I want to upgrade the firmware for the router wrp400 , i am asked Username & Password in order to update the firmware.I tried admin/admin does not work. I tried to reset the router, same thing, I have no ISP user and password.
I'm currently trying to upgrade my linksys WRT54G v1.1 router using the WRT54G-EU_fw,0 file, however when I press upgrade it comes up with a message saying "Incorrect Image File!". The current firmware version is v1.42.2 Is there any way to fix this so I can upgrade it?
I am looking to get access to an external hard drive that I have set up on my wireless network.When I try to do an automated Windows backup (off my Vista based laptop files) on to an external hard drive which is connected to my wireless network (through a Belkin router) I am being asked for a user name and password to access the connected hard drive on the network. The thing is that I don't remember setting up a username and password for the hard drive at all. I can paste single files mannually onto the external hard drive without being asked for a username and password. I did perform an automated Windows backup off my other Windows 7 laptop and was not ask for a username and password. where to find the username and password information ?
I just installed the firmware upgrade 3.0.03 for my WRP160N router. It is now not accepting my Admin password. Nothing else has changed expect network name now shows linksys and not my assigend network name (SSID)
I recently purchased a new Cisco 881w router (last Friday).I have configured the 'wired' part of the router with little trouble, but the wireless side is proving a little challenging.I have read a number of posts complaining about the firmware version installed on my device being very buggy.The version of the firmware on the wired part is: Version 15.0(1)M8, however, the firmware on the wireless side seems to be: Version 12.4(21a)JA1 - the version reported as buggy. The former has a version date of 2012, with the latter being 2009.I have tried to download a newer version, but the site is asking me to provide a support contract.I wouldn't mind buying a support contract if the thing worked in the first place and I was trying to add some feature after it had been working for a while.
I am attempting to install an HP Photosmart 7515 eAll-in-One Printer. Works OK in the USB "tethered" mode, as a one-computer printer only. It will not install as a wi-fi device, probable reason being the settings on my (wireless) router, according to the printer's Wireless Network Test Results sheet. I suspect that the firmware on it (3.0.02) is obsolete. What is the latest firmware version for the WRT160N ?
I have a problem with my linksys WRT54GL router. I entered here [URL] and i set it up, i can connect to internet on my PC and wireless works great but i can't set wireless password and name. When i go to the wireless tab, i write the new name but when i hit seve setting i get disconnected from internet. I try to go to status and click on Connect tab, when is connected internet works but the name and the password of the wireless that i set earlier is reset to default. What do i have to do to set name and password and have internet at the same time.
I am trying to figure out my WEP code to use to connect to XBOX LIVE. To log on to my internet we just have a WPA-Personal I think, so I have been trying to sign into my router to hopefully obtain my WEP key there, but cannot sign in. I have tried every combination of usernames and passwords such as:
I have tried using my router name and password when you 1st connect and got nothing.I have held the reset button for a minute straight to try and restore default settings and have got nothing. I'm trying to enter my ISP into the web browser
I'm not a very knowledgeable person when it comes to networking stuff so ill try and explain this the best I can.I have a Cisco router the number on it is EPC2425.I set a user name and password I've long forgotten for access to the web based security protocols for the modem and if there was one I've lost the disk for the control protocol program.I need to get to the port forwarding a such on there and I have no way to a present.
I just dug my router (wrt54g) out of the closet and hooked it up but I cant remember my name or password for the router. Is there anything I can do that doesn't involve paying linksys any sort of "fee"
I use an internet network via wifi that require username and password. The router for wifi network in my place and i connect my cisco(linksys wrt320n) to the router. Every time i want to connect to internet i have to enter my username and password.I try to configure my cisco modem but there is no result. Is there any way or program to automatically enter the username and password?
I get into the router ok, using no username and "admin" for password.I set up the key, hit OK, then when I hit "apply" the prompt comes up for the username and password again. I skip the username, enter "admin" for password (just like I did getting into the setup earlier) except now it says it doesn't recognize, or it's invalid, etc.
I successful set up my WRT54GR router. Now I want to add a new device but can't find or remember my user name and password. So I decided to reinstall the router only to find that the http://192.168.1.1 page asks me for my admin password - having sensibly created one 4 years ago which I have now forgotten or where I wrote it down. How the hell do I get around this - if at all or do I have to buy a new router and start all over again!
The EA4500 web-settings application asks for a username and password. The username is "admin" and the password is my long (60 character) wpa key. I see where I can change the password but it says I'll lose all wireless connections. This doesn't make sense to me. I would think the router administration username and password are completely separate from the ssid and wpa key. This was the case with my earlier LinkSys router. I'd like a router administration username to be something other than the generic "admin" and a password that is easier than my long wpa key. I want a separate ssid and wpa key (what I currently have).
Just set-up a new X2000, loaded latest firmware 2.0.01, configured it via the web UI ('Browser based utility' as per the manual). Connected OK to my ADSL broadband by O2. Configured wireless, everything OK. Funny it doesn't need a user name, only a password, my prevoius WAG160N could be configured for both.Now I want to configure the Parental Controls, BUT apart from my computer name and an Android phone name, all I see in the Target Device ADD button pop-up are a list of repeated 'Network Device'. There seems no way to be able to distinguish which is which device (mix of XP & Win 7 PC's and HP Printer through a separate switch), as it does not show IP address or MAC.
I thought I may have better luck with the Cisco Connect software (which I didn't use to set-up the router). I downloaded the latest version 1.4.11194.0, and ran this on another computer with wireless. Apart from reconfiguring my static IP address to DHCP, and then connecting through DHCP, the software said it could not configure my router. So it never gets to a point where it installs any program on the computer so that I can configure Parental Controls. How do I get the router to show ALL the computer names in the list rather than 'Network Device' or is there a way to distinguish which 'Network Device' is which computer?
My linksys 4200 was set up some time ago for me, (unsecured) and was working fine. I was having problems with just 1 desktop that was using a usb wireless adapter, so I went and purchased a new cisco ae2500. While connecting I used the push button that it described, only it knocked out the network, and all the other computers are now off of the network. The new network(s) are Cisco_WPS_42526 (secure) and Cisco_WPS_42526-guest. Not knowing the network key and the guys that set it up are gone, I tried the guest. WHICH REQUIRES A PASSWORD!!!! I can now not get ANY of my computers online! How do I find the security, or the password? Why would you need a password for an insecure network anyway?
I changed my E1000 router name successfully, and then went into the Administration section to change my password. After changing the password and clicking on Save a small screen pops up asking me to verify my router's username and password. When I enter the exact same user name and password it does not accept them. When I try to enter the old user name and password it does not accept them either. I then try combinations of the two and it still will not accept the input. I have reset my router 4 times now and this keeps occurring. I am completely baffled.
I recently moved to a cable ISP and unfortunately had to also change routers in order to take advantage of the VoIP feature (analog phone) they provided me with.Now, the new router, the WRP400, is very limited feature-wise compared to the custom flashed WRT54GL I used to use with my DSL provider.Now the WRT54GL does not have any FXS ports, so I obviously can't just plug my cable modem to the WRT54GL. Therefore, I was hoping to achieve a setup similar to this one:Cable modem => VoIP Router w/ voice only (WRP400) => "Main" router (WRT54GL w/ Tomato)Is there a way to bridge the WRP400 successfully with the WRT54GL keeping only the voice feature enabled on the VoIP router while the WRT54GL takes care of the rest? (Wireless, WAN, port forwarding, etc)
I just purchased a new E1200 router with firmware version 2.0.01 and downloaded the latest version 2.0.03 and tried to install it through the router. When I choose the downloaded file and try to start upgrade I immediately get an error "The Image File is Incorrect". I redownloaded it and tried again with the same error. how to get past this and upgrade the firmware?
The file uploads fine, but I get an error message saying the router can't be updated atthe moment. I want to do the update because as of now, the router can't see my drive connected on usb (one ntfs partition and another one called wbfs, maybe that one is causing the issue about the drive).
I tried to upgrade my router firmware to the latest 18.104.22.168204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
I currently have Model name: Linksys E4200 Firmware version: 1.0.04 build 11 Software version: 1.4.12100.0
I'm trying to upgrade to the second and most up to date version. (Version: 2.0) firmware. Any links or way to do this? I tried doing it through my router settings under administration -> firmware upgrade but it won't update automatically. I have to find the actual update file and update the firmware through that.