I am in the process of upgrading a Linksys WRT160Nv2 to a Cisco E4200. I run Cisco Connect and enter my ISP password (7 characters long) and click save but when it refreshes the screen, the password field has 16 characters in it.
I have a problem with my linksys WRT54GL router. I entered here [URL] and i set it up, i can connect to internet on my PC and wireless works great but i can't set wireless password and name. When i go to the wireless tab, i write the new name but when i hit seve setting i get disconnected from internet. I try to go to status and click on Connect tab, when is connected internet works but the name and the password of the wireless that i set earlier is reset to default. What do i have to do to set name and password and have internet at the same time.
I am trying to figure out my WEP code to use to connect to XBOX LIVE. To log on to my internet we just have a WPA-Personal I think, so I have been trying to sign into my router to hopefully obtain my WEP key there, but cannot sign in. I have tried every combination of usernames and passwords such as:
I have tried using my router name and password when you 1st connect and got nothing.I have held the reset button for a minute straight to try and restore default settings and have got nothing. I'm trying to enter my ISP into the web browser
I'm not a very knowledgeable person when it comes to networking stuff so ill try and explain this the best I can.I have a Cisco router the number on it is EPC2425.I set a user name and password I've long forgotten for access to the web based security protocols for the modem and if there was one I've lost the disk for the control protocol program.I need to get to the port forwarding a such on there and I have no way to a present.
I just dug my router (wrt54g) out of the closet and hooked it up but I cant remember my name or password for the router. Is there anything I can do that doesn't involve paying linksys any sort of "fee"
I use an internet network via wifi that require username and password. The router for wifi network in my place and i connect my cisco(linksys wrt320n) to the router. Every time i want to connect to internet i have to enter my username and password.I try to configure my cisco modem but there is no result. Is there any way or program to automatically enter the username and password?
I get into the router ok, using no username and "admin" for password.I set up the key, hit OK, then when I hit "apply" the prompt comes up for the username and password again. I skip the username, enter "admin" for password (just like I did getting into the setup earlier) except now it says it doesn't recognize, or it's invalid, etc.
I successful set up my WRT54GR router. Now I want to add a new device but can't find or remember my user name and password. So I decided to reinstall the router only to find that the http://192.168.1.1 page asks me for my admin password - having sensibly created one 4 years ago which I have now forgotten or where I wrote it down. How the hell do I get around this - if at all or do I have to buy a new router and start all over again!
The EA4500 web-settings application asks for a username and password. The username is "admin" and the password is my long (60 character) wpa key. I see where I can change the password but it says I'll lose all wireless connections. This doesn't make sense to me. I would think the router administration username and password are completely separate from the ssid and wpa key. This was the case with my earlier LinkSys router. I'd like a router administration username to be something other than the generic "admin" and a password that is easier than my long wpa key. I want a separate ssid and wpa key (what I currently have).
I want to upgrade the firmware for the router wrp400 , i am asked Username & Password in order to update the firmware.I tried admin/admin does not work. I tried to reset the router, same thing, I have no ISP user and password.
I changed my E1000 router name successfully, and then went into the Administration section to change my password. After changing the password and clicking on Save a small screen pops up asking me to verify my router's username and password. When I enter the exact same user name and password it does not accept them. When I try to enter the old user name and password it does not accept them either. I then try combinations of the two and it still will not accept the input. I have reset my router 4 times now and this keeps occurring. I am completely baffled.
I have a WRT160Nv2 and I have a stack of 5 static ip addresses. I have the entire store wired and everything is working great, except my DVR. I cannot get it to work on the network. Should I use one of the static ip's or not?
Unable to get Nanostation GUI when it is connectedI have a smart panel in the basement of my house which has a WRT160Nv2 in it. Connected to it in one port is a WRT610N which is on the second floor. Heres my issue now, for my main and computer rooms they are running off of one switch right (I'm not sure the IP of it or even how to find the IP of it) but basically any device connected to the smart panel router via ethernet cable is not recieving internet, devices connected wirelessly are.
I have a computer that is connected to a linksys wireless router model WRT160NV2. I also have a laptop. I have never set up a lock or anything on my wireless connection and I think other people are using it. When I type the IP address 192.168.1.1 on my laptop, I do not get the screen to pop up to change my settings. Do I need to do this from the computer?
how i can change WRT160Nv2 settings if i cannot find it with default 192.168.1.1;i'm using it as secondary router connected to FIOS actiontec primary, which has the 192.168.1.1; factory default reset linksys to that same IP, can't get it.cannot get internet without actiontec as its coax connected, and linksys doesn't have coax port.can'ty open configure page without internet connection, i believe.tried to use a neighbor's wireless but that's using 192.168.1.1 as well, can't log in to that.this started with firmware upgrade of linksys which left it invisible; didn't complete the upgrade, i don't think. but i've reset it and still nothing.
I Have a WRT160Nv2 and I am trying to get my nat to become unstrict for xbox live. I have tried port fowarding that has not worked. I tried this site [URL] and that didnt work(I only have one xbox 360 btw). Nothing has worked for me and every time I mess with something it screws up the internet so I have to set it up to the previous defaults. I know how to access my router I just need to know what to enable, disable, or add to the router.
So I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.
i just pickup a linksys wrt54gs v5 and I cannot log into it. I reset the modem and tried to log in with the default usr/pass ( usr= leave blank , pass= admin) and it is still not working . I also tried other combination of admin, administraror, password and still nothing. Any usr/password that might work? Also I though of I might get around this problem by flashing to dd-wrt or tomato do I need to do anything in webadmin to do this?
I needed to bring my laptop Toshiba satellite A135 - S4404 computer back to factory settings. When I did I lost my internet connection. I have a wireless G router. I tried setting up a new connection. When I couldnt remember my username and password to the linksys, I made several attempts to give them one.A fool hearty effort on my part. They locked me out. I was given a red X on that particular network. How to get back to where I can give them the necessary username and password?I believe I found it written on my Linksys user guide.
I cannot access the Username and password on my WAG160N - the ones I thought were correct do not accepted, nor are the quoted 'defaults'.I have tried holding down 'reset' for 30 secs; I have tried powercycling the router after and during this; I have tried 'resetting' with the phone and ethernet connections unplugged. This is NOT returning the machine to the default settings - and neither is it 'wiping' the existing settings for my ISP.The amusing thing is - it works perfectly well, but I can't alter my security settings and I can't alter other settings if I change my ISP (as I was intending to do).
i was looking at my network settings today on my pc and noticed a router (linksys wrt160nv2) that wasn't mine. i can right click on it and see its mac address but when i double click it asks me for a pin number. the device shows up with both a wired and wireless connection. i'm using windows 7 64-bit.