I'm trying to upgrade my 2950G-24-EI via tftp but it looks like the sw can't transfer any of the files completely or with errors. I downloaded the BIN+TAR files from Cisco (and from another site) matching my Catalyst and opened an TFTP server on my PC. The files are :
c2950-i6k2l2q4-mz.121-22.EA14.bin
c2950-i6k2l2q4-tar.121-22.EA14.tar
[code].....
2950 switch has a IOS on flash , but i would like to set the swith like...
1. switch IOS to be loaded from TFTP server .if it fails
2. Loaded from local flash IOS1 , if it fails
3. IOS loaded from local flash IOS2.
does 2950 switch support this feature.
In the process of upgrading the image for all of our floor switches..In total there are 35 WS-3560G-PS switches.
So far I have been upgrading them all to image c3560-ipbasek9-mz.150-2.SE2.bin and that has gone well.
But this eve 2 of the switches are extremely slow on the TFTP transfer. Duplexing and links are good back to core.
But when I do a sh ver to compare one switch that is good and one that isnt I noticed this
TFTP Transfer is good on this one - cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 122880K/8184K bytes of memory.
TFTP Transfer is slow on this one - cisco WS-C3560G-48PS (PowerPC405) processor (revision F0) with 131072K bytes of memory.
I need to transfer a config from a TFTP Server to a 4507 and a 6513. When I transfer the config to both those switches, does it require a reboot?
View 5 Replies View RelatedIs there a possibility to transfer files between two N5k's via mgmt0 using TFTP protocol?
Source: One N5k's mgmt0 interface
Destination: Another Nk5' mgmt0 interface
I know when issuing "copy bootflash tftp" or vice versa, I need to specify management VRF. But how do I specify to be TFTP itself sourced from mgmt0 interface in NX-OS? From IOS I was used to use "ip tftp source-interface <interface>", but in NX-OS I have only Ethernet or Loopback as an option.
According to NX-OS Unicast Routing Configuration Guide (Configuring Layer 3 Virtualization) the answer should be in N7k configuration guide, but I didnt find it there either...
I am doing image upgrade on Catalyst 6509-E. During TFTP image transfer to sup-bootflash I always see !!!!!!!!!!!!!!!!!o!!!!!!!!!! "o" out of sequence packet. Although the image size seems to be correct at the end but there is always some "o" packets.
I am assuming not, but I haven't tried loading with the image after seeing this.
I'm trying to resolve an issue I'm having with connecting a WLC to the access points. I've inherited a net gear WLC and access points. Having redesigned the network and moving the WLC into the data center I am unable to connect to the APs. The APs are on 192.168.0.x addresses and the WLC is on 10.2.0.x address. I am able to ping to the closest switch (the one the APs are actually attached to) but not the the APs themselves.
All other devices are Cisco devices 4006 to 2950. So it goes WLC (10.2.0.33) - 4006 (10.2.0.23, 192.168.0.99) - 2950 (192.168.0.100) - APs (192.168.0.10 - 35). I have OSPF enabled, I am able to ping from the WLC to the 2950. So from 10.2.0.33 to 192.168.0.100, no problem with that. I try and ping from 10.2.0.33 to any of the APs ie 192.168.0.15 and it cannot find it.
I am using multiple cisco 2811, 3745 routers and 2950,3550 switches if I need to copy running configuration I have to go to each device and say copy run tftp: <address> Is here any way that automatically by schedule one a week or a month configuration copy from all devices to tftp server?
View 2 Replies View RelatedIP_ADDRESS: 10.10.10.1
> IP_SUBNET_MASK: 255.255.255.0
> DEFAULT_GATEWAY: 10.10.10.10
> TFTP_SERVER: 10.10.10.10
> TFTP_FILE: c2600-js-mz.122-15.T16.bin
> ....
> ARP: ADDRESS RESOLUTION for 10.10.10.10 timed out
> ARP failed with failure code 1. TFTP transfer aborted.
I connected cross cable between router and my pc and i put image of router in tftp_file with tftp server so when the router wants confirm y or n and i make y so my connection area connect and disconnect and never make connection with router so how can i slove it what are the steps in my pc and the router i used solarwinds tftp server ...
Bought a used 2950 for CCNA labs. I have no IOS and cannot get a successful transfer via xmodem. In ROMmon after the transfer completes text shows up as gibberish, commands seem to work. Text is normal after I reconnect. Dir flash: doesn't show any sys image, only a -rwx file. I have tried various IOS versions. This was purchased used, so it's possible it isn't working. This is my first time configuring a switch, I might have missed something simple.
View 5 Replies View Relatedi want to boot my Router's IOS from TFTP server but when I use the command: boot system tftp c2801-adventerprisek9_ivs-mz.124-24.T7.bin 172.16.10. 200; after that I write-mem, it shows the log:
-Router#wr
-Building configuration...
-ROMMON: out of room in table, cannot set "BOOT"
And when I reload the router, it cannot boot IOS from TFTP Server, sure my TFTP work well and 2801 can ping to TFTP.
How do i go about setting up a TFTP server from laptop to Cisco ws-C3750 48P Switch, I need to pull the image off the switch and place it on an other switch that has a corrupt image, The switch which is corrupted is the same as above Cisco ws-C3750 48P.
View 1 Replies View RelatedI have been looking at grading the IOS version on our 6509-E however there is not enough space on disk:0 to upgrade to the version I need to install. The question I would like to ask is - is it possible to boot the IOS from a TFTP server? If this is possible what configuration do I need on the 6509 to enable this. How does the 6509 know about the TFTP server as an IOS is not installed and therefore it will not have a network configuration
View 2 Replies View RelatedI am trying to create a backup of my 2620 router so I can use for GNS3.
I have only configured the IP address on my FastEthernet port. Having many issues with no connection to my pc, finally I found that you must enable the interface 'no shutdown'. Now I have a valid connection
I have made no other configurations on this router, everything else is default.
I can successfully PING from both ends
**PROBLEM: My problem is that when trying to 'copy flash' to my TFTP server, the response is**
".....
%Error opening tftp://192.168.1.3/c2600-advsecurityk9-mz.124-1a.bin (Timed out)
Router"
Is there another setting I should enable? Remember I have made no other configurations bar the ones above.
I am trying to copy IOS from unix box to 3750 switch
archive tar /xtract tftp://192.168.1.5/c3750-ipserviceslmk9-tar.122-55.SE7.tar flash:
%Error opening tftp://192.168.1.5/c3750-ipserviceslmk9-tar.122-55.SE7.tar (Timed out)
i get error
i can ping the unix box from the switch.Here is switch flash info
sh flash
Directory of flash:/
2 -rwx 6484 Mar 1 1993 00:02:53 +00:00 vlan.dat 4 -rwx 1929 Feb 4 2013 22:59:34 +00:00 private-config.text 5 drwx 128 Jun 22 1993 16:14:21 +00:00 c3750-ipservices-mz.122-25.SEE2 458 -rwx 20848 Feb 4 2013 22:59:34 +00:00 config.text 6 drwx 64 Jun 22 1993 16:21:05 +00:00 c3750-ipservicesk9-mz.122-35.SE2 460 -rwx 12961 Mar 1 1993 00:05:47 +00:00 config.text.bak 461 -rwx 3096 Feb 4 2013 22:59:34 +00:00 multiple-fs
15998976 bytes total (5166592 bytes free)
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error.I saw that this can be fixed with
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no service config
Switch(config)#exit
Switch#
00:13:47: %SYS-5-CONFIG_I: Configured from console by console
Switch#reload
I have done this 3 times to no avail.My TFTPd32 server on my pc is working fine.Here is the error
Switch#sh flas
Directory of flash:/
2 -rwx 556 Mar 1 1993 00:33:53 +00:00 vlan.dat
4 -rwx 3775 Mar 1 1993 00:37:54 +00:00 config.text
5 -rwx 24 Mar 1 1993 00:37:54 +00:00 private-config.text
6 -rwx 5687963 Mar 16 2007 01:05:23 +00:00 c3550-ipbasek9-mz.122-25.SEB4.bin
8 drwx 192 Mar 1 1993 00:04:40 +00:00 c3550-i9q3l2-mz.121-22.EA1a
[code]......
I have several SGE2000 in production and every night I save the current configuration to a tftf server... from time to time I get the following error: [code] Can't open TFTP client.At this time, the only way to be able to save the config again is rebooting the switch, but this is not a solution I am comfort.
View 5 Replies View RelatedI am trying to copy IOS from my TFTP server which is on my laptop to cisco 2960 switch
I am able to ping to switch from my laptop, connectivity is fine, tftp server is running
Current Image on Switch --> C2960-LANBASE-MZ.122-25.SEE3.bin --> trying to upgrade to --> c2960-lanbasek9-mz.122-53.SE2
I am getting below error when trying to upgarde IOS:
2960-SW#copy tftp: flash:
Address or name of remote host []? 10.1.x.x
Source filename []? c2960-lanbasek9-mz.122-53.SE2
[Code].....
how can i take backup of startup config to tftp server through tftpd server.I am using 4506e switch
View 2 Replies View RelatedI have a cisco 3750 swicth which i want to load a new ios to but unfortunately there's no enough space on the flash. This means that i need to backup the cureent (old) ios to my tftp server but the command keeps failing. It always gives 'No such file or directory' error .The free space on the flash is 8mb and my new ios is about 11mb.I also went inside the directory where the old is and inputed the same copy command but to no avail.Below are some of the command failure on the swicth:
[code]....
I recently posted this same issue the other day, using TFTPd32. Now i am pretty close to fixing it. I do have a different setup; my pc ethernet port is broken so I am using an ethernet/usb adapter. I am attempting to backup my IOS from a 3550 switch to my PC.
This is the error I am getting. Code...
I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies View RelatedOne of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
View 18 Replies View RelatedI have a server windows 2008 that I would like to have a nic teaming configuration, the server has two nics, each nic is connected to a different switch. One is connected to cisco 2960 and the other is connected to cisco 2950. I have read here in forums about nic teaming but using the same switch. I have not found using different switch. Is this possible?
View 1 Replies View RelatedI have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506. The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.Now i have the necessity to connect the 2950 to the other catalyst, 4506B. So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
View 8 Replies View RelatedI have a cisco catalyst 2950 switch (flash:c2950-i6q4l2-mz.121-22.EA1b.bin), in remote location with public IP,how to upgrade ios remotely, by that time running configuration will go?how much down time is required and ?
View 7 Replies View RelatedI have 10 2950 switches on my network that support only 64 vlans on each one. I actualy have requrement to cleate around 100 vlans acros them, can I switch off vtp and create required vlans manualy? I will have more or less following set up:
router
|
2950 - vlan 1,2,3,4,5,6,7,8,9,10
[Code].....
c2950-i6q4l2-mz.121-22.EA10a.bin is the image name of the 2950 switch i have in my office. what is the meaning of " i6q4l2 "? I saw some IOS like IP base, adv-security. but i didn't see anything like this before.
View 2 Replies View RelatedWhat are the security issues in connecting a notebook to a console of the 2950 switch? Can virus or Trojan enter into a switch during configuration session? If the answer is yes, what precautions must I take to prevent such case?
View 2 Replies View Relatedi am having 2950 switch. Now i login through telnet but as per the company standard i have to login through ssh. Is there any possible to enable the SSH in 2950. Any IOS supporting this operation.
flash:/c2950-i6q4l2-mz.121-19.EA1c.bin
After setting up the domain name I try to use the crypto key and it is no where to be located. Below is some of the information I copied from TeraTerm
Switch-1(config)#ip domain-name justin.lab.comSwitch-1(config)#crySwitch-1(config)#cry?% Unrecognized commandSwitch-1(config)#crypto key ?% Unrecognized commandSwitch-1(config)#crypto key ^% Invalid input detected at '^' marker.
Switch-1(config)#?Configure commands: aaa
5508 controller is at the headquarters which can be normally pinged, telnetted, http'd and tftp'ed....at the remote site, controller can be pinged and http'ed but cannot be telnetted and tftp'ed.there is a complete tracert from the remote site pc all the way to the controller.from a switch at a remote site, the controller can be telnetted. but from a pc on the remote site (which belongs to a remote site vlan), it is unable to telnet and tftp the controller.all active components can be telnetted from the remote site, such as the core switches and routers at the headquearters, except the controller.upgraded the controller code to 7.2.xxx in headquarters but still unable to telnet and tftp the controller from remote site.is there any more settings on the controller for telnet and tftp?what could be the problem why the controller is not available for telnet and tftp from the remote site?
View 12 Replies View Related