I have a new from the box 5508 which I am attempting to follow the initial setup process to IP it. When I make it through the initial setup the box reboots buts brings me back to the "terminate auto-install" prompt again for some weird reason?
View 2 RepliesI've installed our previous WISMs and other WISM2s previously and never had a problem.
6500 running SXJ2. WISM2 running 7.3.101.0 (which is what the rest of our WISM2s are on)
Insert WISM and go through initial setup. Run a show wism status on the 6500, and show sysinfo on the WISM. All looks good. Service port and management vlans are up. From the 6500 I can ping the service port IP, but not the management IP. From the WISM I can't ping the managment default gw but I can the service port. Unable to get anything back from the GUI..not surprising as not even ping works.
Now, as I said I've done it this way many times before...in fact I'm following my documentation from the last successful implementation and even adding in Cisco docs.
I can start a console connection with my 2620xm, but the only output I get from the terminal software (Putty and Tera Term) is the character " ÿ " at all times even through bootup. For every boot up, I get an additional " ÿ ".I have Baud 9600, 8 bit, no parity, stop 2 bits, no flow.Is there something I am missing?
View 10 Replies View RelatedI have a new Cisco ASA 5505 which I am trying to just setup so that all computers on the LAN can get to the internet (browsing and ping). My current setup attached.
View 1 Replies View RelatedI'm new to using Cisco Config Professional Express but a lot of things are just "off" with this utility. But my problem for this post is specifically the 891W's internal access point, or initial access to it.
My situation is that I have some 891W's. It's my first time working with them, as well as with CCP Express (2.5). After isolating the router and my PC to their own network, using the IP my PC got via DHCP frmo the router I opened a web broswer and connected to the router. The initiial configuration wizard came up and I went through the various screens. One of those screens had basic config info for the internal wireless AP which I provided. Somewhere in that screen it asked for a Hostname for the AP, and a password. It doesn't askfor a username though. To ensure I wouldn't run into confision, I made sure to set every password I ever get asked to configure as the same thing so the AP's password was also the same.
However after I finish with the wizard, the java-based CCP Express begins prompting me for first the main router credentials which I provide and it gets the router config, then it prompts mefor the username/password for the Access Point. First of all, the initial config wizard had never asked me for the username for the access point, only the hostname, and the password. I had assumed it was just going to use the main router username, or perhaps a blank username.
In any case, nothing I type ever works. I've used cisco/cisco, or a blank username with my new password, or the same username as the main router with the password ---- nothing. This is now the 4th time I have completely Reset the router to factory defaults and while I am learning the use of CCP Express through repetition, I'd also like to get this thing configured and out the door so my customer can use it.
I bought a Cisco 851W router from a coworker about a year ago and tried setting it up at my home with nothing but headaches. I finally gave up and went with DD-WRT and have yet to look back (my $40 router outperforms this thing on so many levels, but I'm getting off-topic!). I recently re-discovered this beast and pulled it out of storage to see if I could get a test network setup at home to practice on. I checked for any IOS updates and downloaded (and installed) the lastest image (c850-advsecurityk9-mz.124-15.T15.bin). I consoled in and verified the initial 10.10.10.1 IP was configured in the VLAN1 interface and directly connected a PC to one of the switchports and pulled a 10.10.10.2 address. I pull up SDM from my browser (I have used FF, IE, and Chrome, all with the same results. Java version is the latest, 6 Update 26.) and it launches the initial configuration wizard. I go through the steps and get up to the DHCP Configuration (after LAN, before Internet/WAN setup) and try to click Next and nothing happens. It doesn't freeze as I can easily go Back, but can never move forward beyond the DHCP configuration. Pressing Cancel on the wizard just shuts down SDM as a whole and exits.
In my troubleshooting steps, I did notice that as soon as I click Next in the DHCP configuration, nothing will happen in the wizard, but the SDM window in the background will automatically present the "Apply Changes" and "Discard Changes" buttons, which weren't there in the previous steps. Of course, neither of those are clickable due to the wizard being open. I really don't want to configure this thing from scratch using the CLI if I don't have to..is there ANY way I can bypass the SDM Wizard at all? Also, I'm running SDM Express, would downloading ASDM and trying to connect from there make any difference?
I have a fresh SR520 that I only did two things to it using CCA 3.2(1):
1. Assign the address of FA4 to be 1.23.456.90 with a mask of 255.255.255.252
2. Declared a static nat of 1.23.456.90 port 80 to 192.168.75.12 port 80
I connected laptops to two ports:
1. FA0 (DHCP assigned laptop the address 192.168.75.12)
2. FA4 with the address on the laptop set to 1.23.456.90 and mask of 255.255.255.252
This is an exercise to simulate a cable internet configuration I will install the SR520 into.I can ping and point my browser to 1.23.456.89 and access the web server running there on port 80 via the inside laptop.I CANNOT point my browser to 1.23.456.90 from the outside laptop and make a connection.
What I am doing wrong with NAT? (I believe the problem lies therein as I did even try telling CCA to delete the firewall and I still could not connect to the inside web server).I have a network monitor (Wireshark) on the inside and see nothing coming across. I THINK I see successful NAT translations in the NAT logging (also in the attachment).
how to setup the 5508 Series LAN wireless controller. The online documentation are not details. What different between Service Interface IP and Management interface IP. The device IP is using what type service or management interface.
View 2 Replies View RelatedI have a Cisco 5508 setup an running with Cisco 3502 AP. with same SSID
however i need segment the network using 3-Diff VLANS:
1. vlan 1-----students
2. vlan2----- Visitors
3.vlan3------ Staff
the students and visitor are not ment to login to the corporate network, however the staff are to be login using their Active Directory User name and Password how to i achieve this ?
I have finally got my office extend AP to connect to my companies 5508 controller by enabling NAT on the management interface and can see all the cooperate SSID's. However when I try to connect to the SSID my client either gets a local IP address from my home router or then cannot get any IP address.
View 9 Replies View RelatedI've just installed a standard Cisco wireless install (5508, 3502i, local and flexconnect setups) all working swimmingly.
The customer has asked for a new WLAN for a particular group of staff that will route to a different gateway than the general wireless staff.
The 5508 is connected to a older Avaya L3 switch that is the customers core swtich, but it isn't capable of PBR so it routes on desitnation only and its default route is not where I need the new WLAN traffic to route to. An ASA will be connected to the Avaya switch (which is the alternate gateway I need to get the new WLAN users to). So my question is probably routing 101, but if the ASA interface, the Avaya swtich and the WLAN interface all reside in the same VLAN, can I give the wireless clients the ASA as their gateway via DHCP and successfully get their traffic to the ASA?
I have a wlc 5508 and I'd like to setup a network for visitors. They will connect to the WLAN, enter a password and then automatically get redirected to an external website. I understand the wlc 5508 supports this but I'm struggling to find out how to set this up I assume this can be done without having to customise webauth bundles?
View 2 Replies View RelatedLet's say I have 3 APs, all connected to a WLC 5508,Each AP has a computer that is connected to it, Computer A, B and C, all on the same Vlan with same SSID
Is it possible to configure so
A and B can not talk to each other but both can talk to C ?
Something like "protected port" feature in the switch world.
We're looking at deploying both office extend and also a guest wlan. Both would require a WLC in the DMZ.My question is can one 5508 WLC be both a guest anchor and have office extend APs on it at the same time?
View 2 Replies View RelatedI am using a WLC 5508 and its internal DHCP server. I cant find anywhere I can setup option 43. However, the access points are connected in just fine. Do I need to worry about setting up a seperate DHCP server to get option 43 setup properly?
View 7 Replies View RelatedI will now install a Cisco WLC 2504 and 18 AP´s ( 1142n).
Client has a Cisco infrastruture with Cisco Switch´s 3750x and others.
We expected to have :
1. Managment Vlan to add WLC 2504 and the AP´s ( DHCP server should be reached on this Vlan)
2. Configure a trunk in the switch port where the WLC will connect, allowing vlan´s that we choose to reach.
3. configure WLC ( ssid´s, Vlan´s, interfaces).
4. Configure AP´s.
Is there any basic setup that i missed for things to run ?
Normally I create DHCP reservations for AP`S and for Clients in diferent Vlan´s:
Mgmt Vlan 100: 192.168.0.xx
AP´s vlan 101: 192.168.1.xx
Clients Vlan 102: 192.168.2.xx
All this ones should be created as interfaces on WLC?
I'm trying to verify some behaviors I'm seeing with my 5508 controller setup, I've zero experience with this hardware and clueless on the best practices. With that said... out of the box I ran through the AutoInstall process.
I gave my service port an IP address on my subnet, 10.10.8.0/24 vlan 100 and gave the management interface the ip address 10.10.30.5/24 vlan 130
From my host I can ping the management interace 10.10.30.5 and the interface gateway 10.10.30.1
I cannot connect to the controller via 10.10.30.5 either through the web GUI or telnet
I can connect to the controller via 10.10.8.200 both through the web interface and telnet
while connected to the service port, I can ping the management port IP but I cannot ping the 10.10.30.1 gateway.
We have attached two test 3502I AP's and they found the controller and pulled correct ip addresses, clients can authenticate and access network resources as well as the Internet so for the most part, things are working but it concerns me that the management interface can't ping its own gateway.
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
[Code]......
We are setting up one of these for the first time. It is in a constant rebooting process.
Here is the boot process:
r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000032 0x00000211
using eeprom values
[Code].....
We have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
i have two 1262 one is join ok but one join loop
View 7 Replies View RelatedMy bckup WLC controler seems to stumble in the setting of authentication phase. A week ago I actualy successfully implemented and tested HA scenario with two 5500 controllers (one of them with the HA SKU code). Both of them were upgraded to 7.4.100 version, but today the bckup controller has gone insane! The HA sceanrio was broken down and the bckup controller loops in "Enter credentials" loop forever! It doesn't matter what I enter, how many signs, it just loops endlessly... I bolded the console output underneath... The catch is that it doesn't matter what I put in it yust ignores the input and asks me for credentals again!
Here's some of the output....
Starting WIPS: okStarting SSHPM LSC PROV LIST: okStarting RRC Services: okStarting SXP Services: okStarting Alarm Services: okStarting FMC HS: okStarting IPv6 Services: okStarting Config Sync Manager : okStarting Hotspot Services: okStarting PMIP Services: okStarting Portal Server Services: ok
[Code].....
On a recommendation from a network engineer, I got a used Cisco 891. Having worked with small business routers most of my working life, I thought this should not be a problem. However, I had no clue these things used a console and command line to initialize. I have the console cable, am able to console into the device, but am haphazardly issuing command lines straight out of the PDF manual but cannot get Cisco CP to discover the device.
From what I can tell, I am stuck at the point where the manual tells me to enable http server. I ran the command lines several times, executed write mem where available, but when I run the show services command, http is not enabled.
And if you do refere to command lines, I was reading some other forums and they were speaking of "run this command, run that command" but I could not make out the correct syntax, in what mode, whether it be config or config t, etc. So I might need a wee bit of handholding.
I'm hoping that once I can get Cisco CP or CPE to discover the device, I can make my way through the GUI to configure since those usually do make sense to me. As of now, I'm in the thick of it ...
accounting in ACS 5.3. When I setup accounting on WLC 440x / 5508 ACS takes them as an authentication request and fail.
Here are some logs what I see in acsview:
Dec 9,11 6:05:11.783 PM
Radius authentication failed for USER: navrka2 MAC: a.b.c.d AUTHTYPE: Radius authentication failed
ACS Session ID:
dc2aaa1v/112555963/420
Audit Session ID:
0a9a01d7000001fd4ee23a3d
Tunnel Details:
[code]...
My PC doesn't connect to internet on initial boot, says there is a disconnected cable. On a restart it finds the wirelss card and connects no problem to our BT hub. Tried disabling the wired option, tried a number of things around repairing links etc. but nothing works. it is annoying. PC spec below. Windows 7 is the OS
Giga byte mother board GA-Z68P-DS3
4x4gb of RAM
Intel i5 3.2 CPU
Radeon HD 6770 Graphics card
A wireless adapter TL-WN350GD
A 120 GB SSD hard drive
And a 1TB hard drive
A CnM card reader
Optical DVD drive too
I've bought my E4200v2 via eBay, because original Cisco store doesn't ship to my country (Israel).My first unit was... defective, I think I wrote about the issue on this forum a while ago.It had connection troubles, always in a dead loop, saying "Connecting..." one to 100 times it managed to connect, and suffered slow internet connection speed, where all speedtests gave me 60% of my actual internet speed.Which is 30mbit.I'm sure about my ISP, it uses next.gen technology, they have their own underwater optic cables. Without Cisco router, only dialer, I get 100% of my internet speed, or with another router as well.I decided to RMA my e4200v2.
Out of context question: Why there's no option to specify server name instead of server IP? our ISP uses domain name for connection, rather than IP address, as they have a lot and a load balancer above 'em.Now, to the original issue.Refund is no option, RMA again is no option, too much time and money.Maybe there is a solution? It just can't be the reality, that two out of two units are not working. I heard this router is very good. And I heard the v1 is working very well in Israel. so It can't be our country that is the problem.By the way, I've called my ISP and they've switched me to MPLS connection for a try, so in a router you just switch to "Automatic configuration - DHCP" and it pulls IP, DNS servers and connected to the internet, but was hooooribly slow.
So I'm back to dialer. the main still is the "Connecting..." loop, sometimes says "Connected" for a second, and then connecting again... It manages to pull DNS addresses though, but never the IP and never managed to stay connected.All the connection configs are very basic, you know it. Server IP, username, password, keep-alive, MTU (I've tried auto, and a ton of other combinations recommented by our ISP or Cisco).My latest idea was to film how I burn it or throw a rock at it and send to Cisco the video, but that's kinda too much, it's too early for such decisions, especially when already $300 were spent.
I have a 2811 with CME 8.5; I recently added a SIP trunk and can make & receive calls just fine. I noticed today that when connecting to an external IVR system, I can't send additional tones (press 1 for Sales, for example). I have two DIDs, same provider, both doing the same thing. The config for one of my SIP trunk dial peer and translations are shown here - I think this is what's appropriate to review but can add anything else that's necessary. I've also omitted some dial peers for X11 and international dialing for brevity.
View 2 Replies View RelatedI am on version 8.2(1) of ASA Code.When accessing a SQL server on a secure internal interface,(Traffic is sourcing from DMZ) i'm getting some timeouts on the initial connection on port 1433. All subsequent connections work fine. Packet tracer shows the connection builds properly, and shouldn't have a connectivity issue. The problem server is a webserver that connects back through the firewall to access the SQL server on port 1433. We also have many other webservers in the DMZ which access the same SQL server, but do not have the same timeout issues. Here are my timeouts, from the config
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
arp timeout 14400
I've seen a couple articles about increasing the tcp timeout to 3 hours for the DMZ interface?
I have configured the box and done the usual wr, copy run start, and the box keeps coming up with the initial config dialog?
View 4 Replies View RelatedI have a new pix 515e for Home practice.
1. I couldn't telnet the switch after configuring. should i have to use cross cable or not to connect PC-PIX? (as new switches and routers run through straight cable). more importantly i couldn't even ping the inside ip which is telnet and ssh enabled.
2. Receiving the following after executing each and every command on global mode.
-Configuration Replication is NOT performed From standby Unit to Active Unit
-Configurations are no longer synchronized.
I'm trying to set up a new ASA 5510. I have a pretty simple set up with one /24 on the inside NATed to a DHCP address on the outside. Everything on the inside works and I can ping the outside interface from external devices. No matter what I do I can't get anything internal to route across the border to the outside and back. To try and eliminate ACL issues as a possibility I added permit any any rules to the incoming access lists on the inside and outside interfaces. Here's the sh run.
: Saved
:
ASA Version 8.4(3)
!
hostname gateway
domain-name xxx.local
[code]....
when this error occurs
we can't see the cdp neighbor and the wireless crash.
we login onto the ap with console , we can see the error log : “Network interrupt loop detected” . last forever
Recently I am having a problem during the initial start up. I am running Windows 7. After the computer starts up, I do not have an internet connection. The yellow triangle with an exclamation mark in it appears in the bottom right on the monitors. I can go to the internet connections and disable, then enable and my connection returns. This is only happening during the initial start up. This happens 3 out of 4 times during start up. I have had the cable company check everything and they are saying it is an issue with my computer.
View 1 Replies View Related