Cisco WAN :: 3825 Stuck In Initial Configuration Dialog?
Nov 27, 2012I have configured the box and done the usual wr, copy run start, and the box keeps coming up with the initial config dialog?
View 4 Replies
ADVERTISEMENT
Cisco Firewall :: Stuck At Initial Stage PIX 515e
Oct 30, 2011I have a new pix 515e for Home practice.
1. I couldn't telnet the switch after configuring. should i have to use cross cable or not to connect PC-PIX? (as new switches and routers run through straight cable). more importantly i couldn't even ping the inside ip which is telnet and ssh enabled.
2. Receiving the following after executing each and every command on global mode.
-Configuration Replication is NOT performed From standby Unit to Active Unit
-Configurations are no longer synchronized.
Cisco Switching/Routing :: Stuck At Initial Stage Pix 515e
Oct 30, 2011Stuck at Initial stage CISCO pix 515e
View 2 Replies View RelatedCisco Switching/Routing :: 891 Initial Configuration?
Jan 9, 2013On a recommendation from a network engineer, I got a used Cisco 891. Having worked with small business routers most of my working life, I thought this should not be a problem. However, I had no clue these things used a console and command line to initialize. I have the console cable, am able to console into the device, but am haphazardly issuing command lines straight out of the PDF manual but cannot get Cisco CP to discover the device.
From what I can tell, I am stuck at the point where the manual tells me to enable http server. I ran the command lines several times, executed write mem where available, but when I run the show services command, http is not enabled.
And if you do refere to command lines, I was reading some other forums and they were speaking of "run this command, run that command" but I could not make out the correct syntax, in what mode, whether it be config or config t, etc. So I might need a wee bit of handholding.
I'm hoping that once I can get Cisco CP or CPE to discover the device, I can make my way through the GUI to configure since those usually do make sense to me. As of now, I'm in the thick of it ...
Cisco Wireless :: Initial Configuration On WLC 2504 And AP 1142n?
Mar 3, 2013I will now install a Cisco WLC 2504 and 18 AP´s ( 1142n).
Client has a Cisco infrastruture with Cisco Switch´s 3750x and others.
We expected to have :
1. Managment Vlan to add WLC 2504 and the AP´s ( DHCP server should be reached on this Vlan)
2. Configure a trunk in the switch port where the WLC will connect, allowing vlan´s that we choose to reach.
3. configure WLC ( ssid´s, Vlan´s, interfaces).
4. Configure AP´s.
Is there any basic setup that i missed for things to run ?
Normally I create DHCP reservations for AP`S and for Clients in diferent Vlan´s:
Mgmt Vlan 100: 192.168.0.xx
AP´s vlan 101: 192.168.1.xx
Clients Vlan 102: 192.168.2.xx
All this ones should be created as interfaces on WLC?
Cisco Switching/Routing :: Initial ASA 5510 Configuration
Mar 27, 2012I'm trying to set up a new ASA 5510. I have a pretty simple set up with one /24 on the inside NATed to a DHCP address on the outside. Everything on the inside works and I can ping the outside interface from external devices. No matter what I do I can't get anything internal to route across the border to the outside and back. To try and eliminate ACL issues as a possibility I added permit any any rules to the incoming access lists on the inside and outside interfaces. Here's the sh run.
: Saved
:
ASA Version 8.4(3)
!
hostname gateway
domain-name xxx.local
[code]....
Cisco Switching/Routing :: ASA 5505 Initial Switch Configuration
Jun 24, 2012I am interested in learning and setting up VPN IPSec with Cisco ASA 5505. I've managed to successfully setup VPN andcan connect to it from outside and browse securely to the outside/internet via tunnel. However, once I am connected to VPN, I cannot access any of my internal hosts/servers via VPN client. I am wondering it its a missing ACL/NAT...ASA Version 8.2(5)
!
hostname ciscoasa
enable password xxxxxxxxxxx encrypted
passwd xxxxxxxxx encrypted
names
[code]....
Initial Linksys Wrt54gs Configuration Not Connecting To Internet
May 26, 2011Trying to get this linksys router working on my network. It is a wrt54gs. The machine that i'm configuring it with is running a 64-bit version of windows 7. I run the disc and it seems as if no matter what i try it will not connect to the internet. Can plug modem directly to pc and connect no problem. Can connect to router no problem. But cannot connect to the internet through the router.I made sure that ip addresses are assigned dynamically through dhcp and cloned the mac address of the pc i'm using to do the initial setup.
View 4 Replies View RelatedCisco Firewall :: ASA5520 Unit Not Accessible On Network For Initial Configuration
Dec 15, 2011We received an ASA5520-K8 through Cisco's Loan program so we could demo it as a replacement for our aging Cisco 3005 VPN appliances. Given that we are a non Cisco shop (except for specific appliances like concentrators and wireless access points), I don't have a great deal of experience with Cisco gear.I started to set to setup the appliance this morning but immediately ran into issues. The 5520 doesnt seem to be acting as a DHCP server, and worse yet, I can't access the unit even if I hard code the IP on the PC being used for configuration. I have to say that I feel kinda stupid having to post this, since I actually followed the documentation avaiable for this menial task and I fully expect the problem to be a simple one. Namely, I am using two specific sources of info for connections.
View 20 Replies View RelatedCisco Switching/Routing :: Perform Initial Configuration Of 4900m Switch?
Jan 2, 2013I am slowly working my way though the setup and configuration of our new 4900m switch. The switch will have a pretty basic operational configuration. We are simply going to network 3 servers together through the swtich. Anyhow, I have been fallowing the guide at this site: [URL]
Basically the switch is brand new and I just setup things such as the clock, the banner, and the hostname. Anyhow, at various points in the guide such as the configuration of the telnet password and especially the interface gigabitethernet I get the "invalid input detected at '^' marker". I also did a show interfaces and noticed there was not any gigabitethernet interfaces but there was a
"FastEthernet1 is down, line protocol is down Hardware is Fast Ethernet for out of band management, address i"
Anyhow, my thinking is continuing on with the guide and at least try to setup the interface for the management port so I can then use the cisco network assistant gui to then configure the rest of the switch.
Cisco Firewall :: ASA5510 / 1800 / 3825 - Routing Configuration
Aug 15, 2011I try to setup a ASA5510, but without success. Actually, I have Cisco1800(192.168.96.1/21) from my ISP connected to a Cisco 3825 (via port with IP 192.168.96.2) all is working good. Now I want to insert a asa firewall between ISP router and 3825.
For that, I tried a more simple config :
ISProuter (192.168.96.1/21) ---- ASA outside port(192.168.96.2/255.255.255.248) ASA INSIDE port (192.168.100.1/255.255.255.0) --- a pc with IP 192.168.100.2, netsmask 255.255.255.0, gateway 192.168.100.1
From my ASA, I can ping 192.168.96.1. but a "ping INSIDE 192.168.96.1" fail
from py pc, can ping 192.168.100.1, but not 192.168.96.1
Here, my ASA config :
ASA Version 7.0(8)host name cisco asa
enable password 8Ry2YjIyt7RRXU24 encrypted
password 2KFQnbNIdI.2KYOU encrypted
names dns-guard
!
interface Ethernet0/0
shutdown
no nameif
no security-level
no ip address
[code]....
Cisco Infrastructure :: 2620 - Configuration Register Stuck At 0x3922
Sep 29, 2002I X modem an IOS file to my 2620 router and in the process set the console bps to 115200 which changed the register to 0x3922. Now when I try to connect from the console with any bps, I get garbage!
I can connect from the AUX port and get to the User Exec. mode but since no privileged password is set, I can't get any further to change the config register back to 0x2102.
Wireless :: Toshiba Satellite - Unable To Connect Dialog Box
Feb 15, 2011My Toshiba Satellite (C655-S5049) with Atheros wireless works just fine at my home and a number of public wireless locations (Panara Bread, libraries, school, etc.) There are many other public wireless locations where I try to connect and just get an "unable to connect" dialog box which gives me the options to "diagnose connection problem" (blames the access point). The places that work, work consistently. The places that don't work, I've never been able to get in even though people around me are online with their machines.I'm running thie machine pretty much as it was delivered out of the box. I've installed AVG for virus protection, and I have all the default protection settings (firewall, sharing, etc.).
View 3 Replies View RelatedDell :: KM632 Backspace Opens Save As Dialog
May 6, 2013I have a KM632 wireless keyboard and everytime I hit the backspace button in outlook or any Microsoft Office application it opens a Save As Dialog. How can I correct this?
View 1 Replies View RelatedCisco :: 2620xm Initial Setup Console
May 7, 2012I can start a console connection with my 2620xm, but the only output I get from the terminal software (Putty and Tera Term) is the character " ÿ " at all times even through bootup. For every boot up, I get an additional " ÿ ".I have Baud 9600, 8 bit, no parity, stop 2 bits, no flow.Is there something I am missing?
View 10 Replies View RelatedCisco Firewall :: Initial ASA 5505 Setup?
Aug 4, 2011I have a new Cisco ASA 5505 which I am trying to just setup so that all computers on the LAN can get to the internet (browsing and ping). My current setup attached.
View 1 Replies View RelatedPC Not Connecting On Initial Boot But On Restart It Does
Jan 15, 2013My PC doesn't connect to internet on initial boot, says there is a disconnected cable. On a restart it finds the wirelss card and connects no problem to our BT hub. Tried disabling the wired option, tried a number of things around repairing links etc. but nothing works. it is annoying. PC spec below. Windows 7 is the OS
Giga byte mother board GA-Z68P-DS3
4x4gb of RAM
Intel i5 3.2 CPU
Radeon HD 6770 Graphics card
A wireless adapter TL-WN350GD
A 120 GB SSD hard drive
And a 1TB hard drive
A CnM card reader
Optical DVD drive too
Cisco :: Dial Digits For IVR After Initial Call Completion Through SIP?
Jan 23, 2013I have a 2811 with CME 8.5; I recently added a SIP trunk and can make & receive calls just fine. I noticed today that when connecting to an external IVR system, I can't send additional tones (press 1 for Sales, for example). I have two DIDs, same provider, both doing the same thing. The config for one of my SIP trunk dial peer and translations are shown here - I think this is what's appropriate to review but can add anything else that's necessary. I've also omitted some dial peers for X11 and international dialing for brevity.
View 2 Replies View RelatedCisco Switching/Routing :: 891W ISR - Can't Do Initial Setup?
Nov 6, 2011I'm new to using Cisco Config Professional Express but a lot of things are just "off" with this utility. But my problem for this post is specifically the 891W's internal access point, or initial access to it.
My situation is that I have some 891W's. It's my first time working with them, as well as with CCP Express (2.5). After isolating the router and my PC to their own network, using the IP my PC got via DHCP frmo the router I opened a web broswer and connected to the router. The initiial configuration wizard came up and I went through the various screens. One of those screens had basic config info for the internal wireless AP which I provided. Somewhere in that screen it asked for a Hostname for the AP, and a password. It doesn't askfor a username though. To ensure I wouldn't run into confision, I made sure to set every password I ever get asked to configure as the same thing so the AP's password was also the same.
However after I finish with the wizard, the java-based CCP Express begins prompting me for first the main router credentials which I provide and it gets the router config, then it prompts mefor the username/password for the Access Point. First of all, the initial config wizard had never asked me for the username for the access point, only the hostname, and the password. I had assumed it was just going to use the main router username, or perhaps a blank username.
In any case, nothing I type ever works. I've used cisco/cisco, or a blank username with my new password, or the same username as the main router with the password ---- nothing. This is now the 4th time I have completely Reset the router to factory defaults and while I am learning the use of CCP Express through repetition, I'd also like to get this thing configured and out the door so my customer can use it.
Cisco Firewall :: Initial Connections To SQL Servers Timeout Through ASA 8.2(1)
Aug 23, 2012I am on version 8.2(1) of ASA Code.When accessing a SQL server on a secure internal interface,(Traffic is sourcing from DMZ) i'm getting some timeouts on the initial connection on port 1433. All subsequent connections work fine. Packet tracer shows the connection builds properly, and shouldn't have a connectivity issue. The problem server is a webserver that connects back through the firewall to access the SQL server on port 1433. We also have many other webservers in the DMZ which access the same SQL server, but do not have the same timeout issues. Here are my timeouts, from the config
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
arp timeout 14400
I've seen a couple articles about increasing the tcp timeout to 3 hours for the DMZ interface?
Cisco :: 851W Initial Setup / SDM Wizard Fails
Jun 21, 2011I bought a Cisco 851W router from a coworker about a year ago and tried setting it up at my home with nothing but headaches. I finally gave up and went with DD-WRT and have yet to look back (my $40 router outperforms this thing on so many levels, but I'm getting off-topic!). I recently re-discovered this beast and pulled it out of storage to see if I could get a test network setup at home to practice on. I checked for any IOS updates and downloaded (and installed) the lastest image (c850-advsecurityk9-mz.124-15.T15.bin). I consoled in and verified the initial 10.10.10.1 IP was configured in the VLAN1 interface and directly connected a PC to one of the switchports and pulled a 10.10.10.2 address. I pull up SDM from my browser (I have used FF, IE, and Chrome, all with the same results. Java version is the latest, 6 Update 26.) and it launches the initial configuration wizard. I go through the steps and get up to the DHCP Configuration (after LAN, before Internet/WAN setup) and try to click Next and nothing happens. It doesn't freeze as I can easily go Back, but can never move forward beyond the DHCP configuration. Pressing Cancel on the wizard just shuts down SDM as a whole and exits.
In my troubleshooting steps, I did notice that as soon as I click Next in the DHCP configuration, nothing will happen in the wizard, but the SDM window in the background will automatically present the "Apply Changes" and "Discard Changes" buttons, which weren't there in the previous steps. Of course, neither of those are clickable due to the wizard being open. I really don't want to configure this thing from scratch using the CLI if I don't have to..is there ANY way I can bypass the SDM Wizard at all? Also, I'm running SDM Express, would downloading ASDM and trying to connect from there make any difference?
Cisco Wireless :: Initial Setup Loop On 5508
Apr 5, 2013I have a new from the box 5508 which I am attempting to follow the initial setup process to IP it. When I make it through the initial setup the box reboots buts brings me back to the "terminate auto-install" prompt again for some weird reason?
View 2 Replies View RelatedIP Address Randomly Dropping At Initial Start Up?
Feb 26, 2012Recently I am having a problem during the initial start up. I am running Windows 7. After the computer starts up, I do not have an internet connection. The yellow triangle with an exclamation mark in it appears in the bottom right on the monitors. I can go to the internet connections and disable, then enable and my connection returns. This is only happening during the initial start up. This happens 3 out of 4 times during start up. I have had the cable company check everything and they are saying it is an issue with my computer.
View 1 Replies View RelatedCisco Switching/Routing :: Router 1811 Initial Startup
Feb 25, 2013I have manual Cisco 1812 (1811) Integrated Srvice Router Cabling and Installation in front of meI have Cisco 1811 connected to my laptop according to this manualI have Cisco SDM latest version installed on my laptopI have DHCP enabled on my laptopThe problem that my laptop can't get valid IP adreess from the router (see att. laptop_, laptop_2)
Which IP address I have to use in order to get access to router inrerface (see. SDM_1)?
Cisco Wireless :: 6500 - Unable To Connect Via GUI After Initial WISM2 Setup
Feb 7, 2013I've installed our previous WISMs and other WISM2s previously and never had a problem.
6500 running SXJ2. WISM2 running 7.3.101.0 (which is what the rest of our WISM2s are on)
Insert WISM and go through initial setup. Run a show wism status on the 6500, and show sysinfo on the WISM. All looks good. Service port and management vlans are up. From the 6500 I can ping the service port IP, but not the management IP. From the WISM I can't ping the managment default gw but I can the service port. Unable to get anything back from the GUI..not surprising as not even ping works.
Now, as I said I've done it this way many times before...in fact I'm following my documentation from the last successful implementation and even adding in Cisco docs.
Cisco AAA/Identity/Nac :: 3841 Authorization Commands Take 8 Seconds To Send Initial TCP
Aug 24, 2012Device: 3841
IOS: 15.1(4)M2 ADVSecurity
Commands: AAA Authorization
Commands take approximately 8 seconds to process when required to authorize with ACS. The show run command will take 8 seconds to process then output is displayed.Packet sniff indicates that it takes 8 seconds for the router to send the initial TCP SYN SEQ packet to ACS. Login to device has no delay.
Cisco Switching/Routing :: CE520-8PC Switch - Port Won't Allow Initial Config
Mar 9, 2013I have a WS-CE520-8PC Switch. I have tried a full 30/30/30 reset, factory reset, and I am still unable to access the express setup page. Running Win7 x64 on the host os (have tried windows 2000 and xp)It also wont allow me to access direct managment mode when pressing the admin button for 10 sec.
View 2 Replies View RelatedCisco Switching/Routing :: SR520-FE-K9 Initial Setup Blocks HTTP
Sep 4, 2012I have a fresh SR520 that I only did two things to it using CCA 3.2(1):
1. Assign the address of FA4 to be 1.23.456.90 with a mask of 255.255.255.252
2. Declared a static nat of 1.23.456.90 port 80 to 192.168.75.12 port 80
I connected laptops to two ports:
1. FA0 (DHCP assigned laptop the address 192.168.75.12)
2. FA4 with the address on the laptop set to 1.23.456.90 and mask of 255.255.255.252
This is an exercise to simulate a cable internet configuration I will install the SR520 into.I can ping and point my browser to 1.23.456.89 and access the web server running there on port 80 via the inside laptop.I CANNOT point my browser to 1.23.456.90 from the outside laptop and make a connection.
What I am doing wrong with NAT? (I believe the problem lies therein as I did even try telling CCA to delete the firewall and I still could not connect to the inside web server).I have a network monitor (Wireshark) on the inside and see nothing coming across. I THINK I see successful NAT translations in the NAT logging (also in the attachment).
Cisco 3825 Killing The CPU
Mar 6, 2012The process is IP Input and I'm not really sure how to troubleshoot it. I've read through all the doc's on high cpu load if I shutdown the port that feeds that network, CPU drops to around 30%, bring it back up and it jumps up to 90%+. I've got a policy map on the interface shaping the traffic
[code]...
Cisco WAN :: 3825 Upgrade To 12.4(24).t6?
Sep 19, 2011I am trying to upgrade the IOS on cisco 3825 from 124-9.T1.bin to 124.24.t6.bin, after I upload the configuration to the CF and verify the file, everything appears fine but when I try to load the new image it fails with following error and falls back to old image :-
System Bootstrap, version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
Readonly ROMMON intializedboot: cannot open "flash:"
an alternate boot helper program is not specified
(monitor variable "BOOTLDR" is not set)
and unable to determine first file in bootflash
loadprog: error - on file open
boot: cannot load "c3825-advsecurityk9-mz.124-24.T6.bin"
Then after few minutes it boot to the Old 12(4).9 ios again.
Cisco WAN :: Upgrading 3825 ISR From 12.4 To 15?
Apr 10, 2011What are the prerequisites before doing this? I have to upgrade a router this Wednesday evening if there is an opportunity to move it to a code that is more current that the one the client is currently running which is 12.4(25b). I see on the Cisco Support site that after this code, everything moves to 15.
View 5 Replies View RelatedCisco :: Rate Limiting On 3825?
Feb 24, 2011I have a 3825 with a 16 port etherswitch card installed that I'm trying to setup rate-limits on. Interface G0/0 is the connection to the outside world and int g0/1 has a couple of 2950 switches attached to it.
The etherswitch card, f1/0, f1,1 etc has corresponding vlans, 902, 903 etc each with an IP 10.110.1.x, 10.110.2.x and all part of access-group 111. The switches connect on sub-interfaces g0/1.101, g0/1.102 etc and have IP's 10.55.1.x, 10.55.2.x and part of access-group 101.
What i'm trying to achieve is that every port / IP that is on access-group 111 shares 3Mb of bandwidth in/out and access-group 101 shares a separate 3Mb of bandwidth in/out.
I've created two access-lists as follows;
access-list 101 permit ip 10.55.0.0 0.0.255.255 any
access-list 111 permit ip 10.110.0.0 0.0.255.255 any
And on int g0/0 I've created the following rate-limits;
rate-limit input access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit input access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 101 3072000 64000 64000 conform-action transmit exceed-action drop
rate-limit output access-group 111 3072000 64000 64000 conform-action transmit exceed-action drop
Now instead of both access-groups having 3Mb each they all seem to be sharing 3Mb! I've tried class-maps and policy-maps but to no avail..
Cisco EPC-3825 / WAN Conflicts With LAN Subnet?
Nov 11, 2011LAN subnet conflicts with WAN subnet. My router is d-link 825 and my cable modem is Cisco EPC-3825. Op system is W7. Everything worked great with an older cable modem (Cisco 3000).
View 4 Replies View Related