I am a restaurant owner and have a wireless network set-up via DLink DSL 2730U router. Now some times I get customers who demand to use the network and they use it for free which I find irritating. I have found one solution of 'Guests/Virtual Point' but I need to limit the time (say 15 minutes) for which they can use the network.
View 1 RepliesThere are 10, 50 and unlimited users profiles for the ASA 5505, reason for that restriction? Does that mean for example that only 10 users can go through a 10-user 5505?
View 6 Replies View RelatedI run a business and have customers who would like to use my wireless internet. I previously had a completely open network that I would allow them to use, until someone illegally downloaded a movie and got us in trouble. I would like to allow use of the network again, but limit activities like this. Basically, so they could only do basic web browsing, etc.
View 1 Replies View RelatedWe have a customer with ACS 4.2 Appliances who currently uses the Layer 3 web-redirect guest function to authenticate users against AD via ACS and LDAP to the AD, its a mixture of un-managed Windows, Mac & linux clients.
They want to move to an 802.1x solution.
Now MS-CHAPv2 is proably the obvoius choice (maybe it isnt considering Linux and MAC clients ... comments???). However the only option to integrate with AD is LDAP i.e remote agents or an upgrade to 5.x is out of the question.
Our Guest access system seems to be having problems with DHCP. It seems to take a while to deliver an IP address making the client device show the "limited or no connectivity" message, which of course makes the users complain. On one occassion I have seen my own client eventually picking up an address even after the limited connectivity message appeared. On another I saw the debug showing "Dhcp request for autoconfig address", which I suspect is a symptom of the problem.
Our Anchor Controller is the DHCP server and is a 4402 running 7.0.98.0 - I've attached some DHCP packet debug.
We recently implement WLC 5500 Series, I found out guest user once period of that user expired it will not appear at lobbyadmin page where you can see list of users.
Is there any way to see expired guest users and also IP address which assign to guest user?
I have a cisco wlc 2504 is deploying authentication services to guest users toward a portal web customized and configured. I need to install my certificate verisign (certificate.cer) in to cisco wlc because my users don't like the page no trusted (The wlc is showing me ''There is a problem with this website's security certificate'') when they are trying to access to ssid to users guests.
View 2 Replies View RelatedHave a WLC 5508 running 6.x code with LAP's providing wireless for our internal laptops (WPA2 and EAP-TLS). I want to provide guest wireless which goes out a different port on the WLC to a guest firewall/cable modem. However, we want to prevent our internal laptops from being able to use the guest wireless. I have RADIUS (IAS) and LDAP for my AD available. We would prefer not to have use Lobby Ambassador and just have the guests use a simple password or web passthru. Guests may be laptops or smartphones. What options are available? I have tried a test setup using dynamic vlan assignments from RADIUS using the IETF flags, but can't seem to get it to work. Is there a way to identify the SSID is being used at the RADIUS server?
View 13 Replies View RelatedI would like to integrate our intranet web page with Cisco WLC 2500. Is it possible to integrate custom web page with WLC. I know, that I can create custom authentication page, but what about creation of the user?
View 5 Replies View RelatedMy customer has multiple sites, each with a 2504 WLC.A data center with a 5508 in the DMZ acting as Anchor for the remote sites.ACS 5.x and NCS Prime.All guest users will egress to the internet via a Vlan in the DMZ.Authentication is currently web-auth on the Anchor, but will move to NCS once that is fully deployed.
Is it possible to put a printer in each site for Guest WLAN users to use?
We have Cisco WLC 7.0 with private and public accesses. Is it possible to limit guest session time? For example, any visitors’ connection will be disconnected after 1 hour.
View 3 Replies View RelatedI have DIR-615 Cx (bought in Taiwan) Hardware C2 ver. I reflashed with DIR-615 firmware from Singapore to get English interface. I connect to a internet through another router on which I setup D-Link on DMZ with port forwarding. Router works fine, I have internet connection. So the question is: I have small cafe and want to offer customers WiFi connection. I want to setup a time limit and allow them to browse only internet not internal network. (When I connect laptop to D-Link Wifi I can see my NAS on different subnet connected to cable modem/router) And if its possible to limit bandwidth. Can I do it with DIR-615 and how to configure such a setup?
View 1 Replies View RelatedCant we create a guest user login with more than 30 days lifetime? In the lifetime field we can enter maximum 99 but it only allows up to 30
View 5 Replies View Relatedwe plan to implement the SMB Pro AP541 for a guest access solution.is there a lobby ambassador like on the big wireless lan controller?is it possible to sign a guest a time frame - e.g. guest user has only 60 min access to the internetis it possible to enter a lifetime for the guest user - e.g. guest user can only login until 10.10.2010
View 2 Replies View RelatedI have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running Win XP PRo SP3.
View 1 Replies View RelatedI have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running WinXPPRo SP3.
View 4 Replies View RelatedLooking to add time of day restrictions to our Guest WLAN that is currently in its pilot phase.
Is there a way to config time of day access to a WLAN ?
Recently i have setup a WLAN with inside and anchor 5508 controllers. Standard setup. However, one issue I have is I wish to extend the length of time between password changes for users connected in on the guest wlan. At the moment, 30 is max. I dont have an option on the controller to creat accounts for any longer than that. How to I extend it to 90 days or 120 days?
View 1 Replies View RelatedCan i control the on/off time of the entire guest network?Or can use parental control for computers logged onto the guest network?
View 1 Replies View RelatedThis is the first time I am trying my hands on wireless gears. I have 2500 WLC and 1142 AP (which I converted from Standalone to LAP).I have a layer 3 POE switch where i am using port 1 for the WLC which is a trunk port.
Port 2 is for the AP using access vlan 111
Port 3 is trunk port going to a router where i am running dhcp server for the VLANs which are as follow:
VLAN 110 -Corp Wireless (10.1.110.0/24)
VLAN 111 - AP-Mgmt (10.1.111.0/24)
VLAN 999 - Guest (10.1.101.0/24)
I wanted to block the traffic from the Guest VLAN 999 but when i apply the ACL on the Guest Interface created on the WLC, I dont see any pings going across and neither I see any hit counts on the deny statement as if the ACL is never applied.
I am using a network switch to share my broadband between four PCs.Among these PCs, one is for students. Is it possible that I can do the following 2 things from modem whose page can be accessed through 192.168.1.1;
1. Restrict some website like Facebook, Youtube etc
2. Limit download speed of that PC to 100KB/s
I've my ACS linked with AD to give administration access to few network devices and I've created an access policy to link my AD groups with those network devices and command sets.
Unfortunately I found I can use any user from my AD to login to my devices. Only LOGIN, the authorization definition is restricting the command set for those users.
How can I restrict the LOGIN to an specific AD group?
Any problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies View Relatedwhen im entering ip address of other computer in my remote desktop an error msg is coming "unable to logon you because of account restriction" fire wall and virus protection is off.
View 1 Replies View RelatedWe have 4 SSID's established for our staff, students, Guests and Providers. CISCO / ARUBA Managed APs with a centralized CISCO Controller. Can I restrict access by the first letter in the username so that usernames that begin with x will ONLY connect to the Staff SSID if in range and usernames starting with y ONLY connect to the student SSID?
View 1 Replies View RelatedWhile I was at school there was a system in place where by you had to enter a user name and password to access the internet. Every student had a data limit like 3GB per month for example. I remember it had something to do with a proxy. I would like to recreate this system on my office LAN as some staff members have been downloading a lot slowing down the (very expensive) Internet connection. Limiting each users data will discourage large downloads.
View 1 Replies View RelatedWe have configured ACS 5.1 for autenticating wireless users with active directory, which is working fine now.But we would like implement that single user should be authenticated through ACS . If any user try to access WLAN from multi system will be notified with multi login access restriction.Can we implement this policy in acs, if possible what are the exact configuration changes we have to implement.
View 1 Replies View RelatedWe are using ASA 5510 Version 7.2(4) at our organisation. The requirement is we need to give an access to a user with limited access so that he can run only specific commands on configuration mode. We don't have Cisco TACACS server instead of that we are using a microsoft radius server.
View 6 Replies View RelatedI am running the SGE2000 as my l3 core switch with multiple inter-vlans.
have a customer requirement that needs to restrict eg. GUEST-VLAN10 to all other VLANS in the network. Only allowing access to the internet.
It seems on the switch i am able to bind ACL to per port interface. if this is possible on the SGE2000
Router 2811 got 3 Interfaces. One Interface connected to INTERNETProvider, Second Interface connected to Sales_Dept, Third Interface connected to Business_Dept. Internet Bandwidth in Total is 8MB. I need assistance to allocate 6MB total bandwidth to Sales_Dept and 2MB total to Business_Dept Sales_dept has 48port switch 2960, Business_Dept 24 port switch 2960. Gateway for users is the 2811 Router and both are on different subnets
View 3 Replies View RelatedI get that to avoid fragmenting the packets we need to reduce the MTU to 1492, fine, but should the MTU restriction be applied at the virtual-template (server)/dialer (client) or on the physical ethernet interfaces?If I apply it to one or the other, which takes precedence? Should I just apply it to both the virtual/dialer interfaces and the ethernet interfaces?
View 6 Replies View RelatedMy Wireless-N Home Router WRT120N with version 1.0.07 seems to have a problem blocking Sites through scheduling with Access Restriction "Allow" ...I notice that... when I enable access restriction, with policy and some range of computers connecting to my router , and set it to "allow" from "monday - friday" from "8am-6pm" .. with a purpose of blocking some social networking sites, example facebook, It works perfectly fine. But when the "scheduled" time comes ( before 8am and after 6pm ).. I cannot access the internet.. router is working, it detects my modem.. but no internet connection. It always happen before and after the "scheduled time" before the configured access restriction takes over. I have to disable the Access Restriction to continue our internet access.
View 4 Replies View Relatedtarget 192.168.0.21following are rules of access restriction on WRT54G1.rule A- 07:00am~10:00am,internet access allowed, keyword blocked such as Facebook,mail.2.rule B- 10:05am~10:00am,internet access allowed, no keyword blocked.but 192.168.0.21 fails to access internet after rule A expired.
View 1 Replies View Related