We have 4 SSID's established for our staff, students, Guests and Providers. CISCO / ARUBA Managed APs with a centralized CISCO Controller. Can I restrict access by the first letter in the username so that usernames that begin with x will ONLY connect to the Staff SSID if in range and usernames starting with y ONLY connect to the student SSID?
View 1 RepliesI have set up access restriction times for my son (we have wireless access for all systems). I use the MAC address on his systems. Xbox, Kindle Fire and his Laptop. The MAC address are Correct. Here is the problem:
I set the "allow" and times from 6pm - 11:00 pm (while on xmas vacation) - the system works for a while he is shut off as i would like but....
After a period of time the entire house goes off line. I have to reboot the power on e2000 router and then disable the access restrictions. System then works. Problem is repeatable. What is the deal. I have updated firmware already. Otherwise the system works great. Never dies. Just when i set access restricions for a SPECIFIC time it kills entiore houese. BTW i can deny him outright 24/7 and the system idsables his access fine. Its just when i set specific times
My Wireless-N Home Router WRT120N with version 1.0.07 seems to have a problem blocking Sites through scheduling with Access Restriction "Allow" ...I notice that... when I enable access restriction, with policy and some range of computers connecting to my router , and set it to "allow" from "monday - friday" from "8am-6pm" .. with a purpose of blocking some social networking sites, example facebook, It works perfectly fine. But when the "scheduled" time comes ( before 8am and after 6pm ).. I cannot access the internet.. router is working, it detects my modem.. but no internet connection. It always happen before and after the "scheduled time" before the configured access restriction takes over. I have to disable the Access Restriction to continue our internet access.
View 4 Replies View Relatedtarget 192.168.0.21following are rules of access restriction on WRT54G1.rule A- 07:00am~10:00am,internet access allowed, keyword blocked such as Facebook,mail.2.rule B- 10:05am~10:00am,internet access allowed, no keyword blocked.but 192.168.0.21 fails to access internet after rule A expired.
View 1 Replies View Relatedwe upgraded our router from WRT54G V5.0 to WRT110. before we dont have any issues using the ACCESS RESTRICTION from WRT54G but now on WRT110 we encounter a GLOBAL BUG. we are blocking the website like Youtube, Friendster, Facebook etc. on the EDIT LIST TAB we specify 4 IP Address that will not going to access the said websites. The problem is...all Computers (about 15 PC) that are using the Internet cannot access the said website also but we did not enter the other IP's.
View 9 Replies View RelatedI tested this with my laptop by setting its access restriction/parental control to always not access the internet. But still my laptop can still search through Wikipedia. Is this because of the router firmware? By the way I'm using the latest Connect cloud firmware.
View 7 Replies View RelatedI have a WRT110 and in the access restriction settings section the time is in military. I try to set the restriction from 11:30 pm to 6:00 am. I cannot because it tells me the second time "6:00 am" has to be larger than the first. I don't understand a way around this.
View 2 Replies View RelatedAll the documentation for this router shows the Access Restriction tab in the router configuration menu. It's the same as other linksys routers. The current version of the firmware doesn't have this functionality. Was it removed?
View 5 Replies View RelatedI recently mapped my media player's internal hd to my Win 7 system. I'd like to change the drive letter I assigned to something else but I can't find how to do it.
View 2 Replies View RelatedI am trying to create a user restriction to allow one user to access only two networks (10.192.3.0 and 10.192.5.0) I have range of networks but I want to permit only two networks for limited user and full access for the admins. I know this was possible with ACS 3.3 but I am not too sure if this is also applicable with ACS 5.2.
View 1 Replies View RelatedOne of my Clients just aquired a CISCO ASA firewall, and they would like to restrict internet access, that is they want to block internet for Junior employees while managemnet remains connected, Looking at the situation, The ASA serves as the gateway,I tried an Access list like below for one pc to test if it works but instead everyone just went off, may be i misfired somehwere.
Access-list 110 deny tcp any host 192.168.20.100 eq wwwAccess-list 110 deny tcp any host 192.168.20.100 eq 443Access-list 110 permit tcp any any eq wwwAccess-list 110 permit tcp any any eq 443access-group 110 in interface inside
I am looking to get access to an external hard drive that I have set up on my wireless network.When I try to do an automated Windows backup (off my Vista based laptop files) on to an external hard drive which is connected to my wireless network (through a Belkin router) I am being asked for a user name and password to access the connected hard drive on the network. The thing is that I don't remember setting up a username and password for the hard drive at all. I can paste single files mannually onto the external hard drive without being asked for a username and password. I did perform an automated Windows backup off my other Windows 7 laptop and was not ask for a username and password. where to find the username and password information ?
View 3 Replies View RelatedI am resetting my Aironet 1231-G access points and cannot access the default username and password. Here is the information I am getting on the Console. I reset getting the amber light. Attempt to use Cisco as the Username and Password. It replies that authentication fails with the below log information.
*Mar 1 00:00:04.591: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed*Mar 1 00:00:05.868: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0*Mar 1 00:00:05.969: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1025 messages)
*Mar 1 00:00:06.104: status of voice_diag_test from WLC is false*Mar 1 00:00:07.156: STUB Called : crypto_ssl_init*Mar 1 00:00:08.198: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up*Mar 1 00:00:08.244: %SYS-5-RESTART: System restarted --Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)Technical [URL] Copyright (c) 1986-2011 by Cisco Systems, Inc.Compiled Wed 13-Apr-11 12:55 by
[code]....
Recently I have purchased two brand new wap4410n access points.
I have connected my computer directly to one of the access points, and attempted to connect to the Web Configuration utility through my web browser.
I'm using a: 09' MacBook Pro, running Snow Leopard and Safari 5.
I can access the login screen of the access point, although when I enter the default username: admin and password admin, the login screen returns an error: Invalid username and/or password (or something to that effect). The URL changes to: http://192.168.1.245/login.htm&no=3.
I have reset the device by holding in the reset button for thirty seconds, powered down, powered up and re-attempted to login.
I still get the same error as above.
I have attempted to access the Web Configuration utility on both access points, and both access points provide the same error. I have also tried using the username: cisco and password: cisco.
Cisco, when contacted, said both access points must be faulty and I should replace them.
The probability of such an occurrence happening with two devices seems very low, and leads me to think there must be other factors at play. The only constant I can think of is the fact I'm using the same computer to access the devices.
How can i edit on who will have the most percentage of internet?i cant access the username and password.
View 1 Replies View RelatedI am unable to set a password and/or username for guest access.
View 1 Replies View RelatedI did not know the username and password for my DI-524 so I wanted to do a reset...used a paper clip and held the reset button for ten seconds, unplugged it, powered it up, and as per online instructions tried to type in 192.168.0.1 to access the username and password field so that I could enter "admin" and blank password. Here's where my lack of knowledge comes in. I am working off a MacBook with no Ethernet connection, just wifi. Is what I am trying to do even possible? Or does the computer I configure the router with have to be hardwired to the Internet while I do it?
View 1 Replies View RelatedI cannot access the Username and password on my WAG160N - the ones I thought were correct do not accepted, nor are the quoted 'defaults'.I have tried holding down 'reset' for 30 secs; I have tried powercycling the router after and during this; I have tried 'resetting' with the phone and ethernet connections unplugged. This is NOT returning the machine to the default settings - and neither is it 'wiping' the existing settings for my ISP.The amusing thing is - it works perfectly well, but I can't alter my security settings and I can't alter other settings if I change my ISP (as I was intending to do).
View 9 Replies View RelatedI would like to ask some question on WLAN technology, which I using WiSM version 2. And i get requirement that user must be restrict with SSID, so, i found that it can do it on ACS version 4.x via NAR for SSID-based authentication feature. Then, is it possible to do restriction on ACS Version 5.x?
View 4 Replies View RelatedI have reconfigure my Cisco 3825 for ssh after we lost the config sue to a power faliure. I have reconfigure the same way it was configured before and working properly.
when I try to access the router using Putty ssh, I get to the authentication screen but after entering uername and password (enable secrete and line password the same) i get access denied.
Below is the ssh and line configuration on the router. I have seen the pdf that has been recommended here at Netpro and have followed that document but still having problem:
[code]...
Can I use AAA Radius on a ASA 5505 to block outgoing user access by user name in a group?
View 2 Replies View RelatedI am using a network switch to share my broadband between four PCs.Among these PCs, one is for students. Is it possible that I can do the following 2 things from modem whose page can be accessed through 192.168.1.1;
1. Restrict some website like Facebook, Youtube etc
2. Limit download speed of that PC to 100KB/s
I am a restaurant owner and have a wireless network set-up via DLink DSL 2730U router. Now some times I get customers who demand to use the network and they use it for free which I find irritating. I have found one solution of 'Guests/Virtual Point' but I need to limit the time (say 15 minutes) for which they can use the network.
View 1 Replies View RelatedI've my ACS linked with AD to give administration access to few network devices and I've created an access policy to link my AD groups with those network devices and command sets.
Unfortunately I found I can use any user from my AD to login to my devices. Only LOGIN, the authorization definition is restricting the command set for those users.
How can I restrict the LOGIN to an specific AD group?
when im entering ip address of other computer in my remote desktop an error msg is coming "unable to logon you because of account restriction" fire wall and virus protection is off.
View 1 Replies View RelatedWhile I was at school there was a system in place where by you had to enter a user name and password to access the internet. Every student had a data limit like 3GB per month for example. I remember it had something to do with a proxy. I would like to recreate this system on my office LAN as some staff members have been downloading a lot slowing down the (very expensive) Internet connection. Limiting each users data will discourage large downloads.
View 1 Replies View RelatedWe have configured ACS 5.1 for autenticating wireless users with active directory, which is working fine now.But we would like implement that single user should be authenticated through ACS . If any user try to access WLAN from multi system will be notified with multi login access restriction.Can we implement this policy in acs, if possible what are the exact configuration changes we have to implement.
View 1 Replies View RelatedThere are 10, 50 and unlimited users profiles for the ASA 5505, reason for that restriction? Does that mean for example that only 10 users can go through a 10-user 5505?
View 6 Replies View RelatedWe are using ASA 5510 Version 7.2(4) at our organisation. The requirement is we need to give an access to a user with limited access so that he can run only specific commands on configuration mode. We don't have Cisco TACACS server instead of that we are using a microsoft radius server.
View 6 Replies View RelatedI am running the SGE2000 as my l3 core switch with multiple inter-vlans.
have a customer requirement that needs to restrict eg. GUEST-VLAN10 to all other VLANS in the network. Only allowing access to the internet.
It seems on the switch i am able to bind ACL to per port interface. if this is possible on the SGE2000
Router 2811 got 3 Interfaces. One Interface connected to INTERNETProvider, Second Interface connected to Sales_Dept, Third Interface connected to Business_Dept. Internet Bandwidth in Total is 8MB. I need assistance to allocate 6MB total bandwidth to Sales_Dept and 2MB total to Business_Dept Sales_dept has 48port switch 2960, Business_Dept 24 port switch 2960. Gateway for users is the 2811 Router and both are on different subnets
View 3 Replies View RelatedI get that to avoid fragmenting the packets we need to reduce the MTU to 1492, fine, but should the MTU restriction be applied at the virtual-template (server)/dialer (client) or on the physical ethernet interfaces?If I apply it to one or the other, which takes precedence? Should I just apply it to both the virtual/dialer interfaces and the ethernet interfaces?
View 6 Replies View Relatedi have asa 5520 configured as VPN Gateway to terminate remote access vpn , i have question , how can i restrict the access to only 1 range of public source IPs to access my corporate via RA ,is this possible?if so how to configure it?
View 1 Replies View Related