Region : UnitedStatesModel : TL-WDR4300Hardware Version : V1Firmware Version : 3.13.23 Build 120810 Rel 44064nHow do I configure the TP-Link N750 wireless router model TL-WDR4300 as an access point so that computers/nodes on the WAN, LAN and wifi connections of this device are all on the same network/subnet?From the admin browser page, disabling DHCP and NAT does not provide the desired results.
View 10 RepliesRegion : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I will never ever buy anything Chinese bricked.
I just bought a new D-Link N750 DIR-835 Dual Band Router, and I tried installing it to apparently no avail. I used the installation CD and followed all the instructions carefully throughout, but once it was "working," I did a speed test and saw that there was absolutely no difference in speed.
I refuse to believe that this new router, which cost me over $100, would provide no noticeable difference over my old router. Speaking of my old router, I have the original router that Telus sent me for free. It's a Siemens Gigaset SE567, and I've dealt with it a few times when I had internet problems,fiddling with the 192.168.0.1 web address site, configuring the passwords and SSID, and the like. I'm not super-educated on the matter,but I know enough about it that with a thorough explanation, I could probably perform whatever is necessary.
Anyways, like I said, I followed all the instructions and after testing out some simple Youtube videos on both my tablet and laptop, through the wireless network that resulted, it couldn't even load a 480p video without lagging. I know that the router isn't the only thing that ensures speed, but even with my (probably barebottom) internet plan (which my father set up, not me, and knowing my father, it's probably the slowest connection available), I just cannot believe that the resulting network was the best speed available to me. So did I do something wrong? Are the routers interfering with each other? Is that actually the best speed I can achieve? Is that Gigaset even a router? Or is it a modem? Or both?
Region : Singapore
Model : TL-WDR4300
Hardware Version : V1
I need to set up remote access to my HDD connected to my WDR4300, so I can always go online when I am out to retrieve the saved files in the HDD. However I have zero knowledge of network setting of the FTP servers, I can gain access when I am home and connected to the Wireless network, but how to gain access remotely.
I am currently looking for informations about access point 2602e, more precisly about antennas.This AP have four RTNC connectors for external antennas, but I found these table into Cisco documentation: [code] When I see that, I understand that we only need, to transmit, three antennas with 2,4 Ghz (which is the only band we will use in a first time), but four with 5 Ghz.I also found these informations, in the same documentation:The 2602E models are configured with up to four external dual-band dipole antennas, and two 2.4-GHz/5-GHz dual-band radios. The radios and antennas support frequency bands 2400–2500 MHz and 5150–5850 MHz through a common dual-band RF interface. Features of the external dual-band dipole antennas are:
• Four RTNC antenna connectors on the top of the access point
• Three TX and four RX antennas
My question: with four antennas, we have three TX and four RX, is it for 2,4 Ghz, 5 Ghz or both?
I'm networking a clients home and he specifically wants dual-band wifi through-out. Now he has a fairly large 3 story house, and wanted to place an access point on the top floor to be assured he'll have strong and reliable signal. He's going to have multiple TV's wired into the network, as well as computers, laptops, phones, a Xbox 360 and a PS3. Were using Gigabit switches and a D-link Simultaneous Dual-band Gigabit router.The modem, router, and main 16 port switch will be in his basement in a semi-server room. He currently has 12 lines run throughout his house, 3 to the top floor, 5 to the main floor, and the ability to lay some in the basement if he needs. The 16port switch will plug into the router, I'm also putting an 8 port into the router from the main and top floor. The remaining lines will plug into the switch in the basement. On the top floor I was going to install an AP or Router turned into an AP into the 8port switch.Now the only reason I am considering using a router instead of just getting an AP, is that neither of us can find a simultaneous Dual-band AP. It seems the only simultaneous DB out there is in routers. So, my question is, will I be able to easily use a router as an AP AND get simultaneous Dual-band out of it if I do so? Is there a Simultaneous Dual-band AP on the market that would a better investment?
View 1 Replies View RelatedHow do I utilize the dual band feature on my belkin N750 DB? Do I have to set up two separate networks? Even then how when my devices PC, iPod, gaming devices are only recognizing the 2.4GHz band network?
View 3 Replies View RelatedI'm very dissatisfied with the range and signal strength of my new WRT610N dual band router compared to the WAP54G Access Point I used before.Can I configure the Access Point as a repeater for the 2.4 GHz band on the WRT610N if I use the WRT610N as a Wireless G router rather than wireless N?
View 5 Replies View RelatedRegion : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
The router is working and when I plug in an external drive to usb I can see in the admin tool. It is setup to share without a password. I am using a PC with Vista on it...so I go to RUN and enter [URL] but I get the following message:'Windows cannot access [URL]
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP :
Setting up access control for one PC. I just want to block all internet access to one PC during a certain time. It seems like my only options in the Access Control page in the GUI is to block websites or domains.
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : TL-WDR3600_V1_120820
ISP : Cox cable
It doesn't matter how I set it up, once the policy is enabled nothing can get through. This is the same for "deny" or "allow" as default. Is there bug with this new firmware TL-WDR3600_V1_120820??
Region : Brazil
Model : TL-WR2543ND
Hardware Version : V1
Firmware Version : 3.13.17 Build 120509 Rel.33890n
I have a notebook connected by Wireless and a desktop connected by cable.Sometimes my wireless connection are limited, but my computer (connected by cable) still working fine.I`ve tried to disable DHCP and input static IP address but I didn't work.I have used for almost one week without problem, and sometimes this problems happens three times in one hour.The only way to reconnect the wireless is restart the TP-LINK and my internet modem.I`m using the latest firmware version.
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.31 Build 130319 Rel.57876n
ISP : BT Infinity
I have 11 wireless devices connected to WDR4300. These are PCs, phones, tablets, PS3 etc. All devices have assigned DHCP addresses.I have read lots of faqs and searched the web, but still can not figure out a simple way to achieve the following:
I would like some of my devices have NO access to the Internet from 2200 to 0600.
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : VIMPELCOM
To access USB Storage in Windows I simply type "\tplinklogin.net" in Run window.But how can I access it using Adnroid phone or tablet connected by Wi-Fi?Typing "\tplinklogin.net" in Browser adress line brings me to Google search, typing simply "tplinklogin.net" opens router web interface..
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
I am trying to restrict external access to a ftp server I have running, to a single external IP address. Is this possible? It can be done for the Remote Management IP Address page, where you can enter a single address or 255.255.255.255 to allow all external hosts. But the set up of a virtual server does not appear to have that option.
Region : Singapore
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : starhub
1) Always auto disconnect (limited access),
2) My smart phone Motorola MB860 (android 4.0.4) Can connect but can access internet.
3)Always connect to 2.4GHz ,never see connect to 5GHz.
4)Wireless connection 15-20 Max Mbps Only ,LAN can up to 50 Mbps .
Region : UnitedStates
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP : Centurylink
I'm using a WDR3600 router, and I'm having difficulty with getting internet access on the 5 GHz band. Right now the router is broadcasting in both 2.4 and 5 GHz as two separate APs. The 2.4 GHz band works perfectly fine, but when I connect to the 5 GHz band my device is not assigned an IP address and cannot connect to the internet (or even the router configuration page). Unfortunately, I don't have another device capable of accessing the 5 GHz band, so I can't check to see if the computer is at fault, but both the computer and the router have worked together with no problems before, and this computer has done fine in accessing other 5 GHz bands.
My home desk top is set up with D-Link Xtreme N Dual Band Router. I have no problems accessing the internet on my desk top computer. I am trying to access my home wireless network through my HP laptop computer. The wireless network status is Limited or no Connectivity. I've tried the "repair" button with no resolution. The wireless connection is set to automatic.
View 1 Replies View RelatedHow can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies View RelatedRegion : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Comcast
I just upgraded my DLink DIR655 to WDR4300. My VOIP service has worked for the last 5 years. But with WDR4300, I'm frequently experiencing dropped calls. The call will be cut off every 20 seconds or so. This is really a deal-killer.
We have 1841 router with HWIC-4ESW we need to config point to point data Dual leased lines failover concept please find attached diagram.
View 3 Replies View RelatedRegion : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23
ISP : Comcast
I have no problems connecting on a 5 GHz band or wired to the router. However any device connecting on 2.4 Ghz gets barely any bandwidth and drops after running for a short time. I have test numerous devices and have the same issue. What was odd is a device on 5GHz that worked fine had the same issue when connecting on 2.4 GHz which seems to say it is only that band. I have an old router that works fine on 2.4 GHz on channel 1 with all the security settings I used on the 4300.
Region : Netherlands
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 130129
ISP :
I've this dualband wireless router since a week.Now I found out, NFS is working very slow (actually NFS is not working at all).I have a Mede8er and a synology NAS server connected to the TP-LINK WDR3600 router.I have movie directories shared on the NAS using NFS.when I go to the NFS locations in my mede8er it takes very long before I can see the NFS mapping.When I connect the Mede8er straight to the Synology NAS server (Cross Cable connection) NFS is working as it should be.So the TP-LINK WDR3600 cannot handle the NFS protocol?
Region : UnitedStates
Model : TL-WDR4900
Hardware Version : Not Clear
Firmware Version :
ISP : Comcast
The internet connection works really well on the 2.4GHz connection and when wired. But when Im connected through the 5GHz network, I get no internet.
Region : Iraq
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Newroz Telecom
Can I replace firmawre TP-Link WDR4300 to DD-WRT to use it?, either my TP-link already has VPN,NAT,QOS,..etc like as DD-WRT so does need to replace firmware for better?
Does TP-Link WDR4300 support with DD-wrt? Is it working clearly without any problem?
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : latest
ISP : Clear
Get GMT throws an error. I set known good public NTP servers, still get error. Also power cycling or rebooting the router seems to drop manual time settings, as well. I am using WDR4300 as a wireless access point, does that matter? Maybe I don't need time in access mode? It is connected to the Internet and is providing internet access to clients.
Region : Venezuela
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP :
I have an issue with my TL-WDR4300 (regular, internet sharing use, no Open WRT or similar things). It was working well, until one day that my devices only receive the 2.4 GHz signal (no 5 GHz) and then I try to connect to 2.4 GHz and it asks for a password. I put my regular password and it doesn't work. Then I tried to bring it to factory default settings, I push the reset button for 8 seconds as the manual points and then same thing. What could I do?
Does the N750 (F9K1103V1) support Guest Access while in Access Point mode? It will not provide an IP address when a guest attempts to connect.
View 20 Replies View RelatedI have a home network, using Belkin N750 as main router and wired ASUS RT-N12C1 which was set as AP mode. How can I find the IP of ASUS RT-N12C1 to change channel?
View 4 Replies View RelatedModel : TL-WR2543ND
Hardware Version : V1
Firmware Version :
ISP : I have an external HDD that I regularly use in any computer I have access.It's an HDD enclosure 2.5" 3.0 USB, with a 750GB WD HDD inside. I use it in computers with all versions of USB, even in my TV. It doens't require an external power source, and just have 01 input/output, which is a USB port.After plugging it in the router (running with the last available firmware from TP-LINK - 3.13.27 Build 121207), I entered the setup screen of the router, and under USB Settings, pressed RESCAN, but the HDD wasn't recognized.What happens is that when I plug it in the router, the LED in it starts blinking (in normal usage, the LED becomes red for a couple of seconds, and then becomes steadly blue, when it gets connected into a equipment). It is probably a matter of power, as if the router wasn't providing enough power to it when it's plugged.Afterwards, I've made the following tests:
1) Used this External HDD in 3 different equipments (a notebook, a netbook and a TV), with different versions of USB ports. It was recognized and read normally in all of them.
2) I tested a pendrive with the router. After RESCAN, it was shown normally in Storage Sharing page.
3) I have downgraded the firmware to 120509 version, plugged the HDD in the router, and once again, it was an unsuccessful try.
What I can conclude from those tests is that:
1) My External HDD is working normally;
2) The router's USB port is working properly;
3) So, if both are working, it can only be a matter of compatibility between them.
Region : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : plusnet
How do I get the full 450 Mbps out of my router on the status it saying 300Mbps
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
Region : Others
I have Enable WDS Bridging and run Survey which detect the other SSID to be joined with the correct MAC address.I had filled the password of my second THOMSON v 585 V7 with the correct Auth Type both routers broadcast on channel 11.But my TP-Link 2543ND cannot made it work.I also disable DHCP and changed my LAN ip to 192.168.1.2 and can access it over my lan.
Region : Netherlands
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 121211
ISP :
after changing from a Thomson router with wifi to the TP-link WDR-4900 I find that the wifi is very unstable. The 2.4GHz is operating on the same channel as my previous router (channel 8 - which is the lest busy channel around my house), and none of my neighbours have wifi on the 5GHz band. Almost all devices in my home regularly have to reconnect to the wifi, both on the 2.4GHz as on the 5GHz (tested with more than 8 devices). Almost every 15 minutes I see a "wifi channel disconnected" message, 10 seconds later followed by a "wifi connected" message. the Wifianalyser app on my tablet confirms that the wifi signal drops once in a while to zero. I use the latest stable frmware (I read that there is beta firmware but I don't like to loose warranty). The stability seems to unrelated to the amount of traffic on the wifi network.
Will this be fixed in the next firmware of the TP-WDR-4900 ?