My home desk top is set up with D-Link Xtreme N Dual Band Router. I have no problems accessing the internet on my desk top computer. I am trying to access my home wireless network through my HP laptop computer. The wireless network status is Limited or no Connectivity. I've tried the "repair" button with no resolution. The wireless connection is set to automatic.
View 1 RepliesRegion : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225
ISP : Rogers
Ever since upgrading my firmware from 120426 to the latest(121225), one of my computer(windows xp, TP-link Nano) is frequently losing internet connectivity.I purchased the router a month ago and firmware 120426 was the version that came installed. The router would stop working about 3-4 times a week, requiring me to reboot it. Because of this I did some research online and found out about version 121225 which supposedly should improve performance and stability. After the firmware upgrade today I noticed that one of my computer is having a lot of trouble maintaining internet connectivity for more than 30 minutes. When checking wireless connectivity it would say that I am connected and that the signal strength is excellent. I'm also able to ping 8.8.8.8 but not www.google.com(I've tried ipconfig /flushdns and it doesn't solve the problem). I also have trouble accessing or pinging the router(192.168.0.1) with this computer.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
The router is working and when I plug in an external drive to usb I can see in the admin tool. It is setup to share without a password. I am using a PC with Vista on it...so I go to RUN and enter [URL] but I get the following message:'Windows cannot access [URL]
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :
Setting up access control for one PC. I just want to block all internet access to one PC during a certain time. It seems like my only options in the Access Control page in the GUI is to block websites or domains.
Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : 3.13.23 Build 120810 Rel 44064nHow do I configure the TP-Link N750 wireless router model TL-WDR4300 as an access point so that computers/nodes on the WAN, LAN and wifi connections of this device are all on the same network/subnet?From the admin browser page, disabling DHCP and NAT does not provide the desired results.
View 10 Replies View RelatedRegion : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_120820
ISP : Cox cable
It doesn't matter how I set it up, once the policy is enabled nothing can get through. This is the same for "deny" or "allow" as default. Is there bug with this new firmware TL-WDR3600_V1_120820??
Region : Brazil
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.17 Build 120509 Rel.33890n
I have a notebook connected by Wireless and a desktop connected by cable.Sometimes my wireless connection are limited, but my computer (connected by cable) still working fine.I`ve tried to disable DHCP and input static IP address but I didn't work.I have used for almost one week without problem, and sometimes this problems happens three times in one hour.The only way to reconnect the wireless is restart the TP-LINK and my internet modem.I`m using the latest firmware version.
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.31 Build 130319 Rel.57876n
ISP : BT Infinity
I have 11 wireless devices connected to WDR4300. These are PCs, phones, tablets, PS3 etc. All devices have assigned DHCP addresses.I have read lots of faqs and searched the web, but still can not figure out a simple way to achieve the following:
I would like some of my devices have NO access to the Internet from 2200 to 0600.
I am currently looking to upgrade and extend my home network with preference to dual band and gigabit functionality. My problem is choosing the correct hardware.I want dual band to separate the network for the kids (a PC, laptop, Xbox 360 and phones all wireless) and set up parental controls and maintain connection speeds etc. For my needs I need the network to be connected to my Onkyo AV Amp (for internet radio and music streaming only), Blu-ray Player, Sky HD satellite box (all wired) and a PS3 (pref wired) and a few wireless devices all N capable. Apart from the obvious gaming capability I would like to be able to stream HD video to the PS3, PC (wired) and laptops via a USB HDD connected for now on an access point or modem router to save on the cost of having separate networked devices.
I currently have ADSL so I was looking to get a dual band gigabit modem router to serve the kids wireless hardware whilst my current hardware is on another floor and is connected with a wire from the existing modem but I have to keep swapping it from PS3 to amp etc.In short I am hoping to have a gigabit, dual band ADSL modem router and connect to a gigabit access point (with dual band if possible) via the cable I have sent to the other floor to wire up the 4 devices. I've currently been looking at Netgear and Buffalo solutions as I've had problems with Linksys and Belkin routers in the past. Would this be possible with just 2 devices (modem router and access point) whilst maintaining decent speeds and if so can someone shed some light as to what I should get.
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : VIMPELCOM
To access USB Storage in Windows I simply type "\tplinklogin.net" in Run window.But how can I access it using Adnroid phone or tablet connected by Wi-Fi?Typing "\tplinklogin.net" in Browser adress line brings me to Google search, typing simply "tplinklogin.net" opens router web interface..
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
I am trying to restrict external access to a ftp server I have running, to a single external IP address. Is this possible? It can be done for the Remote Management IP Address page, where you can enter a single address or 255.255.255.255 to allow all external hosts. But the set up of a virtual server does not appear to have that option.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.17 Build 120426 Rel.29216n
ISP :
In the absence of true QoS capability on the 4300, what is the best way to give bandwidth priority to one of my network devices?
I have an Apple Airport Extreme connected to my network. It is used to stream music from my Ipod to my sound system. I do this through my network (rather then connecting the IPod directly to the AE) so that I can connect to radio stations over the internet. The problem is that I'm getting random dropouts (pauses in streaming). I've shut down everything on the IPod to make sure that there are no Apps competing for WIFI resources. The dropouts happen even if there is little activity on the network (e.g., file downloads, youtube, etc.)
What I want to do is to get the 4300 to give top priority to the AE. How can I do this without QoS capability? Can I allocate more bandwidth to the AE when it is receiving streaming data?
Note: The AE is always connected to the network. It uses DHCP to get it's IP address. It is connected to the 5G band. Signal strength is typically 1 to 2 of 3 bars (average is 1.5 bars). The 2.4G band has a slightly higher signal strength but the same dropouts occur so the problem does not appear to be signal strength.
Region : Singapore
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : starhub
1) Always auto disconnect (limited access),
2) My smart phone Motorola MB860 (android 4.0.4) Can connect but can access internet.
3)Always connect to 2.4GHz ,never see connect to 5GHz.
4)Wireless connection 15-20 Max Mbps Only ,LAN can up to 50 Mbps .
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_130320
ISP :
Has anyone gotten the Guest Network feature to work from the new firmware TL-WDR3600_V1_130320?I have my WDR3600 setup as an access point:TPLINK with static IP address connected via ethernet cord from the LAN port and connected to the main Verizon FIOS router which distributes DHCP IP addresses to the netwrok. Can not get the Guest Network feature to work - I see the guest SSID I created but when I connect to it, the IP address assigned is in the 169. range meaning it does not get to my main router.It may be because I have the TPLINK setup as an access point, so are there any people who have gotten Guest Network work either with the TPLINK as the main router or as an access point?
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I have a client that has a WR2543ND (House) and WDR4300 (Office/Internet) router that are located in two separate buildings about 40ft apart. He has each one hooked up to external antennas connected on the outside of the buildings. Back in December I got WDS working between the two routers and the PC in the house was able to use the Internet in the Office as well as share resources between the office and house computers. Two days ago I was down there working on his network and I was having problems setting up network shares. I discovered I wasn't able to ping from the Office PC to the House PC or vice versa and what's even stranger, I couldn't ping the House PC from the House Router (WR2543ND). I checked WDS status and on the House Router is says "Run" but on the Office Router it says "Int" but the WDS is definitely up because I am able to ping from the Office Router to the House Router, plus I am able to use TeamViewer to connect to the House computer from the Office computer. There are no firewalls enabled on Windows. Lastly the DHCP server is only running on the Office Router.
Region : Singapore
Model : TL-WDR4300
Hardware Version : V1
I need to set up remote access to my HDD connected to my WDR4300, so I can always go online when I am out to retrieve the saved files in the HDD. However I have zero knowledge of network setting of the FTP servers, I can gain access when I am home and connected to the Wireless network, but how to gain access remotely.
Can I put more than one N300 Dual-Band Wi-Fi Range Extender on my home network?
View 4 Replies View RelatedRegion : India
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
i need to create a network with four computers and i have a tplink gigabit switch(wired) and plan to buy a dual band wifi gigabit router the sending and receiving end are just about 10 meters and are parellel that is i have to transfer and share data across street i plan to use one of the computer as primary data server and one of computer wired in with it with cat 6 cable and two others across street with wifi the transmission has to be lossless as its accounting and varous other files are being shared?
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP : Verizon DSL
My DSL connection comes into our house in the basement and the DSL modem came with a router included. I bought the WDR4300 for the higher speed wireless connections and the gigabit ports. I really don't need the "router" functionality. I would like to put the WDR4300 on the second floor to give (hopefully) the broadest wireless range. However, I would like all my PCs (including those wirelessly connected) to be on the same sub-net. Is there a way to configure the WDR4300 so it acts like a switch rather than a router?
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : fullrate.dk
My ISP has provided me a router: Zyxel P-2601HN which has an ideal WLAN transfer rate of 150 mbps. I live in a concrete 2 story house so signals are weak at best on the other floor - therefore, I Have bought the TL-WDR4300 as an extension for the latter floor. I have connected the routers from LAN to LAN and the Zyxel has 192.168.1.1 on LAN and the TL-WDR4300 had 192.168.0.1 as out set. I have changed this to 192.168.1.2 and all the setup (disabled DHCP + other) seems to work alright. BUT i can not log into the TL-WDR4300 !! Not with http://192.168.1.2 and not with [URL]. What I can do to get into the setup of TL-WDR4300. I know I can alays backup the setting and reset the router and load the setting again, make alterations, saving .....but it kind of drastic !Can the two radios SSID names (2,4 MHz and 5 MHz) be the same name as the SSID name on the Zyxel P-2601HN ? What are the implications ?
Region : Germany
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : V1
ISP : Kabel Deutschland
the firmware offers 3 different dyndns services. But opendns is not included, also there is no free field to choose protocol, server, password and network. Will this be updated in further firmwares?
Region : Brazil
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.6 Build 110923 Rel. 53137n
ISP :
I'm trying to use TL-WR2543ND to connect 50 tablets to my wireless network, but as it establish around 20 connections, no other tablet is able to connect to it.
I've made no custom configuration to the wireless settings of the router. Is there anything a need to do to get the 50 connections?
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 1
ISP : cox.net
I have downloaded the file TL-wdr3600_v1_130129.zip. Extracted the file to a temp folder. Thje file is a bin file which is a bin image wdr3600v1_en_3_13_26_up(1301).bin. I do not see any flash file to load this to the router.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Teksavvy
how can I see who connected to my router?
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : Latest
ISP :
The UDP connections are being blocked when I use my VPN. I can connect for a while but soon after a while, the connection doesn't work. I can't even access the router page.
Region : Canada
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.17 Build 120426 Rel.29216n
ISP : Bell Canada
Just had my line upgraded to 50mbit down, and 10mbit up. Whenever the router is between the PC and the modem, my speeds drop to 30mbit. If i plug directly into the modem, I get the full 50Mbit. Upload speeds are always 10mbit.I've tried power cycling devices, and even replaced all cables with cat6 (which I know isn't the issue, but i'm just trying to eliminate everything)
Region : Philippines
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : Smartbro WiMax
I'm using the router TL-WR2543ND, I have pesonally configured the router myself, I'm no that good in computer but I managed to do so. I never had difficulty doing it. I have decided to switch to Smartbro Wimax and tried to connect it to my tp-link router but no luck. I browsed the net for possible instructions to do it but just frustrates me. I have changed the IP address of the router to avoid conflict, cloned the MAC address, still unable to connect the router.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
ISP : Comcast
TP-LINK WDR4300 750N Dual-Band router issue.
I started having a problem with a VONAGE V-Portal VoIP adapter losing connection to the Vonage server. I Unplugging the adapter and waiting doesn't solve the problem. The only way I can temporarily fix the issue is to reboot my TP-Link router. Once the router is rebooted the adapter can connect to Vonage. After a few hours it loses connection again. I have set the adapter to use a static IP outside of the DHCP reserved pool. This didn't fix the issue.
I have had vonage for many years and this router for the last 10 months and not had a problem until the past two weeks. Nothing only my local network changed. All of my PC's have no problems with internet access during the time that the Vonage adapter gets an Error 004 (lost connectivity). I still have connectivity with my ipod touch and other internet enabled devices as well. I was using 8.8.8.8 as my DNS server in the router DHCP configuration as well as the static value when I tried using a static IP with the V-Portal. I then switched all system to the ISP (Comcast) preferred DNS servers. The problem still exists. The only way to get the Vonage adapter back to running is to reboot the router.
I should mention I have Motorola Cable modem to a TP-LINK WDR4300 750N Dual-Band router. I have two Vonage vportal adapters plugged into the a couple of the LAN ports on the TP-LINK router. One vportal is my roommates, one is mine. Everything has been working fine for the last 6 months and now one or the other Vportal loses communication through the router, but the other vportal doesn't lose connectivity. It only happens to one of them and it varies as to which one will ERROR out.
Region : Ireland
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Smart
I have
A TP-Link TD-8817 Modem with IP Address 192.168.1.1
A TP-Link TL-WDR-3600 Router with IP Address 192.168.0.1
A PC with IP Address 192.168.0.100
I figured out that I can only enter an IP Address with the range 192.168.1.* when port forwarding on the modem, ie I cant enter 192.168.0.100 for the PC.Is there any way of Port Forwarding to the PC?
Region : Germany
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : Build 121225 Rel.37950n
I have low signal range from this WDR4300 router on both bands and especially on 5Ghz i lose my connectivity on just few meters away from the router and on other rooms in my 80m2 apartment, i also own another tp link 740n with only one antenna and the range is better with it almost covers all my apartment. Router has been reset after being updated to latest firmware and tried different configurations but im not satisfied with the signal range. Is there something i can do.
I have the new XBOX 360 black N wireless adapter and the Linksys E3000 dual band router as I want to upgrade the network range and speed to N. I set up a unique SSID and passphrase (WPA2) for both 2.4GHz and 5GHz bands. My XBOX could connect to the 2.4GHz band network and could connect to XBOX Live. But when I configured all the settings and tried to connect to the 5GHz band network, but no luck. My XBOX just said it failed to connect. I was sure that I did type in the SSID and passphrase correctly. I still cannot figure out what went wrong. I even suspected either the wireless adapter or the router malfunctioned.
View 9 Replies View RelatedRegion : Germany
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP :
all my systems are configured under "IP & MAC Binding". Binding is activated globally and all check marks for every ID are set. After i finished my configurations, the "ARP List" status shows, that everything is bound - so far everything is great. The problem appears after a router reboot or after shutting the router down and powering it on again. The "ARP List" then shows only a few of my IDs and their status is unbound. I need to go back to the "Binding Settings" and hit "Save" - after that all my IDs appear in the ARP-List and everything is OK again.