Cisco Switching/Routing :: Transfer Files Between Two N5ks Via Mgmt0 Using TFTP Protocol?
Jun 8, 2012
Is there a possibility to transfer files between two N5k's via mgmt0 using TFTP protocol?
Source: One N5k's mgmt0 interface
Destination: Another Nk5' mgmt0 interface
I know when issuing "copy bootflash tftp" or vice versa, I need to specify management VRF. But how do I specify to be TFTP itself sourced from mgmt0 interface in NX-OS? From IOS I was used to use "ip tftp source-interface <interface>", but in NX-OS I have only Ethernet or Loopback as an option.
According to NX-OS Unicast Routing Configuration Guide (Configuring Layer 3 Virtualization) the answer should be in N7k configuration guide, but I didnt find it there either...
I'm trying to upgrade my 2950G-24-EI via tftp but it looks like the sw can't transfer any of the files completely or with errors. I downloaded the BIN+TAR files from Cisco (and from another site) matching my Catalyst and opened an TFTP server on my PC. The files are :
I am doing image upgrade on Catalyst 6509-E. During TFTP image transfer to sup-bootflash I always see !!!!!!!!!!!!!!!!!o!!!!!!!!!! "o" out of sequence packet. Although the image size seems to be correct at the end but there is always some "o" packets.
I am assuming not, but I haven't tried loading with the image after seeing this.
I have two C2960 switches which have the management VLAN for other switches. These two switches are connected with each other via portchannel. Now the mgmt0 of few switches is connected to switch 1 and few other connect to switch 2.I have also connected the mgmt0 of switch 1 to an access port of switch 2 and vice versa.However in this set-up I am unable to reach switch1 via the mgmt0 IP address. However I can reach the mgmt0 Ip address of switch 2.I can also reach switch 1 and 2 via their int vlan IP.Has some one else experienced this and is their any specific reason why mgmt 0 IP address of switch 1 is not reachable.I have tried doing similar set-up on C3750, but have acheived same result i.e. I am unable to reach mgmt0 of switch 1.
> ARP failed with failure code 1. TFTP transfer aborted.
I connected cross cable between router and my pc and i put image of router in tftp_file with tftp server so when the router wants confirm y or n and i make y so my connection area connect and disconnect and never make connection with router so how can i slove it what are the steps in my pc and the router i used solarwinds tftp server ...
We are using HPUX server to collect files from switch to our server. Our server connect to cisco router and the cisco connect to X.25 protocol to communicate with switch. My question, how could i collect files from swicthes to our server and what is the command can i used ?.
This is some info about router.
'Serial0/0/0 is up, line protocol is up Hardware is GT96K Serial Description: LL018766 MTU 1500 bytes, BW 1544 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255
I'm trying to transfer my old files (pics, documents, music) from my 6 year old Macbook Pro to my new Windows 7 desktop that I built about a month ago. I'm having a really hard time getting the files to transfer over. I've tried extensively to network them through my home wireless to no avail. I tried setting up a workgroup and having my mac manually join to no avail. I know there should be a way to transfer these files quickly over my home network.
The real problem I am having is that my mac isn't showing up as a computer on my network on the PC. I can get the pc to show up as a computer on the mac, but it doesn't show my user profile and all the folders are empty. I've gone into the share settings on both machines and made everything as open and shared as possible, still not showing up. Any foolproof way to quickly transfer files between these machines?
i want to boot my Router's IOS from TFTP server but when I use the command: boot system tftp c2801-adventerprisek9_ivs-mz.124-24.T7.bin 172.16.10. 200; after that I write-mem, it shows the log:
-Router#wr -Building configuration... -ROMMON: out of room in table, cannot set "BOOT"
And when I reload the router, it cannot boot IOS from TFTP Server, sure my TFTP work well and 2801 can ping to TFTP.
How do i go about setting up a TFTP server from laptop to Cisco ws-C3750 48P Switch, I need to pull the image off the switch and place it on an other switch that has a corrupt image, The switch which is corrupted is the same as above Cisco ws-C3750 48P.
I have a D-Link Gigabit switch and I am trying to transfer files from my laptop (directly connected to switch) to my external hard drive (also connected to switch):The problem is that I get very slow speed for a transfer of a single file. It seems that the network utilization goes to 25%(normal) for just a few seconds and then it drops to 2-3%Please see attached image and propose what I should check.
I got a new laptop for Christmas and set up a new router which is working fine but now I can't access the laptop via the desktop. When I click on the laptop icon on the desktop network area windows asks for a username and password which I never set up and have no idea what the are. Any step by step guide to set up my network properly so I can transfer files back and forth.
First off, for almost ever my two computers (Laptop/Desktop) linked on the same network/home group have been able to transfer files to each other over without any problem. I must have done something when Norton Expired on my Laptop which is causing the problem now. (Both running windows 7)Both computers show up in the network tabs, as normal. From my desktop I can access my laptop like I always could. I can play movies etc. but I can't make any changes or transfer files. As it says "You need permission to perfrom this action."Now from my Laptop, I can also see my Desktop in the network tabs. but I can not view anything on the computer. When I try to browse through the network tabs, I get [Windows cannot access \network error code 0x8007035].
1. I had it working before so I know they are properly connected.
2. Both computers can see eachother
3. My Desktop can browse my laptops files (but not change anything)
4. My Laptop can NOT browse my desktop as it says the network error code
5. Neither Computer has a firewall on
6. Neither Computer is running antivirus software
7. In the Homegroup sharing tabs, both computers are marked as "allowed" in the media streaming options.
got a new laptop and want to move files from an old one.Both are on the same wireless network, with the old laptop with the files having Vista, and the new one has Windows 7.I tried right clicking a folder in Vistaand 'shared' it, but don't see it on the Win 7 laptop?
I was on vacation last week in Arizona.While there, I transferred my camera pictures to the hard drive. Meanwhile, i configured the laptop to shut down upon lid close. I had to go out for 4 hours and was in a hurry do just closed it. Apparently, it didn't shut down and the heat from the LCD screen radiated into the keyboard, overheating the video chip, frying it. Now I get just a white screen. I want to get my contents off onto a new laptop. VGA output doesn't work. How can I transfer files to new laptop without disassembly?
I have a laptop PC with WiFi, so I download a bunch of stuff on here. Then I have my beast/monster desktop gaming PC with a kick-ass geforce gtx 650 Ti, and an i7 processor, etc etc.... The thing it DOESN'T have is WiFi, or any internet capabilities at all (until I get a WiFi card in it or something).I have some 4 GB movies in my laptop, and so far what I been doing to transfer those movies to my desktop PC is saving it in a USB memory stick from my laptop, then taking the memory stick to the desktop PC and saving it there. I have regular Ethernet cables, would that work? What do I need to do to transfer files from my laptop to my desktop PC more efficiently and fast?
I have to transfer upto 50G of data over a Netgear 300 Mbps N300 router between too laptops both connected wirlessly to the same router. However, I get only 200 - 300 kbps when I transfer data? I get a faster speed when I download files off the web.
I have been looking at grading the IOS version on our 6509-E however there is not enough space on disk:0 to upgrade to the version I need to install. The question I would like to ask is - is it possible to boot the IOS from a TFTP server? If this is possible what configuration do I need on the 6509 to enable this. How does the 6509 know about the TFTP server as an IOS is not installed and therefore it will not have a network configuration
I am trying to create a backup of my 2620 router so I can use for GNS3.
I have only configured the IP address on my FastEthernet port. Having many issues with no connection to my pc, finally I found that you must enable the interface 'no shutdown'. Now I have a valid connection
I have made no other configurations on this router, everything else is default.
I can successfully PING from both ends
**PROBLEM: My problem is that when trying to 'copy flash' to my TFTP server, the response is**
I have a laptop I use at home and a mini laptop that I travel with. I record TV shows with the laptop and move them to the mini to watch them on the road.the programs are about 3 gb for a half hour show, 7 gb for an hour. I've been moving them one or two at a time on an 8 gb card, but that's kind of a pain. It takes 5 mins for each half hour show.I have a wireless home network, but that takes an hour to move one half hour show.Is there a faster way to move the files from one computer to another? Like ethernet cards or something?
I love sharing on my home network to transfer files from one computer to the next. However, I will soon have tenants in my house sharing my network ...so they can use my Wi-Fi to get on the internet.I need a solution to give them access to the internet without losing my own network sharing ability.I do not want them accessing my files.I have Windows XP home and a Dlink WBR-2310 router.As I see it, I need to either upgrade to a router with a Guest Zone/Access feature ...OR..upgrade to Windows 7(?) to give myself more networking options (i.e. file sharing where I select the users or set a password). Currently the XP permissions are too general.
I'm trying to transfer files from my wired desktop to my wireless laptop, and smaller files seem to transfer okay. Whenever I try to transfer a really large file, however, the internet and connectivity totally drops on my desktop (which is giving the file) and causes the laptop to lose the file. The desktop computer stays offline for about 1-2 minutes afterward before it either starts up again on its own or I reset the network adapter. I suppose it's important to note as well that the file transfer can fail at the very beginning, in the middle, or even at the very end, but my desktop computer always loses its connection whenever the interruption happens... but sometimes it can successfully get almost all the way through the file transferI tried following some of the steps in this case to confirm that I can ping and do all that jazz to my laptop and all of the services are running, since our problems seem similar. I've disabled all firewalls as well. However, since one computer is actually wired to the router, I don't think the solution will be quite the same
I have a small business network that connects 3 wired pc's and 2 wireless laptops. I am running a point of sale system on the network. I recently replaced the computer I use as a server. The work stations now run the point of sale system so slowly, they almost cannot be used. Both the wired and wireless systems are running slower. Both wired workstations are running Windows XP, both the old and new "server" are running Windows 7 64 bit. Both are Pentium dual core with 6gb of RAM. The old system has a Realtek RTL8168C network card, and the new system has an Intel 82579V network card. I replaced the computer due to other hardware issues. The cable used to connect it to the router is the same. The old machine ran the workstations MUCH faster. Does this have to do with the network card, or some other setting I am missing.I tried to make all the settings exactly the same so my point of sale system would still recognize the new computer.
Router: Linksys WRT54GL Main PC wired HTPC Wireless Win7
I am trying to transfer some blu-ray rips from the Main PC (wired) to the HTPC (wireless), but after 20-30 minutes it give me this error message and it can no longer locate the HTPC. i made sure the HTPC didn't so to "sleep" mode..
Something wrong with my home network or is it time to get a new router/adapter? everything else seems to work fine, except trying to transfer these huge files (10GB-20GB).
here is my setup:Old laptop with all my files is running Windows Vista.New laptop I got is running Windows 7.Both are connected on the same wireless network (same router and modem).I am looking for an easy way to copy and paste several folders and gigs worth of music, movies and photos to the new laptop with Windows 7. Is there a step-by-step guide on how to get these two laptops to recognize each other, and then access the files on Vista to copy and paste into Windows 7?
I have an issue that I'm not quite sure how to deal with. I had a media server die on me, so I built another one. It is built on Asrock A75 pro4 mobo. I am using the built in lan adapter from the mobo Realtek RTL8111E. At first I had a problem when no other PC could download anything from shares from the server. I could browse the files just fine, but when I tried download anything It would not start for a while and sometimes it would show speed of 16kb/s or something like that and would not budge after that. I re installed the driver did system restore and that partially solved the problem. Now all the pc's except one can download files fine. It is thru wireless network (server is connected with cable to router tho). The media server is running win7 ultimate the laptop that can't download the files is running vista. I tried using different wireless adapters with laptop and standing right by the router and it still wouldn't work. My old server ran also win7 and I had no problems transferring anything from it. I have another pc that runs vista and it doesn't have any issues. Internet works fine on that laptop and also it can download files from other pc's on network fine. The router I'm using is linksys e3000, though i don't think it has anything to do with the problem.
Actually the other pc's can't transfer anything either as of right now, so I would have assume the server is the issue
