Internet Connection On XP Dual Boot
Jan 19, 2013
I am running Windows XP and Linux Ubuntu on dual boot.When I open into XP I cannot establish an ADSL internet connection, but can by wireless.If I open into Ubuntu I can establish both ADSL and Wireless internet.In Windows I have checked my Realtek Card in Device Manager - says working O.K.. When I try to open internet by ADSL the message is " trying to assign IP address " then limited or no connectivity" - if I try "Repair" message cannot establish IP address.Clearly something is blocking my connection.
View 17 Replies
ADVERTISEMENT
Dec 2, 2012
I have build a new pc this week. All was fine offline. After connecting to the Internet initially everything loads quickly however sometimes after turning on my pc or restarting it the Internet just refuses to load. Pages take forever then I get a message unable to connect however the connection is still active and all my other devices work ipad etc. after a few times restarting or leaving it for a while all is fine.
View 1 Replies
View Related
Jan 26, 2011
My setup was as follows:
Computer 1 - Win7 ip address 192.168.1.2
Computer 2 - Ubuntu 10.10 ip address192.168.1.3
Had samba working Ok Decided to check out Fedora 14 so set it up as dual boot on Computer 2 and installed samba.
Computer 1 - Win7 ip address 192.168.1.2
Computer 2 - Dual boot Ubuntu 10.10/Fedora 14 ip address 192.168.1.3
When Ubuntu is running, Win 7 sees shares for Ubuntu. If Fedora is running win 7 cannot connect to any shares stating a bad file path. From my understanding as both linux os'es are on the same computer, using the same connection, the ip address for both would be the same and that�s probably were Win7 must have problems. From what I've read on the net it seems changing the netbios name or computer name would not work as Win7 would only use these to resolve the ip address which in this case would be the same.(Could be wrong).So essentially is there a way for Win7 to recognise which linux os was running on Computer 2 and display the shares accordingly.
View 6 Replies
View Related
May 20, 2012
I have an HP-MINI with an atom processor 1.6ghz and dual core according to device manager. It has 1 gb ram and no other issues. I can boot into Ubuntu and have everything work fine. It goes on line with no prodding on WAP after I enter the password as usual.
When I attempt to do this in winXP on the same exact computer, it comes up with the no connectivity issue. I have run ipconfig and here is the result: (btw I am sending this info from another computer)
Windows IP Configuration
Host Name . . . . . . . . . . . . : KEN_HP_MINI
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
[code]...
After I ran this see that Netbios over TcpIp was disabled. I am sure it is supposed to run in some kind of automatic mode or something as I recall.
View 8 Replies
View Related
Jun 3, 2012
Currently have two laptops: one is a MacBook using OS X, the other a Gateway PC running Vista Home Edition. A Dell Inspiron 17R notebook running Windows 7 Home Premium is in process of delivery. Current laptops linked on a home Wi-Fi network with AirPort Express router. Anticipated use of new Dell notebook requires its direct connection to Internet outside of current network configuration. Is it possible to have both accesses available in my setup utilizing my one cable high speed service connection? If so, what are the steps needed to accomplish the required setup?
View 1 Replies
View Related
Jan 23, 2013
Region : Malaysia
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 121106
ISP : unifi
i just bought this router and upgraded the firmware. but i cant seem to get Internet connection up and running. it says connected but its not. tried both 121106 and 121226 firmware, still the same. when i checked the connection it says DNS server not responding.
View 7 Replies
View Related
Apr 15, 2013
Region : Hongkong
Model : TL-WDR4300
Hardware Version : V1
During long, heavy download streams (such as BT, video streaming) the router WDR4300 would still lock up the internet (WAN) connection for that client. I could still go to the admin web page on that client but no internet activity would occur until either rebooting the router.
View 8 Replies
View Related
Apr 11, 2011
My PC Info: Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft� Windows Vista� Home Premium , Service Pack 1, 32 bit
Processor: Intel(R) Core(TM)2 Duo CPU T5850 @ 2.16GHz, x64 Family 6 Model 15 Stepping 13
Processor Count: 2
RAM: 3069 Mb
Graphics Card: ATI Mobility Radeon HD 3450 , 256 Mb
Hard Drives: C: Total - 305242 MB, Free - 252510 MB;
Motherboard: Dell Inc., 0F700C, , .8QQVVG1.CN4864388L1948.
Antivirus: Norton Security Suite, Disabled
So I am having issues connecting to the internet. I can connect during safe mode but not on normal boot. I ran a diagnostic and it said that the IP Gateway failed. I read a previous post and did the command promp "ipconfig/all" and this is what it said:
Microsoft Windows [Version 6.0.6001]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersEbony>ipconfig/all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Ebony-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid[code].....
I have norton, and have recently run Malwarbytes, Microsoft Malicious Removal Tool, and Dell PC Tune Up
View 6 Replies
View Related
Nov 10, 2011
everytime I turn on my PC it doesn't see the modem or router and won't connect to internet. I have to turn on the PC, unplug the modem and router and replug them in before it sees the internet.Any other way of doing it doesn't work. (I leave modem router on 24/7, PC is the one in sig, running Win &. Modem is an older Motorala surfboard, wireless is ZyXEL XtremeMIMO X-550 Router.
View 2 Replies
View Related
Mar 23, 2011
I would like to configure my Cisco 881 enabling Dual Wan (load balancing and failover). First link: HTTP, FTP, SMTP,...Second link: DATA inter-site (VPN), VoIP,Does the configuration seem OK?What does the command line "track 1 rtr 1 reachability delay down 1 up 1" mean?To send the different flow on one or the other port, do i have to configure it on the ACL1 and ACL2 ?
View 9 Replies
View Related
Mar 30, 2012
I created three different Remote VPN connections with three different networks . i can make them one but for some reasons i don't mix all.and iam using Cisco asa 5505 with Shrew Soft VPN software , so my problem is,- i connected Shrew soft remote vpn , if i try to connected another remote vpn connection this will not accept the second connection, any remote vpn connection software that accepts more than one connection
View 1 Replies
View Related
May 24, 2011
I have CSS CSS11501 which is working fine in single arm deployment. Now I want to have redudency so that in case the switch 1 where CSS is currenlty connected is down.I can reach the CSS through the second switch 2.Both the switch are trunk with each other and CSS has one port connected with Switch 2.
View 2 Replies
View Related
Nov 2, 2011
We have an ASA 5510 with ~100 vpn lan2lan. Now we need to migrate to a new ISP, so we have connected a new asa interface to the internet. Default gw is still on old connection. We are trying to migrate vpn lan2lan using static routes, pointing ip of remote vpn gateway to new isp gateway. VPNs going up, but when they try to send traffic, I can see Rx counter growing up, but Tx remains 0.. I've tried with different vpn (old and completely new), and problem remains.
View 1 Replies
View Related
Feb 6, 2013
Region : UnitedKingdom
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : v1
ISP : plusnet
I have a WR2543ND router and everyday it drops the wireless connection . all the lights on the router stay on and im still connected to the router but it looses the internet connection . the windows trouble shooter says that it cannot connect to the dns server , I have to reset the router and my computer to get it working again . I Have updated the firmware but still the same
View 10 Replies
View Related
Dec 10, 2012
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Comcast
The 5 ghz connects fine for multiple machines however machines on 2.4 simultaneously lose their connection to the internet, sometimes saying it is still connected to the internet when it is not and sometimes losing connection with the router entirely. The 5ghz still works when this happens.
View 14 Replies
View Related
May 22, 2012
how can I setup that the backup connection will start but after 30s of icmp timeout the default gateway (tracket object - 192.168.1.1)
My configuration:
sla monitor 123
type echo protocol ipIcmpEcho 192.168.1.1 interface outside
num-packets 3
frequency 10
sla monitor schedule 123 life forever start-time now
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 track 1
route backup 0.0.0.0 0.0.0.0 192.168.2.1 254
track 1 rtr 123 reachability
View 2 Replies
View Related
Nov 9, 2012
Region : Canada
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.17 Build 120509 Rel.33890n
ISP : shaw
my lenovo 510 running windows 7 has the wirelss router listed in the wireless netowrk connection list but cannot connect to the router. it can connect to other routers without any problem.
View 4 Replies
View Related
Jan 9, 2013
Region : Iraq
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : LATEST VERSION UPGRADED
ISP : Newroz Telecom
I purchased TP-link, i want to connect with ADSL modem, i connected successfully through pppoe it shows every ip through lan and wan connected, but it doesn't receive packets / bytes from internet, this is the first problem.the second problem is: i use UPS with TP-Link sometimes my electric power is low just with this tp-link it has problem and refreshing the tp-link
View 1 Replies
View Related
Feb 19, 2012
I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and will peer with ISP via BGP for Internet connection The 2 Nexus in the aggregation layer will be configured as layer 2 device and have FEX and switches connected to them.What I am ensure of is how the vpc and port-channel configuration should look like between the 4 nexus. What I was thinking is to run vpc between the 2 Nexus in the aggregation layer and between the 2 Nexus in the core layer. Than I was thinking of connecting each Nexus in the aggragtion layer to both Nexus in the core layer using port-channel and vice-versa.
View 3 Replies
View Related
Dec 17, 2012
how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
View 2 Replies
View Related
Mar 29, 2012
I wanted to ask a question about the diagram I have included. We are bringing up 2 MPLS WAN connections and would like some specifics on the best design. We are using BGP to the providers. From there we have big questions. We can run BGP internal and are licensed to do so on the N5K's. The N5Ks are currently using HSRP for inside LAN clients as default gateway. We want to load balance and provide redundant routes using a dynamic approach. Should we use BGP internal utilizing the connections between the routers? Should we use HSRP on the routers? How best to get the routes to the N5K and should we be considering this?
View 5 Replies
View Related
Jan 18, 2012
I am using the E2500 v1.0 on TWC network (road runner) wit a VISTA upgraded to Windows 7 laptop.After few months the router is starting losing connection. I tried connecting my laptop directly to the twc modem and the connection is fine, while if I connect to the E2500 v1.0, through wired or wireless connections, I see that the connection is going back and forth.I tried resetting the modem and the router, upgrading the wireless router firmware, but nothing worked.
View 1 Replies
View Related
Feb 2, 2013
Region : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 120820
ISP : German university ISP
I have a big problem with several TP-Link routers (WDR3600, WR1043ND, WR741ND), always with the latest firmware and also with older ones. After a day or so, my internet & network connection will drop all of a sudden and all the routers need a reboot. There is no indication on what provoces these lock-ups. The routers can handle heavy traffic (bittorrent /w 100s of connections) but will stop working when browsing casually. The web-GUI will become unreachable. No pings to the outside are possible anymore, not even to direct IPs (8.8.8.8 for example). No pings to devices in the same network are possible either.
View 7 Replies
View Related
Aug 4, 2012
My wifes Dell D600n with with Intel 2200BG wireless G card was Extremely difficult to get access to internet at first @ 54Mbps, but achieved it after 3 weeks of trying, after I had replaced motherboard, to fix battery charging issue.
The current problem, that i cannot seem to surmount is: I replaced the wireless card with a newer Broadcom BCM43222, Dual band N wireless card, that should be capable of connecting at almost 6 times the speed of the older G card. Unfortunately, the new card seems unable to connect at all.
ADDITIONAL INFORMATION: The wireless switch via keyboard Fn & F2, has been on the entire time. I've tried a couple of different drivers, to no avail. Ive uninstalled/ reinstalled both the card and drivers several times, still no connection. The device manager reports the card is off, at all times, and i cannot find any way to alter this, but, despite the fact that this sounds like it could definitely cause no connection, this is unlikely to be the reason, because it has reported that the wireless card is off at all times since the new Motherboard was installed, and the Wireless G card worked perfectly for the past 2 months, and still does, while the device manager was all the while reporting it was off.
Also the wired broadband connection, via cat 5, had never worked after changing MOBO, Nor did the Dial up modem, til both modem and Ethernet came to life, last night after reinstalling drivers for both the modem and Ethernet. unfortunately doing the same thing for wireless had no effect. All this time the Intel wireless G card has, and still does work perfectly every time i remove the Broadcom Wireless N card and plug the G card back in. Until lastnight, The device manager reported the wireless card had no driver installed. now it recognizes the driver is installed but still cannot connect wirelessly One wireless card driver I tried was called: BROADCOM_ABGN_DD-WRT.zip. I lost track of the name of the other driver that i've been trying. Someone on another forum said after installing BROADCOM_ABGN... That one must go to device manager advanced properties and select US from choices of US, Japan, or Germany, To get this driver to work. I've tried this too. Again, No improvement.
Ive built my own computers for the past 30 years, and repair them all the time, for hardware problems, but I fear software is not my forte. My son, who is better at software. Usually, together, we can solve any mechanical electronic or software malfunction, but we're both stumped by this one. Admittedly, we all sometimes overlook a simple solution while seeking a very difficult one. Whenever I face a difficult malfunction like this, I think of when as a 5 year old I was privileged to accompany my Engineer big brother to a local Airport to repair what i would later learn was a Automatic Direction Finder System, needed before flight. As I sat beside my on the tarmac, watching him sweat bullets trying to effect a quick fix, I noticed something that looked out of place to me, and started chanting his name, Ronnie, Ronnie, Ronnie... ad infinitum, as kids are like to do, til in desperation he finally dropped his screwdriver withwhich he aws about to dismantle the entire mechanism, and fairly yelled what?, to which I asked timidly, Ronnie are all those lightbulb things (electron tubes) supposed to be lit. he said of course!, and continued working, ignoring me for another hour. Finally when he stopped to scratch his head, I said "If they're all supposed to be lit why is one of them not lit? he insisted they all were, but was adamant that they weren't. when he asked which one, and i pointed to it. He tested it verifying the filament was, indeed, open, and demanded to know why id watched for 4 hours and hadn't said that before.
View 2 Replies
View Related
Feb 21, 2013
I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
View 2 Replies
View Related
Aug 6, 2012
I have a Netgear N600 WNDR3700v1 Dual Band Gigabit router and am having a problem with the wired connection with my PC. Everything wireless in the house works fine. In fact, I also have a Direct TV box hooked up for on demand and a sling box hooked up (both wired) and they work find. It's just my PC that is having issues. If I bypass the router and hook straight into the modem, it runs fine also so I have something going on between the router and this PC. I updated the NIC driver and this did not work. Before the update in the device manager, it said it was a NIVIDA nForce Network Controller (if I remember right) and now it says NIVIDA nForce 10/100 Mpbs Ethernet. It was suggested that I change my speed and duplex to match the router after I update but I am unsure what to change it to.
View 11 Replies
View Related
Nov 21, 2012
Region : Singapore
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : starhub
1) Always auto disconnect (limited access),
2) My smart phone Motorola MB860 (android 4.0.4) Can connect but can access internet.
3)Always connect to 2.4GHz ,never see connect to 5GHz.
4)Wireless connection 15-20 Max Mbps Only ,LAN can up to 50 Mbps .
View 9 Replies
View Related
Apr 26, 2013
Region : Hongkong
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 3.14.3 Build 130320 Rel.39025n
ISP : PCCW Netvigator
I have upgraded to the latest firmware which solved lots of problems regarding unstable wifi connection as well as BitTorrent / P2P transfers.But I also observed that when my BT is on (Transmission for Mac) at around 50KB/s upload and download, my network latency hikes up from some 30ms to 500ms which affects a lot on web browsing or other apps requiring Internet.My BitTorrent app is showing I am merely making some 20 peers connection so I am not convinced that is an ISP problem but it's more about the router.
View 1 Replies
View Related
Aug 11, 2011
I got Windows 7 Enterprise-32 bit which cannot run some old programs,games,etc.So i decided to install Windows XP professional, but there's a huge problem: The internet does not work when i change to XP, but when i change back to win 7 it works again. Should i call my internet provider?Unplugging,creating,disabling the internet does not work,also it's not the problem with firewall.
View 2 Replies
View Related
Jan 22, 2013
Region : Others
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : UPC Hungary Ltd.
I can't able to recognize a system - all wifi clients lose connection. When this happens, the ping answer time rech the ~2000 times, then totally lose the connection, the SSID is dissapear - checking with my phone (android - wifi analyzer) and TL-WN822N USB wifi adapter (with the inSSIDer application). Meanwhile the cable clients and the WAN connections works fine, didn't experience anything.If I restart the wifi service with the hardware on/off button, it runs well for some time.This problem appeared when I used the two older official firmware too.
I tried the auto-chanel function width auto channel width, tried to manually set up one of the less interfered channels with both 20MHz and 40MHz channel width, but none of them bring the solution.The intresting thing is, if I change the router with an old D-Link DI-604, the signal is weak, but the wifi connection is stable, with the same TL-WN822N adapter.I tried to guarantee the router, but after two weeks, my reseller said, it looks ok, they - at the TP-Link service - didn't find anything.
View 7 Replies
View Related
Oct 8, 2012
Got a situation where Location_A got TWO ISP and Location_B got One ISP.Using ISP 1 link Location_A establishes IPSEC Tunnel with Location_B .How do I establish redundancy from Location_A point of view, if ISP1 is down then ISP2 should establish IPSEC tunnel with Location_B.At Location_A both ISP links terminates on the cisco PIX-525 and all (VPN) crypto configuration is on PIX 525 running version PIX Version 7.2(4)7At Location_B VPN is terminated on a PIX Version 6.3(3).
View 2 Replies
View Related
Mar 29, 2013
Region : UnitedStates
Model : TL-WDR4900
Hardware Version : Not Clear
Firmware Version :
ISP : Comcast
The internet connection works really well on the 2.4GHz connection and when wired. But when Im connected through the 5GHz network, I get no internet.
View 2 Replies
View Related
May 31, 2012
I have a single 7204XVR Internet router with two active Internet connections. One connection is ISP1 (Primary) and 50MB, and one connection is ISP2 (Secondary) is 4.5MB. We have customers from all over the Midwest and East Coast. The customers that are on the East Coast are coming in through the slower ISP2 connection and are complaining of slowness of our applications. However, the customers in the Midwest are coming in from ISP1 connection and are completely satisfied. Unfortunately, I am not a BGP expert, and I am not sure how, if possible, to FORCE ALL customers to use the primary ISP1 connection in reaching our sites/applications.
View 6 Replies
View Related
