vpn or do i have to dial it from the draytek.
View 4 Replies
View Related
Mar 4, 2012
i want to configure the router for internet access for hosts this is the my pub ip x.x.x.174 and mask 255.255.255.252 this is isp given subnetmask internal ip range is x.x.x.20-x.x.x.254
View 1 Replies
View Related
Jun 20, 2012
I have 3 Cisco 2600 routers with the same IOS and memory.One of them has CME...
What would be the best way to copy the CME from the one router over on the other two?Backup my FLASH to my TFTP and then restore to the other two routers?
View 1 Replies
View Related
Jan 19, 2012
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies
View Related
Dec 29, 2012
How to know the serial 0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 12 Replies
View Related
Apr 11, 2006
How to know the serial0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 4 Replies
View Related
Jan 11, 2012
I have cisco 2600 router. The problem is my router ios has been crashed and i unable to use any mode on my router. I need to install new ios. How can i install or upgrade new ios step by step.
View 1 Replies
View Related
Jan 16, 2013
Currently I'm using Cisco VPN client software to connect to a remote IPSec server on the workstations. I want to to configure IPSec client on Cisco 2600 router which connects to the remote IPSec server so the workstations can access VPN subnet without using VPN software. how to configure IPSec client on the router?
View 20 Replies
View Related
Jul 23, 2012
We have an old Cisco 2600 series router, running a single T-1 line, AT&T is the carrier. Very standard stuff.
The T-1 works perfectly on the old router. Cisco 2600 with a WIC-1DSU-T1 card. We have a brand new 2911 router with a VWIC3-1MFT-T1/E1 card in it. The circuit runs 100% clean and trouble free on the old router. When I plug it into the new router, it shows up/up but has a massive number of errors on the line, and the circuit is not usable. There are no timing slips or anything like that.
I have another site using the same router and card with the same configuration on that T-1 and it works perfectly. Zero errors. This site (in a different city) is totally slammed with errors. We already replaced the T-1 card and still have the exact same issue.
I've actually been doing this a long time, and I've tried all of the usual things, adjusting line build out, changing clock source, checking and re-checking configs. Nothing seems to reduce the error rate.
I personally think it has something to do with the Smartjack. Like maybe their LBO is too high or too low, and the old router card was more/less sensitive than the new one?
This is a layer 1 issue and is not defective hardware or defective configuration. I am looking for T-1 insights or bugs/issues.
View 1 Replies
View Related
Jul 11, 2011
I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports?
View 0 Replies
View Related
