Linksys Wireless Router :: EPC2425 - Lost Username And Password
Jul 1, 2012
I'm not a very knowledgeable person when it comes to networking stuff so ill try and explain this the best I can.I have a Cisco router the number on it is EPC2425.I set a user name and password I've long forgotten for access to the web based security protocols for the modem and if there was one I've lost the disk for the control protocol program.I need to get to the port forwarding a such on there and I have no way to a present.
I have a problem with my linksys WRT54GL router. I entered here [URL] and i set it up, i can connect to internet on my PC and wireless works great but i can't set wireless password and name. When i go to the wireless tab, i write the new name but when i hit seve setting i get disconnected from internet. I try to go to status and click on Connect tab, when is connected internet works but the name and the password of the wireless that i set earlier is reset to default. What do i have to do to set name and password and have internet at the same time.
I am trying to figure out my WEP code to use to connect to XBOX LIVE. To log on to my internet we just have a WPA-Personal I think, so I have been trying to sign into my router to hopefully obtain my WEP key there, but cannot sign in. I have tried every combination of usernames and passwords such as:
I have tried using my router name and password when you 1st connect and got nothing.I have held the reset button for a minute straight to try and restore default settings and have got nothing. I'm trying to enter my ISP into the web browser
I would like to enable VPn in WRT54G.Cann't find where to set up user name & psw.Is client necessary to set up user name & psw if there was no need to set up user name & psw for in WRT54G ?
I just dug my router (wrt54g) out of the closet and hooked it up but I cant remember my name or password for the router. Is there anything I can do that doesn't involve paying linksys any sort of "fee"
I use an internet network via wifi that require username and password. The router for wifi network in my place and i connect my cisco(linksys wrt320n) to the router. Every time i want to connect to internet i have to enter my username and password.I try to configure my cisco modem but there is no result. Is there any way or program to automatically enter the username and password?
I get into the router ok, using no username and "admin" for password.I set up the key, hit OK, then when I hit "apply" the prompt comes up for the username and password again. I skip the username, enter "admin" for password (just like I did getting into the setup earlier) except now it says it doesn't recognize, or it's invalid, etc.
How do I change the username password in the router settings for the linksys ea4500? It only lets me change the password, I cant find an option to change the username.
I successful set up my WRT54GR router. Now I want to add a new device but can't find or remember my user name and password. So I decided to reinstall the router only to find that the http://192.168.1.1 page asks me for my admin password - having sensibly created one 4 years ago which I have now forgotten or where I wrote it down. How the hell do I get around this - if at all or do I have to buy a new router and start all over again!
The EA4500 web-settings application asks for a username and password. The username is "admin" and the password is my long (60 character) wpa key. I see where I can change the password but it says I'll lose all wireless connections. This doesn't make sense to me. I would think the router administration username and password are completely separate from the ssid and wpa key. This was the case with my earlier LinkSys router. I'd like a router administration username to be something other than the generic "admin" and a password that is easier than my long wpa key. I want a separate ssid and wpa key (what I currently have).
I want to upgrade the firmware for the router wrp400 , i am asked Username & Password in order to update the firmware.I tried admin/admin does not work. I tried to reset the router, same thing, I have no ISP user and password.
I changed my E1000 router name successfully, and then went into the Administration section to change my password. After changing the password and clicking on Save a small screen pops up asking me to verify my router's username and password. When I enter the exact same user name and password it does not accept them. When I try to enter the old user name and password it does not accept them either. I then try combinations of the two and it still will not accept the input. I have reset my router 4 times now and this keeps occurring. I am completely baffled.
I upgraded my Mac OS to 10.7 (lion). I can no longer use Cisco Connect. I cannot recall the password I created when using Cisco Connect prior to upgrading to Lion. Is there any way to determine or reset my password without Cisco Connect. And why is it taking Cisco so long to provide firmware that works with Mac OS 10.7?
I haven't used my Linksys WRT54G v5 wireless router for about 1 1/2 years and needed it now at a new place.I set a user name and password I've long forgotten for access to the web based security protocols for the modem and I've lost the disk for the control protocol program.I tried pressing the reset button to clear the modem and it took the WPA protocol off the modem so I can use it without any security but that's not a good thing.How do I get it freed up so I can get to the security protocols and put security back on my modem?
Alright, the computer I had cisco connect on crashed. I got a new computer and I'm trying to install Cisco connect using the downloaded version and I can't install it because it requests the password of the router, which i do not know. This is because I've lost the CD copy of Cisco connect. I've tried resetting the router itself by pressing the red reset button
I purchased a used WRT54G router that has DD-WRT firmware installed. I do not have the user name and password for it. How do I get around that issue so I can set the router up on my network. I would like to keep the DD-WRT firmware.
i want to change my username and password of my router cw-5354 of cd-r king but the default user and password doesn't work anymore so i can't access the control panel.
i just pickup a linksys wrt54gs v5 and I cannot log into it. I reset the modem and tried to log in with the default usr/pass ( usr= leave blank , pass= admin) and it is still not working . I also tried other combination of admin, administraror, password and still nothing. Any usr/password that might work? Also I though of I might get around this problem by flashing to dd-wrt or tomato do I need to do anything in webadmin to do this?
I needed to bring my laptop Toshiba satellite A135 - S4404 computer back to factory settings. When I did I lost my internet connection. I have a wireless G router. I tried setting up a new connection. When I couldnt remember my username and password to the linksys, I made several attempts to give them one.A fool hearty effort on my part. They locked me out. I was given a red X on that particular network. How to get back to where I can give them the necessary username and password?I believe I found it written on my Linksys user guide.
I cannot access the Username and password on my WAG160N - the ones I thought were correct do not accepted, nor are the quoted 'defaults'.I have tried holding down 'reset' for 30 secs; I have tried powercycling the router after and during this; I have tried 'resetting' with the phone and ethernet connections unplugged. This is NOT returning the machine to the default settings - and neither is it 'wiping' the existing settings for my ISP.The amusing thing is - it works perfectly well, but I can't alter my security settings and I can't alter other settings if I change my ISP (as I was intending to do).
I want to access my wireless router settings but i don't know my username or pass its my network however I can't access it. Is there a way to retrieve it?
