Cisco WAN :: 7204XVR - Dual Home Internet Router With BGP
May 31, 2012
I have a single 7204XVR Internet router with two active Internet connections. One connection is ISP1 (Primary) and 50MB, and one connection is ISP2 (Secondary) is 4.5MB. We have customers from all over the Midwest and East Coast. The customers that are on the East Coast are coming in through the slower ISP2 connection and are complaining of slowness of our applications. However, the customers in the Midwest are coming in from ISP1 connection and are completely satisfied. Unfortunately, I am not a BGP expert, and I am not sure how, if possible, to FORCE ALL customers to use the primary ISP1 connection in reaching our sites/applications.
View 6 Replies
ADVERTISEMENT
Nov 20, 2011
My home desk top is set up with D-Link Xtreme N Dual Band Router. I have no problems accessing the internet on my desk top computer. I am trying to access my home wireless network through my HP laptop computer. The wireless network status is Limited or no Connectivity. I've tried the "repair" button with no resolution. The wireless connection is set to automatic.
View 1 Replies
View Related
Mar 10, 2013
I have a router with 2 service providers connectivity with different ASN and running with BGP.I've announce few IP-prefix by ISP-A and Few Prefix by ISP-B.Both are working well with redundancy.But,Problem is here, that the all uplink bandwidth goes through ISP-A link.I want to make it that, ISP-A routed ip-Prefix's upload data will go through ISP-A & ISP-B IP-Prefix's Upload data will go through ISP-B Link.
View 9 Replies
View Related
Dec 7, 2012
I currently have a NetGear WNR3500L running Tomato acting as an access point. Unfortunately, I think it's crapping out on me... Currently, there are two WiFi security cameras streaming through it to a surveillance server 24/7, and even though it is in a central location in my condo, I get shit signal ~25 feet away (and that's after cranking up the wifi radio to 60mw).
802.11n is a must, and dual SSID's would be nice too... dual band would be totally awesome but not that necessary (I still have some legacy hardware running on G...).
View 10 Replies
View Related
Aug 22, 2011
I have a computer in my garage that is connected to my Linksys router in the house via Cat 6 Cable. The computer in the garage has dual NIC cards installed and working fine. I am trying to get the Camera to feed back to the router from the second NIC card in the garage computer.The first NIC is communicating fine with the router.
Linksys Settings:
192.168.1.1
255.255.255.0
NIC 1:
192.168.1.145 (static)
255.255.255.0
192.168.1.1
[code]....
After messing around with many different thoughts and tries, I have successfully contacted 192.168.1.120 (the camera) from garage Computer While camera is connected to NIC 2.Camera wants a crossover cable to function properly and won't accept patch cable, I have tried with new cables...no change it needs crossover cable when connected straight to the NICs.
Camera:
192.168.1.120
255.255.255.0
192.168.1.1
Now the problem is I cannot view or access the Camera from my main Computer inside the house Like I need to....
View 2 Replies
View Related
Dec 19, 2011
I am currently looking to upgrade and extend my home network with preference to dual band and gigabit functionality. My problem is choosing the correct hardware.I want dual band to separate the network for the kids (a PC, laptop, Xbox 360 and phones all wireless) and set up parental controls and maintain connection speeds etc. For my needs I need the network to be connected to my Onkyo AV Amp (for internet radio and music streaming only), Blu-ray Player, Sky HD satellite box (all wired) and a PS3 (pref wired) and a few wireless devices all N capable. Apart from the obvious gaming capability I would like to be able to stream HD video to the PS3, PC (wired) and laptops via a USB HDD connected for now on an access point or modem router to save on the cost of having separate networked devices.
I currently have ADSL so I was looking to get a dual band gigabit modem router to serve the kids wireless hardware whilst my current hardware is on another floor and is connected with a wire from the existing modem but I have to keep swapping it from PS3 to amp etc.In short I am hoping to have a gigabit, dual band ADSL modem router and connect to a gigabit access point (with dual band if possible) via the cable I have sent to the other floor to wire up the 4 devices. I've currently been looking at Netgear and Buffalo solutions as I've had problems with Linksys and Belkin routers in the past. Would this be possible with just 2 devices (modem router and access point) whilst maintaining decent speeds and if so can someone shed some light as to what I should get.
View 1 Replies
View Related
Jan 12, 2011
I'm building my own home server based on Ubuntu with 4 drives in RAID 10. Its primary purpose will be NAS and backup.Would I be making a terrible mistake by building a NAS Server with a single Gigabit NIC?
I know the absolute max I can get out of a single Gigabit port is 125MB/s, and I want this NAS to be able to handle up to 6 computers accessing files simultaneously, with up to two of them streaming video.
With Ubuntu NIC-bonding and the performance of RAID 10, I can theoretically double my throughput and achieve 250MB/s (ok, not really, but it would be faster). The drives have an average read throughput of 83.87MB/s according to Tom's Hardware.
The unit itself will be based on the Chenbro ES34069-BK-180 case. With my current hardware choices, it'll have this motherboard with a Core i3 CPU and 8GB of RAM. Overkill, I know, but this server will be doing other things as well (like transcoding video).Unfortunately, the only Mini-ITX boards I can find with dual-gigabit and 6 SATA ports are Intel Atom-based, and I need more processing power than an Atom has to offer.
I would love to find a board with 6 SATA ports and two Gigabit LAN ports that supports a Core i3 CPU. So far, my search has come up empty. Thus, my dilemma.Should I hold out for such a board, go with an Atom-based solution, or stick with my current single-gigabit configuration?
I know there are consumer NAS units with just one gigabit interface (probably most of them), but I think I will demand a lot more from my server than the average home user.
View 1 Replies
View Related
Dec 27, 2010
I am simply trying to configure fail over configuration in my 1812 router. I have done some configuration on my router but my configuration is not working as i want. My router does not goes to secondary route until i unplug the primary interface cable on my router. when i unplug the primary cable it goes to secondary route and then i plug back primary cable the router come back to primary link.so my configuration is working when my primary gateway down but it is not working when internet goes down from isp end. i have attached my running configuration.
View 6 Replies
View Related
Dec 16, 2011
How can I use the dual LAN of my PC to share internet with my notebook? The PC is at school where it uses a static IP and I would like to avoid buying a wireless router for this purpose.
View 3 Replies
View Related
May 20, 2007
Having a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies
View Related
Jan 17, 2013
Can I put more than one N300 Dual-Band Wi-Fi Range Extender on my home network?
View 4 Replies
View Related
Feb 7, 2011
The internet at my parents house has recently gone on the fritz..the wireless router is a N600 Wireless Dual Band Router WNDR3400..The computers of the house are able to connect to it..But it does not allow internet connections..The 3 computers are an HP Laptop running windows 7.a Dell Dimension E521 Running windows 7 & and an older HP Walmart special running XP.They can connect to outside systems and through a wired connection to the Modem from Cable vision. They replaced the wireless router and the problem continues.Internet is capable by plugging directly into the Cable vision router,unfortunately do not have the cables to try through the Netgear router to test that out..
View 3 Replies
View Related
Oct 3, 2011
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies
View Related
Jan 17, 2011
I have been having problems forever connecting to internet at my apartment. My roommate has a Belkin router, and him and my other roommate have no problems connecting. I used to be able to get on it fine, however now I either get "connection unsuccessful" or "unidentified...(Belkin.3BC3) - Limited Connectivity" when I try to connect. Our landlord provides the internet, and we have the base router(not wireless) in our basement. But even when plugging into the wall with a ethernet chord I get local only. This is the only place I have any internet problems, anywhere else I can connect just fine.
View 2 Replies
View Related
Mar 18, 2012
Recently we ordered a new Modem from Centurylink to replace an old one we have. (which ironically the old one's wireless is way better) Both modems work perfectly fine, and I've tried the same things with both to figure this out. I ran an ethernet to my gaming room, which is about 150 feet. When I connect my computer directly into the modem, my computer works fine. Initially, the PS3 worked, but when I switched back to the computer with the single Ethernet cable, I was getting an IP error. Every since then, the PS3 will not connect through Ethernet. (Wireless works, but its so far away the signal is weak)
So, I dug up my router, Linksys WRT54GL, plugged it into the ethernet that came from the Modem, (did all the steps in order multiple times), and no internet through wifi or ethernet on it. The lights and everything say there is ethernet and the WIFI/Ethernet are working, but there is no internet. All the wires are confirmed fine. I've tested them on other devices plugged directly into the modem. I tried the PS3 at the modem with 3 Ethernet cords as a test, It says there is an IP Address timeout error. Regardless of what I do, the PS3 won't connect via Ethernet. And without internet working on the Linksys router, Im getting about 15-25% signal from the Modem. (which is also wireless, if that has anything to do with the issue)
I need the router to do at the very least, WIFI. I really want Ethernet though so I don't lose much speed. (We are maxed out here at 1.5mb connection from Centurylink)
When it comes to computers, I'm advanced with them. When it comes to networking, I'm okay. I understand basic things, like accessing the router or modem through the browser. I can do the whole setup for WIFI. But when it comes to how the IP address, Static IP, etc., goes, im confused by them. So forgive me if I sound ignorant. I've looked for over a week on sites, and nothing is working. The router may be broken, im not sure. I bought it a few years ago and then didn't need it till recently. So its been sitting in a box.
All I know is, I have an ethernet from the modem to this room, the PS3 refuses to get an IP, and if I do it too much the PC gets an IP conflict. If I plug the Ethernet into the internet part of the router and do wireless or Ethernet, there is no internet coming out.
View 1 Replies
View Related
Jun 19, 2011
Currently I'm living in a dorm. The house has wireless network. But WEP encryption is used to secure it. I know this method is not safe. Also since there are many people are living in the house i don't want my computers be connected to this network.What i want to do is to setup my own network. I bought a NetGear DGND3300 router. I setup a WPA2 protected wireless network. I can connect all my devices to this network but naturally this way i have no Internet access.Is there a way to use Internet access of the house's router but still keep my local traffic not seen by anybody else
View 2 Replies
View Related
Nov 24, 2011
Orange sent me a replacement Netgear DNG1000 and from the moment I had it there was issues, if N mode was enabled and I had to set it to B/G only for it to have a stable connection, not a problem as I only use it for the internet. The range on it was roughly the same as the livebox. For a few weeks it worked fine until recently it started to go insane, on the main computer the wifi works most of the time with 80%-95% signal strength, and then every now and then it will suddenly lose communication with the router but act as if it was connected for 5-10 minutes, signal strength is still at about 90% yet I can't access the router or the internet. Wifi works fine at full speed on the stairs, drops to a few bytes per second on the landing and then increases back up to full speed in the room next to it. In the one bedroom the wifi works up until the door where it instantly drops from full speed to a few bytes a second. This drop off point is only a few cms, as in full speed at one place, move it back a few cm and it slows down loads, but I still get 4-5 bars on windows and -50 RSSI on inSSIDer, about 94% strength and a link quality which tends to fluctuate. What could be causing this, specifically the weird instant deadzones and randomly not responding.
View 1 Replies
View Related
Apr 15, 2013
Region : Hongkong
Model : TL-WDR4300
Hardware Version : V1
During long, heavy download streams (such as BT, video streaming) the router WDR4300 would still lock up the internet (WAN) connection for that client. I could still go to the admin web page on that client but no internet activity would occur until either rebooting the router.
View 8 Replies
View Related
Jan 31, 2013
I am experiencing problems trying to access my routers HTTP-type configuration. I have a Billion 400G router. The address to access the router was always http://10.0.0.2 and that has always worked. A dialog box would appear asking for a username and password. Now it doesn't even reach that screen. It says that the connection timed out. I've tried Firefox/Chrome/IE10. To no avail. My system: Windows 8 build 9500. Also something weird. When I type in this Microsoft thing comes up with IIS 8.
View 2 Replies
View Related
Jul 16, 2012
I'm having trouble connecting my 02 dongle to the internet using my router. My router is a TP-LINK MR3420 and my 02 modem device is E1752. I checked to see if the modem is compatible and it says it is. I went through the configuration that was given to me with the router and I tried using you tube but nothing. Do i need to get a static I.P address off my Internet provider? If I plug my 02 usb dongle directly into my computer it works perfectly and I got the router to work using a ethernet cable and plugging it into the WAN port at the back of the router but I would prefer to let it connect through the 3g port. I get a connection at 40% and 100 bytes are sent and some are received but the connection drops. Is it a problem with the connection? I will upload a image.
View 3 Replies
View Related
Mar 19, 2012
I have 24 port switch which is already connected to internet through static IP. Now I want to use a router as a wireless device to use internet. How do I connect router to switch?
View 3 Replies
View Related
Jan 30, 2013
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled) 2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the samesubnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it
View 4 Replies
View Related
Mar 23, 2012
I have 2 linksys routers installed on my home network. The primary router is a linksys WRT360n and is stationed inside the main home, while the 2nd is a linksys WRT160N located in my office. I've connected them via the lan to lan configuration and have disabled DHCP server on the 2nd. I can access the 2nd router via my primary PC but am unable to access the internet or see the primary from the PC connected to the 2nd router.
View 3 Replies
View Related
Feb 21, 2011
A while ago internet access was slowed right down for an hour or so. I have a phone line that comes into the house and then into gateway (10.0.0.2) then ethernet from that to linksys wifi router (192.168.1.1). So I did the following ping and repeated what you see below a few times to see that these results were broadly consistent, which was the case. One other person is connected to linksys via ethernet cord and they might have been on at the time. Questions are.... are these results consistent with contention caused by other user on the linksys? and why can I ping gateway but not the router? That makes no sense to me! I am not annoyed with the other person if he is hogging the network...I like him. I just wonder whats going on. When the internet works results from pinging are all as one would expect
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsNASA>ping 192.168.1.1
[Code].....
View 4 Replies
View Related
Sep 19, 2011
I have cable internet with a speed plan in the 10-15 mbps range. I have a wireless Belkin g router that is several years old. Connected to the router I have my cable modem as well as my PS3. I connect wirelessly from my PC to the internet, as my PC is in the other room (more on that later). When I'm streaming movies via WiFi to my TV, the connection is highly unstable. Some days, I will not experience any stuttering (or very minor stuttering), whereas other times the stuttering is almost unbearable. Last night, I had trouble streaming a DVD quality movie whenever it went above 2 mbps total bitrate. Other times, I can stream HD movies without much stuttering (except for very action packed scenes).Interestingly, I stream Netflix movies over my PS3 via a *wired* connection. Last night, I conducted a speed test on my PS3. First, I had the PS3 plugged into the wireless router. I achieved speeds around 2 - 4 mbps on average. I then plugged my PS3 directly into my modem and achieved speeds around 10 mbps! The boost was instantaneous. I should note that on my PC, I speed test regularly over the WiFi and achieve around 4-6 mbps on average (only once did I achieve 11 mbps).
View 4 Replies
View Related
Nov 24, 2012
I would like to wirelessly connect my printer through the new router without internet. The setup CD won't allow me to install without an internet connection.
View 2 Replies
View Related
Dec 20, 2012
I am trying to setup a remote PC over a wireless access Point/Bridge to our FIOS router. Pic of setup is shown below. Everything is connected, there are no errors or security warnings shown in the ActionTec MI424 router. The RemotePC IP shows up as an Active Ethernet client in the Router config app. Moreover, I can run the connectivity test from the router app to the RemotePC and it passes that, and I can PING from the RemotePC to the Router. Yet I cannot reach the Internet from a Browser on the RemotePC (192.168.1.75). I am using (2) DLINK DAP-1522 Access Point/Bridge units and they have worked as expected. I set the Router log to list any blocked IP traffic as well, and it does not show anything being blocked from the RemotePC (192.168.1.75). So why can't I reach the Internet from the RemotePC? Seems like a gateway problem or I need to make some config changes in the Router.
View 2 Replies
View Related
Aug 3, 2012
I've been having this issue for quite some time on my Windows 7 SP3 x64 machine. It's a desktop, connected via ethernet to a TP-Link WR740N router, that also provides wireless coverage. My ISP is a local one (the country is Latvia), and it offers a decent 100 MBps up/down optical fiber internet service. Now for the problem - there is only one home network on my computer, that seems to work, and that is 'Network 2'. Whenever I have to reboot the router for whatever reason, it attempts to reconnect, but sometimes reconnects to a 'Network 3' and once even to a 'Network 4' and 'Network 5'. None of these other networks have internet access. I tried to run the diagnostics tool on the issue, and usually it told me that there's a problem with the default gateway. Additionally, twice I've had the issue of the computer completely freezing when connected to one of the Internet-less networks (eg 'Network 3'), and trying to disable the network adapter, forcing a restart that consequently caused a fail boot - from there on I had to use System Restore to actually get my PC to function.
The way I've been fixing it, apart from random rebooting, reconnecting, and hoping for the best (that it decides it wants 'Network 2'), is by putting in the Resource Mini CD that came with my router, and running the Wizard for the WR740N router. It has 4 steps, the 2nd of which is 'Installing the router' (configuring the network adapter), at which point, my internet starts to work (always connects to 'Network 2'). If, I however, decide to continue this process to the step 'Configure router', and attempt to set up my wireless connection, it will begin to reset itself, and once again connect to 'Network 3', leaving me without internet access.
View 4 Replies
View Related
Dec 25, 2011
Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 2 Replies
View Related
May 3, 2012
So I have a Netgear N600 WNDR3700 wireless router setup at home, and it works great for wireless, but when I plug in my desktop with CAT6 Ethernet cable to the router (didn't bother putting a wifi card in my desktop) for some reason it won't connect to the internet. I know the cable works because I've used it in the past, but for some reason I can't get it to work with my Netgear router.
View 7 Replies
View Related
Feb 19, 2012
I would like to make a design with 4 Nexus 5596UP. 2 of them equipped with Layer 3 Expansion Module so they can serve as core layer and the other 2 Nexus used as Layer 2 for aggregation server layer.The 2 Nexus in the core layer will run HSRP and will peer with ISP via BGP for Internet connection The 2 Nexus in the aggregation layer will be configured as layer 2 device and have FEX and switches connected to them.What I am ensure of is how the vpc and port-channel configuration should look like between the 4 nexus. What I was thinking is to run vpc between the 2 Nexus in the aggregation layer and between the 2 Nexus in the core layer. Than I was thinking of connecting each Nexus in the aggragtion layer to both Nexus in the core layer using port-channel and vice-versa.
View 3 Replies
View Related
Dec 17, 2012
how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
View 2 Replies
View Related
Mar 29, 2012
I wanted to ask a question about the diagram I have included. We are bringing up 2 MPLS WAN connections and would like some specifics on the best design. We are using BGP to the providers. From there we have big questions. We can run BGP internal and are licensed to do so on the N5K's. The N5Ks are currently using HSRP for inside LAN clients as default gateway. We want to load balance and provide redundant routes using a dynamic approach. Should we use BGP internal utilizing the connections between the routers? Should we use HSRP on the routers? How best to get the routes to the N5K and should we be considering this?
View 5 Replies
View Related
