PC Not Connecting On Initial Boot But On Restart It Does
Jan 15, 2013
My PC doesn't connect to internet on initial boot, says there is a disconnected cable. On a restart it finds the wirelss card and connects no problem to our BT hub. Tried disabling the wired option, tried a number of things around repairing links etc. but nothing works. it is annoying. PC spec below. Windows 7 is the OS
Giga byte mother board GA-Z68P-DS3
4x4gb of RAM
Intel i5 3.2 CPU
Radeon HD 6770 Graphics card
A wireless adapter TL-WN350GD
A 120 GB SSD hard drive
And a 1TB hard drive
A CnM card reader
Optical DVD drive too
I have this issue after Cisco send us RMA. Whenever i restart the AP, it wont able to auto boot. I have to type command manually to boot the AP. Is there any command or way to make this AP to auto boot?
Trying to get this linksys router working on my network. It is a wrt54gs. The machine that i'm configuring it with is running a 64-bit version of windows 7. I run the disc and it seems as if no matter what i try it will not connect to the internet. Can plug modem directly to pc and connect no problem. Can connect to router no problem. But cannot connect to the internet through the router.I made sure that ip addresses are assigned dynamically through dhcp and cloned the mac address of the pc i'm using to do the initial setup.
I have a DELL Desktop, and Window Vista Home Premium. My internet disconnects alone daily or 2 time daily, and I need to restart the computer to connect it again. I try to disability my Norton Security Suite, Diagnose and repair the Network, The 2 Network Adapters (Power Manager) are disables (the wireless, and the wire adapters)
I can start a console connection with my 2620xm, but the only output I get from the terminal software (Putty and Tera Term) is the character " ÿ " at all times even through bootup. For every boot up, I get an additional " ÿ ".I have Baud 9600, 8 bit, no parity, stop 2 bits, no flow.Is there something I am missing?
Recently I am having a problem during the initial start up. I am running Windows 7. After the computer starts up, I do not have an internet connection. The yellow triangle with an exclamation mark in it appears in the bottom right on the monitors. I can go to the internet connections and disable, then enable and my connection returns. This is only happening during the initial start up. This happens 3 out of 4 times during start up. I have had the cable company check everything and they are saying it is an issue with my computer.
I have a new Cisco ASA 5505 which I am trying to just setup so that all computers on the LAN can get to the internet (browsing and ping). My current setup attached.
On a recommendation from a network engineer, I got a used Cisco 891. Having worked with small business routers most of my working life, I thought this should not be a problem. However, I had no clue these things used a console and command line to initialize. I have the console cable, am able to console into the device, but am haphazardly issuing command lines straight out of the PDF manual but cannot get Cisco CP to discover the device.
From what I can tell, I am stuck at the point where the manual tells me to enable http server. I ran the command lines several times, executed write mem where available, but when I run the show services command, http is not enabled.
And if you do refere to command lines, I was reading some other forums and they were speaking of "run this command, run that command" but I could not make out the correct syntax, in what mode, whether it be config or config t, etc. So I might need a wee bit of handholding.
I'm hoping that once I can get Cisco CP or CPE to discover the device, I can make my way through the GUI to configure since those usually do make sense to me. As of now, I'm in the thick of it ...
I have a 2811 with CME 8.5; I recently added a SIP trunk and can make & receive calls just fine. I noticed today that when connecting to an external IVR system, I can't send additional tones (press 1 for Sales, for example). I have two DIDs, same provider, both doing the same thing. The config for one of my SIP trunk dial peer and translations are shown here - I think this is what's appropriate to review but can add anything else that's necessary. I've also omitted some dial peers for X11 and international dialing for brevity.
I'm new to using Cisco Config Professional Express but a lot of things are just "off" with this utility. But my problem for this post is specifically the 891W's internal access point, or initial access to it.
My situation is that I have some 891W's. It's my first time working with them, as well as with CCP Express (2.5). After isolating the router and my PC to their own network, using the IP my PC got via DHCP frmo the router I opened a web broswer and connected to the router. The initiial configuration wizard came up and I went through the various screens. One of those screens had basic config info for the internal wireless AP which I provided. Somewhere in that screen it asked for a Hostname for the AP, and a password. It doesn't askfor a username though. To ensure I wouldn't run into confision, I made sure to set every password I ever get asked to configure as the same thing so the AP's password was also the same.
However after I finish with the wizard, the java-based CCP Express begins prompting me for first the main router credentials which I provide and it gets the router config, then it prompts mefor the username/password for the Access Point. First of all, the initial config wizard had never asked me for the username for the access point, only the hostname, and the password. I had assumed it was just going to use the main router username, or perhaps a blank username.
In any case, nothing I type ever works. I've used cisco/cisco, or a blank username with my new password, or the same username as the main router with the password ---- nothing. This is now the 4th time I have completely Reset the router to factory defaults and while I am learning the use of CCP Express through repetition, I'd also like to get this thing configured and out the door so my customer can use it.
I am on version 8.2(1) of ASA Code.When accessing a SQL server on a secure internal interface,(Traffic is sourcing from DMZ) i'm getting some timeouts on the initial connection on port 1433. All subsequent connections work fine. Packet tracer shows the connection builds properly, and shouldn't have a connectivity issue. The problem server is a webserver that connects back through the firewall to access the SQL server on port 1433. We also have many other webservers in the DMZ which access the same SQL server, but do not have the same timeout issues. Here are my timeouts, from the config
I bought a Cisco 851W router from a coworker about a year ago and tried setting it up at my home with nothing but headaches. I finally gave up and went with DD-WRT and have yet to look back (my $40 router outperforms this thing on so many levels, but I'm getting off-topic!). I recently re-discovered this beast and pulled it out of storage to see if I could get a test network setup at home to practice on. I checked for any IOS updates and downloaded (and installed) the lastest image (c850-advsecurityk9-mz.124-15.T15.bin). I consoled in and verified the initial 10.10.10.1 IP was configured in the VLAN1 interface and directly connected a PC to one of the switchports and pulled a 10.10.10.2 address. I pull up SDM from my browser (I have used FF, IE, and Chrome, all with the same results. Java version is the latest, 6 Update 26.) and it launches the initial configuration wizard. I go through the steps and get up to the DHCP Configuration (after LAN, before Internet/WAN setup) and try to click Next and nothing happens. It doesn't freeze as I can easily go Back, but can never move forward beyond the DHCP configuration. Pressing Cancel on the wizard just shuts down SDM as a whole and exits.
In my troubleshooting steps, I did notice that as soon as I click Next in the DHCP configuration, nothing will happen in the wizard, but the SDM window in the background will automatically present the "Apply Changes" and "Discard Changes" buttons, which weren't there in the previous steps. Of course, neither of those are clickable due to the wizard being open. I really don't want to configure this thing from scratch using the CLI if I don't have to..is there ANY way I can bypass the SDM Wizard at all? Also, I'm running SDM Express, would downloading ASDM and trying to connect from there make any difference?
1. I couldn't telnet the switch after configuring. should i have to use cross cable or not to connect PC-PIX? (as new switches and routers run through straight cable). more importantly i couldn't even ping the inside ip which is telnet and ssh enabled.
2. Receiving the following after executing each and every command on global mode. -Configuration Replication is NOT performed From standby Unit to Active Unit -Configurations are no longer synchronized.
I'm trying to set up a new ASA 5510. I have a pretty simple set up with one /24 on the inside NATed to a DHCP address on the outside. Everything on the inside works and I can ping the outside interface from external devices. No matter what I do I can't get anything internal to route across the border to the outside and back. To try and eliminate ACL issues as a possibility I added permit any any rules to the incoming access lists on the inside and outside interfaces. Here's the sh run.
I have a new from the box 5508 which I am attempting to follow the initial setup process to IP it. When I make it through the initial setup the box reboots buts brings me back to the "terminate auto-install" prompt again for some weird reason?
I am interested in learning and setting up VPN IPSec with Cisco ASA 5505. I've managed to successfully setup VPN andcan connect to it from outside and browse securely to the outside/internet via tunnel. However, once I am connected to VPN, I cannot access any of my internal hosts/servers via VPN client. I am wondering it its a missing ACL/NAT...ASA Version 8.2(5)
I have manual Cisco 1812 (1811) Integrated Srvice Router Cabling and Installation in front of meI have Cisco 1811 connected to my laptop according to this manualI have Cisco SDM latest version installed on my laptopI have DHCP enabled on my laptopThe problem that my laptop can't get valid IP adreess from the router (see att. laptop_, laptop_2)
Which IP address I have to use in order to get access to router inrerface (see. SDM_1)?
We received an ASA5520-K8 through Cisco's Loan program so we could demo it as a replacement for our aging Cisco 3005 VPN appliances. Given that we are a non Cisco shop (except for specific appliances like concentrators and wireless access points), I don't have a great deal of experience with Cisco gear.I started to set to setup the appliance this morning but immediately ran into issues. The 5520 doesnt seem to be acting as a DHCP server, and worse yet, I can't access the unit even if I hard code the IP on the PC being used for configuration. I have to say that I feel kinda stupid having to post this, since I actually followed the documentation avaiable for this menial task and I fully expect the problem to be a simple one. Namely, I am using two specific sources of info for connections.
I've installed our previous WISMs and other WISM2s previously and never had a problem.
6500 running SXJ2. WISM2 running 7.3.101.0 (which is what the rest of our WISM2s are on)
Insert WISM and go through initial setup. Run a show wism status on the 6500, and show sysinfo on the WISM. All looks good. Service port and management vlans are up. From the 6500 I can ping the service port IP, but not the management IP. From the WISM I can't ping the managment default gw but I can the service port. Unable to get anything back from the GUI..not surprising as not even ping works.
Now, as I said I've done it this way many times before...in fact I'm following my documentation from the last successful implementation and even adding in Cisco docs.
Commands take approximately 8 seconds to process when required to authorize with ACS. The show run command will take 8 seconds to process then output is displayed.Packet sniff indicates that it takes 8 seconds for the router to send the initial TCP SYN SEQ packet to ACS. Login to device has no delay.
I have a WS-CE520-8PC Switch. I have tried a full 30/30/30 reset, factory reset, and I am still unable to access the express setup page. Running Win7 x64 on the host os (have tried windows 2000 and xp)It also wont allow me to access direct managment mode when pressing the admin button for 10 sec.
I have a fresh SR520 that I only did two things to it using CCA 3.2(1):
1. Assign the address of FA4 to be 1.23.456.90 with a mask of 255.255.255.252 2. Declared a static nat of 1.23.456.90 port 80 to 192.168.75.12 port 80
I connected laptops to two ports:
1. FA0 (DHCP assigned laptop the address 192.168.75.12) 2. FA4 with the address on the laptop set to 1.23.456.90 and mask of 255.255.255.252
This is an exercise to simulate a cable internet configuration I will install the SR520 into.I can ping and point my browser to 1.23.456.89 and access the web server running there on port 80 via the inside laptop.I CANNOT point my browser to 1.23.456.90 from the outside laptop and make a connection.
What I am doing wrong with NAT? (I believe the problem lies therein as I did even try telling CCA to delete the firewall and I still could not connect to the inside web server).I have a network monitor (Wireshark) on the inside and see nothing coming across. I THINK I see successful NAT translations in the NAT logging (also in the attachment).
I am slowly working my way though the setup and configuration of our new 4900m switch. The switch will have a pretty basic operational configuration. We are simply going to network 3 servers together through the swtich. Anyhow, I have been fallowing the guide at this site: [URL]
Basically the switch is brand new and I just setup things such as the clock, the banner, and the hostname. Anyhow, at various points in the guide such as the configuration of the telnet password and especially the interface gigabitethernet I get the "invalid input detected at '^' marker". I also did a show interfaces and noticed there was not any gigabitethernet interfaces but there was a
"FastEthernet1 is down, line protocol is down Hardware is Fast Ethernet for out of band management, address i"
Anyhow, my thinking is continuing on with the guide and at least try to setup the interface for the management port so I can then use the cisco network assistant gui to then configure the rest of the switch.
I am having an annoying issue the past few weeks. Every time I start my computer, it can't seem to connect to the internet. It says there are no networks available. I then have to restart my computer and everything is all good. How come it is not picking up the internet on the first try?
I can use my computer just fine right now, but whenever I need to restart it, when it comes back on the internet is no longer detected. I am connected through an ethernet wire directly to the internet, with no intermediate router or network.
After failing to solve the problem on my own, the only way Ive found that has been after to restore the internet connection is using the Windows Restore centre and restoring it to about a month ago; restoring it to only a few days ago does not fix the internet.
However, also when I use the restore function, immediately upon starting my system up again I get an error message saying that the system restore has failed and that nothing was changed. But the internet now works again.
Im not really sure what I should do to check out the problem further, let alone remedy it. I run Windows Vista, 64-bit. I can provide further info if need be.
Sometimes they load after restarting computer but if you close browser and try open it again they wont load most of the time.Steam has also stopped working and freezes at part where its trying to connect to account. Also "internet" symbol and bottom left corner says two different things at same time:
Network Internet Connection
Network No Internet Connection
Problem has gotten worse by day. First one restart would fix problem but now steam won't work and if you get pages to load after closing browser you need to restart computer couple of times before pages are loading again.
I am in a third world country (Thailand) with ADSL service and getting customer support is difficult to say the least.The connection is constantly dropping but the real problem lies in that i can not reconnect unless i restart my computer.
i have access to a network printer and everything was working fine previously until last Monday. Now when issue a print command to the printer, the printout delays until i restart the machine before it comes out. If i issue another print command, i would have to go through the same process again. This is actually slowing my work rate and its really an inconvenience.whenever the issue happens, i ping the printers IP address to see if it is actually working. I also check in a browser to see if the printer is ready and all are positive but the problem still remains. Is there a way around this problem.
After restarting my laptop my wireless card (Intel Centrino Wireless-N 1000) has suddenly stopped working (ThinkPad SL410 with Windows 7 Pro 64-bit). The hardware switch is on, the software / Fn switch is on, drivers are recent, device manager says the device is functioning properly, but there's a red X on the network icon in the system tray and obviously no wireless networks are showing up. I thought the wireless card died, but I booted off a linux live CD and the wireless card works just fine.
