Cisco Wireless :: 6500 - Unable To Connect Via GUI After Initial WISM2 Setup
Feb 7, 2013
I've installed our previous WISMs and other WISM2s previously and never had a problem.
6500 running SXJ2. WISM2 running 7.3.101.0 (which is what the rest of our WISM2s are on)
Insert WISM and go through initial setup. Run a show wism status on the 6500, and show sysinfo on the WISM. All looks good. Service port and management vlans are up. From the 6500 I can ping the service port IP, but not the management IP. From the WISM I can't ping the managment default gw but I can the service port. Unable to get anything back from the GUI..not surprising as not even ping works.
Now, as I said I've done it this way many times before...in fact I'm following my documentation from the last successful implementation and even adding in Cisco docs.
View 7 Replies
ADVERTISEMENT
Mar 28, 2012
I've just reset our WISM2 in the test lab back to factory default as I needed to reconfigure the 6500 and the WISM2 itself. Bearing in mind I had it working before.I've just renamed and re-addressed some of the vlans so things flow better and make it easier to add more WISM2s in the future.Now I've run through the initial configuration and it's rebooted ok and show WISM status is showing Oper-Up and there's a port channel 407 been created as I would expect. However, I am unable to get to the management interface via GUI or SSH. In fact from the 6500 I can't even ping the management interface (but I can the service port).The Vlans have been changed in the 6500 config so it knows the native-vlan and service vlan etc and all the vlans are up/up.
View 17 Replies
View Related
Jun 27, 2012
I have a situation where a customer doesn't have the required power units installed in their 6500 for me to provision a WiSM2.They use a VSS pair with a single Sup720 in each. They have no intention of adding a second Sup to each chassis.
I need to justify why they can't use slot 6 (which has power reserved) if I am to get them to upgrade the PSU's. The documentation I've found says it is supported but not recommended.
View 1 Replies
View Related
Jul 21, 2012
how to safely remove the WiSM2 from the Catalyst 6500 series switch? According to the documentation "Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note":
To remove the WiSM2, perform these steps:
Step1 Shut down the module by one of these methods: In privileged mode from the router prompt, enter the hw-mod module mod shutdown command. NoteIf you enter this command to shut down the module, you must enter the following commands in global configuration mode to restart (power down, and then power up) the module: Router# no power enable module modRouter# power enable module mod If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.
Step2 Verify that the WiSM2 shuts down. Do not remove the module from the switch until the POWER LEDis off.
But, in the case of Step1 (1st methods) I do not see a option "shutdown" in the command "hw-mod module 3"...
All I prompted to enter is: c6500#hw-module module 3 ?
boot Specify boot options for the module through Power Management Bus control register
reset Reset specified component
simulate Simulate options for the module Is it hidden options?
IOS version of c6500 is 12.2(33)SXJ1
In the case of Step2 (2nd methods) there is not any button on the front panel of the module?
And yet, it is better to remove the module configuration manually or use the command module clear-config prior to removing the module?
View 14 Replies
View Related
Apr 5, 2013
I have a new from the box 5508 which I am attempting to follow the initial setup process to IP it. When I make it through the initial setup the box reboots buts brings me back to the "terminate auto-install" prompt again for some weird reason?
View 2 Replies
View Related
May 7, 2012
I can start a console connection with my 2620xm, but the only output I get from the terminal software (Putty and Tera Term) is the character " ÿ " at all times even through bootup. For every boot up, I get an additional " ÿ ".I have Baud 9600, 8 bit, no parity, stop 2 bits, no flow.Is there something I am missing?
View 10 Replies
View Related
Aug 4, 2011
I have a new Cisco ASA 5505 which I am trying to just setup so that all computers on the LAN can get to the internet (browsing and ping). My current setup attached.
View 1 Replies
View Related
Nov 6, 2011
I'm new to using Cisco Config Professional Express but a lot of things are just "off" with this utility. But my problem for this post is specifically the 891W's internal access point, or initial access to it.
My situation is that I have some 891W's. It's my first time working with them, as well as with CCP Express (2.5). After isolating the router and my PC to their own network, using the IP my PC got via DHCP frmo the router I opened a web broswer and connected to the router. The initiial configuration wizard came up and I went through the various screens. One of those screens had basic config info for the internal wireless AP which I provided. Somewhere in that screen it asked for a Hostname for the AP, and a password. It doesn't askfor a username though. To ensure I wouldn't run into confision, I made sure to set every password I ever get asked to configure as the same thing so the AP's password was also the same.
However after I finish with the wizard, the java-based CCP Express begins prompting me for first the main router credentials which I provide and it gets the router config, then it prompts mefor the username/password for the Access Point. First of all, the initial config wizard had never asked me for the username for the access point, only the hostname, and the password. I had assumed it was just going to use the main router username, or perhaps a blank username.
In any case, nothing I type ever works. I've used cisco/cisco, or a blank username with my new password, or the same username as the main router with the password ---- nothing. This is now the 4th time I have completely Reset the router to factory defaults and while I am learning the use of CCP Express through repetition, I'd also like to get this thing configured and out the door so my customer can use it.
View 3 Replies
View Related
Jun 21, 2011
I bought a Cisco 851W router from a coworker about a year ago and tried setting it up at my home with nothing but headaches. I finally gave up and went with DD-WRT and have yet to look back (my $40 router outperforms this thing on so many levels, but I'm getting off-topic!). I recently re-discovered this beast and pulled it out of storage to see if I could get a test network setup at home to practice on. I checked for any IOS updates and downloaded (and installed) the lastest image (c850-advsecurityk9-mz.124-15.T15.bin). I consoled in and verified the initial 10.10.10.1 IP was configured in the VLAN1 interface and directly connected a PC to one of the switchports and pulled a 10.10.10.2 address. I pull up SDM from my browser (I have used FF, IE, and Chrome, all with the same results. Java version is the latest, 6 Update 26.) and it launches the initial configuration wizard. I go through the steps and get up to the DHCP Configuration (after LAN, before Internet/WAN setup) and try to click Next and nothing happens. It doesn't freeze as I can easily go Back, but can never move forward beyond the DHCP configuration. Pressing Cancel on the wizard just shuts down SDM as a whole and exits.
In my troubleshooting steps, I did notice that as soon as I click Next in the DHCP configuration, nothing will happen in the wizard, but the SDM window in the background will automatically present the "Apply Changes" and "Discard Changes" buttons, which weren't there in the previous steps. Of course, neither of those are clickable due to the wizard being open. I really don't want to configure this thing from scratch using the CLI if I don't have to..is there ANY way I can bypass the SDM Wizard at all? Also, I'm running SDM Express, would downloading ASDM and trying to connect from there make any difference?
View 1 Replies
View Related
Sep 4, 2012
I have a fresh SR520 that I only did two things to it using CCA 3.2(1):
1. Assign the address of FA4 to be 1.23.456.90 with a mask of 255.255.255.252
2. Declared a static nat of 1.23.456.90 port 80 to 192.168.75.12 port 80
I connected laptops to two ports:
1. FA0 (DHCP assigned laptop the address 192.168.75.12)
2. FA4 with the address on the laptop set to 1.23.456.90 and mask of 255.255.255.252
This is an exercise to simulate a cable internet configuration I will install the SR520 into.I can ping and point my browser to 1.23.456.89 and access the web server running there on port 80 via the inside laptop.I CANNOT point my browser to 1.23.456.90 from the outside laptop and make a connection.
What I am doing wrong with NAT? (I believe the problem lies therein as I did even try telling CCA to delete the firewall and I still could not connect to the inside web server).I have a network monitor (Wireshark) on the inside and see nothing coming across. I THINK I see successful NAT translations in the NAT logging (also in the attachment).
View 2 Replies
View Related
Sep 17, 2012
We have some new WISM2 running 7.0.116.0, but now we need to upgrade their license to suport 1000 APs. So I am looking at upgrading the software to 7.2.110.0. We are running WCS at the moment and got NCS with the new WISM2, so going to 7.3 and buying Prime Infrastructure is not an option at the moment, thus we are going for 7.2.
The thing is I can't seem to find much info about this upgrade. Is 7.0->7.2 a smooth upgrade? Do we need to do any configuration changes to the WISM2 or LAP1242? We are running H-REAP, will the change to FlexConnect be affected? I can't seem to find anything regarding requirements for 6500/SUP for running WISM2 7.2, do I need a certain software for that?
View 5 Replies
View Related
Mar 13, 2013
I have a question regarding WISM2 DP and licensing.
Suppose i have a WISM2 with 7.0, 500AP license today and i activate WISM2-DP by upgrading to 7.2,Do i get 500 AP capacity for free (total 1000AP) or do i get 250APs on each WISM2-blade ?
If i get 500APs for free, why is Cisco selling an expensive licensed 1000 AP WISM2 ? I better buy a single-plane 500AP-WISM2 and upgrade it myself then...50% profit.
Is this the same for a WISM2-300 (supporting 300 APs) ?When i activate WISM2-DP here, do i get an extra 300 AP or an extra 500 APs ? Or 150AP on each blade ?
View 7 Replies
View Related
Dec 19, 2012
I having an issue with WCS and the new code 7.4 on my WiSM2 blade. When I try to refresh configuration from/to controller it fails. I just upgraded from 7.01 and it worked before the upgrade.
Is this not supported?
I am able to change configuration from WCS to the WiSM2 and it works fine just cant copy config.
View 7 Replies
View Related
Jan 18, 2013
I have just been setting up a WISM2 in a test lab and for some reason the Supervisor is not creating a port channel on my 6500 as suggested in the WISM2 Deployment Guide. WISM2 is installed in an appropriate slot (according to same doco) and have attempted reset to factory defaults, removing and power cycling several times.
View 1 Replies
View Related
Jan 8, 2013
I have installed WiSM2 with ver 7.4 and Bonjour works great with instruction provided, But…… 2 problems. I cant get it to work on the same subnet. (odd since the whole problem was not able to work across subnets), More important the new Code function / password function on the airplay wont work. I get the code on the projector, but the ipad never pop up the login box it just errors out.
View 2 Replies
View Related
Dec 12, 2012
I am about to migrate WISM1 to WISM2, The image of WISM1 is 6.0.199.4 and the image of WISM2 is 7.2.111.3.
Do i need to upgrade WISM1 to 7.2.111.3 before i export the configuration and import it into WISM2? Or can i just export the configuration from WISM1 on 6.0.199.4 and import directly to WISM2 which is on 7.1.111.3?
View 2 Replies
View Related
Apr 5, 2012
My company has been contracted to upgrade the 2 WiSM1 modules on a 6509 for a customer. The hardware isn't changing but the software is being upgraded to WiSM2. The cutsomer has HUNDREDS of AP's and dozens of VLANs and subnets (large municipality and school district).
Cisco SE's have been pushing the customer to purchase the WCS 7 software (they've been managing these Controllers independantly) stating there is no mechanism to upgrade WiSM1 configs to WiSM2. I am vaguely familiar with the cisco controllers but have little WiSM experience. So i feel like i'm working without a net here.
So,
1) Any way to migrate from 1 to 2 without the WCS and without having to reinvent the wheel?
2) How does the WCS make this transition easier? What does it do to the WiSM1 configs to make them WiSM2 compatable?
View 21 Replies
View Related
Apr 10, 2013
I have a wireless network running with Controller WISM2 and I also have a NCS.I want to know if there is any way to look of individual log of CAPWAP and LAPWAP Access Points. It is better if I can see it through NCS.
View 1 Replies
View Related
Dec 16, 2012
it is normal for the WISM2 time to be resetted to default of 1 Jan 2000 after rebooting the 6506E if no NTP is configured?I had to configure it back to the correct time. If not, the APs will not come up.Also, does the ap or wlc keep track of the ap group the ap is provisioned to?
View 3 Replies
View Related
Mar 3, 2013
I will now install a Cisco WLC 2504 and 18 AP´s ( 1142n).
Client has a Cisco infrastruture with Cisco Switch´s 3750x and others.
We expected to have :
1. Managment Vlan to add WLC 2504 and the AP´s ( DHCP server should be reached on this Vlan)
2. Configure a trunk in the switch port where the WLC will connect, allowing vlan´s that we choose to reach.
3. configure WLC ( ssid´s, Vlan´s, interfaces).
4. Configure AP´s.
Is there any basic setup that i missed for things to run ?
Normally I create DHCP reservations for AP`S and for Clients in diferent Vlan´s:
Mgmt Vlan 100: 192.168.0.xx
AP´s vlan 101: 192.168.1.xx
Clients Vlan 102: 192.168.2.xx
All this ones should be created as interfaces on WLC?
View 11 Replies
View Related
Jan 3, 2013
We are thinking of introducing ASA's into our setup instead of using FWSM for our firewalls with our 6500. Currently we use multiple contexts with the FWSM, as we provide hosting services for multiple clients and want them behidn their own firewall. My question is how can we make this happen with an ASA. Since with the FWSM we use the backplane of the 6500 and SVI's for all interfaces between them. For example if we have 20 clients what will be the ideal setup for us to use with an ASA. If we can infact use mutiple contexts how can we? Is there a way we can maybe bundle all the ports in the ASA into the 6500 as a layer two trunk port and continue to use SVIs to manage all the clients.
View 3 Replies
View Related
Dec 5, 2011
We have an issue with our 6500 catalysts.
We are regularly seeing the error above on our cat6500 devices when executing a 'sh run ' command:
We've seen this error for quite some time but the frequency seems to be increasing up to the point where it becomes problematic now because backups and other automated actions are failing regularly.
We don't see multiple processes with the commando "sh config lock" at that time. But when we do a "sh users", we can see sometimes multiple users.
I supose it is possible for multiple users to do a logon at the same time, but not make changes at the same time.
We are using IOS s72033-ipservicesk9_wan-mz.122-33.SXI7.bin. It seems that all switches with these IOSses seem to have the problem. But in the bug toolkit I can't find any reference to a bug...
View 3 Replies
View Related
Mar 25, 2011
HP Officejet 6000 wire ethernet set up always fails at end of set-up script. HP forum was useless. PC is running Win XP, router is Netgear WGR 614. Router shows printer as attached device. Printer connects OK with USB
View 2 Replies
View Related
Jul 23, 2012
I've already done plenty of web search and gone through various forums. That's how I've gained knowledge of setting up wireless bridge. But for some unknown reasons I haven't been able to successfully pull it off. Let me explain.I have an ISP provided modem+wifi device. Its called PTCL Modem. I normally connect my laptop and other devices through its wifi. I need to extend the signals around my workplace. So I have bought a TP-Link wifi router (TL-WR740N). Both these devices support wireless bridging according to their admin settings. I'll go pic-by-pic to explain what steps I performed.Pic1: PTCL Modem wireless bridging options. It shows two options for AP Mode: Access Point and Wireless Bridge. And it shows three options for Bridge Restrict.
Pic2: TP-Link router home page Pic2a: I first change the TP-Link's IP Address, because the PTCL Modem's wireless is also using the same IP address (192.168.1.1) so the current address will conflict with it. I change the router's IP address to 192.168.2.1. It goes for a restart.Pic3: Next I turn off the DHCP Server, as suggested by various blogs and forums. Router goes for another reboot after saving this setting.Pic4: Now I go to Wireless Settings page and set Enable WDS on. It shows me bridging options.Pic5.
I click the Survey button and it shows me a list of wireless devices in its range along with their BSSID and Channel number. I select my PTCL Modem access point which is on Channel 6. My PTCL Modem's wireless is set to WPA2-PSK security with the password "********". I also set the Channel on my TP-Link router from Auto to 6, to come in line with PTCL Modem's wireless. Clicking Save makes router goes for another reboot.
View 8 Replies
View Related
Jan 22, 2012
I have a pair of 6500's setup with VSS and there is currently only one link between then. However one end of the link is on Po10 and the other end is on Po25. If I move the Po25 over to Po10, will things break? It seems to be working fine now. I'm about to add a second link and I'm concerned about the current configuration. It makes more sense to me to have both ends of the same link on the same port-channel ID. I've seen documentation which states otherwise however.
interface Port-channel10
no switchport
no ip address
[Code]....
View 2 Replies
View Related
Feb 29, 2012
I have been having an annoying issue for the past few weeks with my ASA setup. We are using the ASA as our Remote Access Gateway and originally had it setup in a Active/Standby failover configuration using 2 x 5520 ASA's.The original setup of the devices was that the 2 x ASA were setup in a failover configuration, with both of them connecting back to the internal network via a 6500 device. Because of using failover I created a VLAN on the 6500 and put the two ports that connect the ASA's into that VLAN. I then configured the VLAN interface to be the EIGRP interface for the neighbour relationship to the ASA's.
The problem I am seeing is that the EIGRP neighbour relationship between the Active ASA and the 6500 keeps flapping. It occurs abour 4-5 times every day at randmon intervals. Sometimes the neighbour relationship will stay up for 6-7 hours, other times it flaps every 1-2 hours. I initially thought it was due to the failover configuration so I removed one of the ASA's and removed all of the failover configuration, but the EIGRP neighbour flapping problem still exisits. [code] Since removing the failvoer configuration I am thinking it could be a physical cable problem?
View 4 Replies
View Related
Mar 27, 2013
We have 6500 chassises in our set up. But using CWLMS 4.0 , we are unable to manage VSS feature of 6500.Also User tracking for Nexus 7K Switches subnets are not working.
View 1 Replies
View Related
Oct 5, 2011
Side Catalyst 6509 : cata6#sho running-config interface gigabitEthernet 8/15 Building configuration...
Current configuration : 224 bytes
!
interface GigabitEthernet8/15
switchport
[Code].....
View 6 Replies
View Related
Nov 5, 2012
What is the reason of following NTP error. I am unable to configure further ntp peers on the router. Could not able to understand the reason of 100 peers. I am adding only 2nd peer on the router but getting this error. There is no problem adding peers in other 6500s .
View 2 Replies
View Related
Aug 23, 2012
I just installed a WAP321. I literally configured a test SSID, implemented WPA Personal security, and could not get an iPad or Blackberry to associate with the network. The error message that appears in the Blackberry is "EAP Authentication Failed". But isn't EAP applicable only to the WPA Enterprise mode? The access point works fine if I have the test SSID without any security, but as soon as I turn on WPA Personal security, nothing can connect. Is there something really obvious I'm missing here?(When I select WPA Personal security, I have tried with just the "WPA2" version and "AES" cipher selected, as well as with check boxes ticked on both WPA/WPA2, and on both TKIP/AES. Neither works.)
View 8 Replies
View Related
Apr 10, 2012
I have 3 desk tops and 1 Laptop. the desk tops are wireless connected via my Xfinity ( cable Modem) and a Trendnet 652- 300 mgb router setup. Recently installed the
Trendnet router ( initially w/o security). I was able to readily connect to and access all pcs to Internet. However, recently went to Trendnet on line site and installed Router password security. Was able to connect and access the Internet on 2 of the 3 desktop pcs as well as the Laptop. However, 1 desktop ( running on Windows XP Professional, 5.1.2600 SVCPK 3, Optiplex G x 60 ) does not permit access to Internet. Once I get to the screen asking for the password ( network key) , I insert same I receive an error message stating "Network key s/b WEP pr a WPA key".
View 4 Replies
View Related
Feb 7, 2012
I have been having wireless issues for a while now and decided to buy a TP-Link router to work with this, unfortunately the wrong model was sent out, it's for Cable use only as it is just a router not modem too!I attempted to send it back but as I didn't know it was wrong until I opened it they won't take it back now as I should have checked first apparently.I did some research online and found information that I can use it as my wireless transmitter as long as I use my SKY router as the modem (with it's wireless function switched off).I have attempted the set-up as described in the manual for the TP-Link and I am now speaking to you using the Ethernet port on it, yet none of my wireless devices can see it in the available networks, both the "system" and "WLAN" lights are flashing to say the router is working but I still have no wireless signal.
View 10 Replies
View Related
Nov 4, 2012
So i got time warner cable and internet but for some odd reason a "wired" connection works perfectly fine but i cannot get any life out of my belkin n750 DB wireless router. ive hooked it all up modem to router to pc nothing so i reset everything still nothing
View 3 Replies
View Related
