Cisco Wireless :: HA On WLC 5500 - Setting Username Loop
May 5, 2013
My bckup WLC controler seems to stumble in the setting of authentication phase. A week ago I actualy successfully implemented and tested HA scenario with two 5500 controllers (one of them with the HA SKU code). Both of them were upgraded to 7.4.100 version, but today the bckup controller has gone insane! The HA sceanrio was broken down and the bckup controller loops in "Enter credentials" loop forever! It doesn't matter what I enter, how many signs, it just loops endlessly... I bolded the console output underneath... The catch is that it doesn't matter what I put in it yust ignores the input and asks me for credentals again!
Here's some of the output....
Starting WIPS: okStarting SSHPM LSC PROV LIST: okStarting RRC Services: okStarting SXP Services: okStarting Alarm Services: okStarting FMC HS: okStarting IPv6 Services: okStarting Config Sync Manager : okStarting Hotspot Services: okStarting PMIP Services: okStarting Portal Server Services: ok
[Code].....
View 3 Replies
ADVERTISEMENT
Mar 4, 2013
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
[Code]......
View 15 Replies
View Related
May 8, 2013
We are setting up one of these for the first time. It is in a constant rebooting process.
Here is the boot process:
r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000032 0x00000211
using eeprom values
[Code].....
View 3 Replies
View Related
Jan 24, 2012
We have a few AIR-LAP1041N-E-K9 and 2106 controller. One of the 1041N began rebooting in a loop. All over AP work fine. This morning, AP normally loaded at once. Two hours later, after AP reboot, situation repeated itself. Output from console:
using eeprom values
WRDTR,CLKTR: 0x85000800 0xc0000000
RQDC ,RFDC : 0x80000037 0x0000018c
[Code].....
View 4 Replies
View Related
Mar 18, 2013
i have two 1262 one is join ok but one join loop
View 7 Replies
View Related
Apr 5, 2013
I have a new from the box 5508 which I am attempting to follow the initial setup process to IP it. When I make it through the initial setup the box reboots buts brings me back to the "terminate auto-install" prompt again for some weird reason?
View 2 Replies
View Related
Mar 26, 2012
I've bought my E4200v2 via eBay, because original Cisco store doesn't ship to my country (Israel).My first unit was... defective, I think I wrote about the issue on this forum a while ago.It had connection troubles, always in a dead loop, saying "Connecting..." one to 100 times it managed to connect, and suffered slow internet connection speed, where all speedtests gave me 60% of my actual internet speed.Which is 30mbit.I'm sure about my ISP, it uses next.gen technology, they have their own underwater optic cables. Without Cisco router, only dialer, I get 100% of my internet speed, or with another router as well.I decided to RMA my e4200v2.
Out of context question: Why there's no option to specify server name instead of server IP? our ISP uses domain name for connection, rather than IP address, as they have a lot and a load balancer above 'em.Now, to the original issue.Refund is no option, RMA again is no option, too much time and money.Maybe there is a solution? It just can't be the reality, that two out of two units are not working. I heard this router is very good. And I heard the v1 is working very well in Israel. so It can't be our country that is the problem.By the way, I've called my ISP and they've switched me to MPLS connection for a try, so in a router you just switch to "Automatic configuration - DHCP" and it pulls IP, DNS servers and connected to the internet, but was hooooribly slow.
So I'm back to dialer. the main still is the "Connecting..." loop, sometimes says "Connected" for a second, and then connecting again... It manages to pull DNS addresses though, but never the IP and never managed to stay connected.All the connection configs are very basic, you know it. Server IP, username, password, keep-alive, MTU (I've tried auto, and a ton of other combinations recommented by our ISP or Cisco).My latest idea was to film how I burn it or throw a rock at it and send to Cisco the video, but that's kinda too much, it's too early for such decisions, especially when already $300 were spent.
View 9 Replies
View Related
Jun 7, 2013
when this error occurs
we can't see the cdp neighbor and the wireless crash.
we login onto the ap with console , we can see the error log : “Network interrupt loop detected” . last forever
View 3 Replies
View Related
Dec 5, 2011
My WRT310n router, since yesterday, stopped working "normally".It was disconnected from the power plug in order to put it in another shelve and when I plugged it in, voilá, constant reboot.I keeps rebooting forever... I can't even make an ethernet connection. Reboot, after reboot. Tryied to make a reset with no luck, 5 seconds reset, 30s reset, pressing reset while plugging it in.Even with nothing connected to it (neither wireless nor lan), just the power plug and it keeps re booking one after another.
View 2 Replies
View Related
Mar 23, 2011
I forgot my username and password how can i retrieve my username and password,, i forgot to put password for connection on my wifi.
View 1 Replies
View Related
Feb 23, 2012
We have 4 SSID's established for our staff, students, Guests and Providers. CISCO / ARUBA Managed APs with a centralized CISCO Controller. Can I restrict access by the first letter in the username so that usernames that begin with x will ONLY connect to the Staff SSID if in range and usernames starting with y ONLY connect to the student SSID?
View 1 Replies
View Related
Nov 22, 2012
the default username and password for the below WLC device
Model :
AIR-CT5508-100-K9
Image : AIR-CT5500-K9-7-0-230-0.aes
View 9 Replies
View Related
Aug 1, 2012
Running 7.0.220. There are several 'unknown' users every day reported in WCS. Investigating the connections on the WLC I find the clients are in a run state and passing traffic but there is no username listed on the client detail. (hence the unknown on WCS)
(mcm-189jsoc-wlc1) >show client detail 60:c5:47:07:b6:5a
Client MAC Address............................... 60:c5:47:07:b6:5a
Client Username ................................. N/A
AP MAC Address................................... 00:1e:13:42:16:a0
AP Name.......................................... mcm-208dorm-wap1
[code].....
Clients in this state are usually Apple products. From initial investigation it looks like the do authenticate with the ACS. r debugs to run, or fixes on the WLC? Perhaps there's a bug on this behavior?
View 11 Replies
View Related
Sep 8, 2010
I have a Cisco Wireless Router, Model # WRT160N. I had initally installed it to a laptop. I have a new PC which I am trying to install it to. Unfortunately, when I installed it to the laptop, I put in a new Username and Password. When I tried to install it to the PC, it gets to point of trying to read the router and then gives me the error message "Needs Factory installed Username and Password". I went to the IP site and tried to see where I could delete my Username and Password and reinstall the Factory defaults but cannot locate it.
View 2 Replies
View Related
May 8, 2013
I have a problem with my linksys WRT54GL router. I entered here [URL] and i set it up, i can connect to internet on my PC and wireless works great but i can't set wireless password and name. When i go to the wireless tab, i write the new name but when i hit seve setting i get disconnected from internet. I try to go to status and click on Connect tab, when is connected internet works but the name and the password of the wireless that i set earlier is reset to default. What do i have to do to set name and password and have internet at the same time.
View 7 Replies
View Related
Oct 16, 2012
I am trying to figure out my WEP code to use to connect to XBOX LIVE. To log on to my internet we just have a WPA-Personal I think, so I have been trying to sign into my router to hopefully obtain my WEP key there, but cannot sign in. I have tried every combination of usernames and passwords such as:
[none] admin
admin admin
[none] [none]
n/a ... and more but nothing works.
View 1 Replies
View Related
Aug 17, 2011
I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck.
I also have a Cisco Aironet AP1242AG that is doing the same thing.
View 7 Replies
View Related
Jan 3, 2013
I am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages)
*Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
[code]....
View 2 Replies
View Related
Jun 25, 2010
Recently I have purchased two brand new wap4410n access points.
I have connected my computer directly to one of the access points, and attempted to connect to the Web Configuration utility through my web browser.
I'm using a: 09' MacBook Pro, running Snow Leopard and Safari 5.
I can access the login screen of the access point, although when I enter the default username: admin and password admin, the login screen returns an error: Invalid username and/or password (or something to that effect). The URL changes to: http://192.168.1.245/login.htm&no=3.
I have reset the device by holding in the reset button for thirty seconds, powered down, powered up and re-attempted to login.
I still get the same error as above.
I have attempted to access the Web Configuration utility on both access points, and both access points provide the same error. I have also tried using the username: cisco and password: cisco.
Cisco, when contacted, said both access points must be faulty and I should replace them.
The probability of such an occurrence happening with two devices seems very low, and leads me to think there must be other factors at play. The only constant I can think of is the fact I'm using the same computer to access the devices.
View 4 Replies
View Related
Feb 19, 2012
I have a 5508 WLC running 6.0.202.0. It functions as the Anchor Controller for the guest network. It sits in our Internet DMZ and is isolated from the rest of the network. It does not connect to AD, ACS, etc. The guest wireless WLAN is configured for Web Policy - Authentication. I have a customized login page. Credential management is done by WCS.
Users are connecting to the guest wireless network and entering their creds with no issues using mobile devices (iPad, etc). Then the mobile device goes to sleep / turns off and when they go to use it again, they have to type their creds in again. They dont like retyping their creds throughout the day.
good way mitigate the multiple logins? Something like a 'save password' option on the customized page?
View 5 Replies
View Related
Jul 18, 2011
A username and password are being requested by http://192.168.1.1. The site says: "E1000"
View 1 Replies
View Related
Mar 18, 2013
I have tried using my router name and password when you 1st connect and got nothing.I have held the reset button for a minute straight to try and restore default settings and have got nothing. I'm trying to enter my ISP into the web browser
View 2 Replies
View Related
Jul 1, 2012
I'm not a very knowledgeable person when it comes to networking stuff so ill try and explain this the best I can.I have a Cisco router the number on it is EPC2425.I set a user name and password I've long forgotten for access to the web based security protocols for the modem and if there was one I've lost the disk for the control protocol program.I need to get to the port forwarding a such on there and I have no way to a present.
View 4 Replies
View Related
Jul 11, 2009
I am trying to access my Wireless router via 192.168.1.1 When it asks for username and password i did..
Username: (BLANK)
Password: admin
But it didn't work, i think i may have changed the password at one time but im not sure. Is there anyway to check the password and username?
View 5 Replies
View Related
Dec 21, 2011
I would like to enable VPn in WRT54G.Cann't find where to set up user name & psw.Is client necessary to set up user name & psw if there was no need to set up user name & psw for in WRT54G ?
View 3 Replies
View Related
Feb 17, 2012
I just dug my router (wrt54g) out of the closet and hooked it up but I cant remember my name or password for the router. Is there anything I can do that doesn't involve paying linksys any sort of "fee"
View 2 Replies
View Related
Apr 17, 2012
how to change username admin to something different. I can reset the router password but there's no easily identifiable option for changing the username.
View 5 Replies
View Related
May 14, 2013
is there anyway to configure a certificate between the wireless AP and clients to secure my username and the password.
my setup is WLC5508/AP1142/ACS5.4
View 6 Replies
View Related
Dec 27, 2012
All my switches were connected together as ring topology. We use REP to block redundancy link.One of my colleagure was setting up a new link(VLAN) for one customer which was then caused a L2 loop. The CPU was hitting 100% and REP started to lost neighbors then we had a big outage.I am thinking to deploy QoS on all REP switch (on trunk links from switch to switch) to give priority to control traffic like REP and some importance data VLAN. Of course,Storm-Control already implemented on all access-port.
View 2 Replies
View Related
Feb 6, 2012
i want to change my username and password of my router cw-5354 of cd-r king but the default user and password doesn't work anymore so i can't access the control panel.
View 3 Replies
View Related
Aug 26, 2012
I am looking to get access to an external hard drive that I have set up on my wireless network.When I try to do an automated Windows backup (off my Vista based laptop files) on to an external hard drive which is connected to my wireless network (through a Belkin router) I am being asked for a user name and password to access the connected hard drive on the network. The thing is that I don't remember setting up a username and password for the hard drive at all. I can paste single files mannually onto the external hard drive without being asked for a username and password. I did perform an automated Windows backup off my other Windows 7 laptop and was not ask for a username and password. where to find the username and password information ?
View 3 Replies
View Related
Apr 22, 2012
I use an internet network via wifi that require username and password. The router for wifi network in my place and i connect my cisco(linksys wrt320n) to the router. Every time i want to connect to internet i have to enter my username and password.I try to configure my cisco modem but there is no result. Is there any way or program to automatically enter the username and password?
View 3 Replies
View Related
Sep 1, 2006
I get into the router ok, using no username and "admin" for password.I set up the key, hit OK, then when I hit "apply" the prompt comes up for the username and password again. I skip the username, enter "admin" for password (just like I did getting into the setup earlier) except now it says it doesn't recognize, or it's invalid, etc.
View 9 Replies
View Related
