Wireless Router N600 Wireless Dual Band Router WNDR3400 - Unable To Connect With Internet?
Feb 7, 2011
The internet at my parents house has recently gone on the fritz..the wireless router is a N600 Wireless Dual Band Router WNDR3400..The computers of the house are able to connect to it..But it does not allow internet connections..The 3 computers are an HP Laptop running windows 7.a Dell Dimension E521 Running windows 7 & and an older HP Walmart special running XP.They can connect to outside systems and through a wired connection to the Modem from Cable vision. They replaced the wireless router and the problem continues.Internet is capable by plugging directly into the Cable vision router,unfortunately do not have the cables to try through the Netgear router to test that out..
Region : UnitedStates Model : TL-WDR4900 Hardware Version : Not Clear Firmware Version : 3.13.29 B 130126 R 50426n ISP : Comcast
1. Any device which is switched off (WiFi turned off) wont be able to connect again without a router reboot. I get a connection timeout error when trying to connect. Happens only when there are more than 3 devices connected. (all my devices are ARP linked to MAC addresses with fixed IP addresses - I thought this would eleminate the problem but not)
2. Streaming videos stop playing after 5 minutes. I have to click on the play button to start the stream again. When I test the internet speed through speedtest.net or speedtest.comcast.net, I get over 40MBPS consistently.
3. The router doesnt recogonize 3TB or above HDDs on either ports
4. As long as all devices connect to one channel (either 5G or 2.4G), the connectivity speed is excellent. The moment a device connects to the other channel, the connection speed fluctuates a lot on both.
Region : Malaysia Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP : TM UNIFI
I have recently bought a dual band router to replace the aging default router supply by the ISP.
After setting up, I found the message "No Internet Connection". I have checked the log and found that PPPoE was connected. However I am connect to the internet.
F9L1101 N600 DB Wireless Dual-Band USB Adapter : recognizing and connecting to wireless network but unable to use internet. Changed static IP adress, etc but no luck. Followed instructions on support email response:
Windows XP:
Start->Control Panel->Network Connections(classic view)->Right click on Local Area connection(wired)/Wireless network connection(wireless)->Properties->Select Internet Protocol(TCP/IP)->Properties->Under General tab, choose "Use the following IP address" and type the IP address, Subnet mask and Default Gateway, DNS and press OK. Type in the ip address 192.168.2.20 Enter the subnet mask as 255.255.255.0 Enter the default gate way as 192.168.2.1 Type in the primary DNS as 4.2.2.2 Type the alternate DNS as 8.8.8.8
Am currently unstalling and reinstalling. The network is WEP with a long alpha numeric key, which was accepted and network detected and connected. No internet. No internet. No internet.
I have a Netgear N600 Dual Band Gigabit Router and my roomate and I both have the wireless xbox and when we connect to xbox live and find a game on call of duty mw2 we lagg our butt off nd we tried changing the channel on the router but it still seems to lag.
I have a Netgear N600 WNDR3700v1 Dual Band Gigabit router and am having a problem with the wired connection with my PC. Everything wireless in the house works fine. In fact, I also have a Direct TV box hooked up for on demand and a sling box hooked up (both wired) and they work find. It's just my PC that is having issues. If I bypass the router and hook straight into the modem, it runs fine also so I have something going on between the router and this PC. I updated the NIC driver and this did not work. Before the update in the device manager, it said it was a NIVIDA nForce Network Controller (if I remember right) and now it says NIVIDA nForce 10/100 Mpbs Ethernet. It was suggested that I change my speed and duplex to match the router after I update but I am unsure what to change it to.
My problem is with xbox live, i have the WNDR 3400 N600 Dual Band Router and i have been experiencing lag spikes since the day i have gotten it. I used to have a wireless adapter and i thought that was the problem so i recently went out and bought a 200 ft ethernet cable so now im hardlined to the router I have the xbox set to highest priority, i have it set with a static ip address for the dmz so i have no restrictions, i have all ports opened just in case, i have great internet speeds : 18.04 mbps download and 4.03 mbps upload and nothing seems to work.. i still have lag that sometimes disconnects me from xbox live and ruins the whole gaming experience.
I have belkin n600 hd wireless dual band n router f7d8301 v1. do i need to do any firmware upgrade? should i down load and install V3 of firmware of V1 only? i want to increase / enhance the range of WiFi.
Region : Malaysia Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 121106 ISP : unifi
i just bought this router and upgraded the firmware. but i cant seem to get Internet connection up and running. it says connected but its not. tried both 121106 and 121226 firmware, still the same. when i checked the connection it says DNS server not responding.
Region : Brazil Model : TL-WR2543ND Hardware Version : V1 Firmware Version : 3.13.6 Build 110923 Rel. 53137n ISP :
I'm trying to use TL-WR2543ND to connect 50 tablets to my wireless network, but as it establish around 20 connections, no other tablet is able to connect to it.
I've made no custom configuration to the wireless settings of the router. Is there anything a need to do to get the 50 connections?
I have the new XBOX 360 black N wireless adapter and the Linksys E3000 dual band router as I want to upgrade the network range and speed to N. I set up a unique SSID and passphrase (WPA2) for both 2.4GHz and 5GHz bands. My XBOX could connect to the 2.4GHz band network and could connect to XBOX Live. But when I configured all the settings and tried to connect to the 5GHz band network, but no luck. My XBOX just said it failed to connect. I was sure that I did type in the SSID and passphrase correctly. I still cannot figure out what went wrong. I even suspected either the wireless adapter or the router malfunctioned.
I recently purchased and successfully installed a NetGear N600 dual band router (WNDR3400). My desktop has no connection issues. My iPod Touch has no issues connecting to the wireless network. However, my phone (HTC Aria), my work computer (Dell Latitude D630 Win XP) and my brand new HP Slate 500 (Win 7 Pro) cannot connect to the network. The network is discoverable by all the devices but the 3 cannot connect. I removed all security and still was not able to connect.
I reinstalled the router and still not able to connect. I restarted the router and still not able to connect. The Dell did previously connect to unsecured networks in my neighborhood but does not seem to like my newly set-up network. I am most surprised that the Slate is unable to connect to the wireless network. I would think something brand new would like that would not have an issue. If I cannot get my wireless router working properly and my other computers able to connect to it, it makes them all pretty useless.
Region : Denmark Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP : Waoo, fiber
i just bought a WDR4300. tried the quick start, then tried to manually set it up like my old Router. but i cant connect to the internet. when i check the status. it often says that WAN is unplugged, no cable. But when i use same cabels and settings on my old router it works fin.
Region : Canada Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP :
Just got my new TL-WDR4300 router. Set it up last night with the latest firmware. I can connect to Internet using a wired cable. However, I can't connect to Internet via wifi. I already tried 2 laptops (Vista & Win XP) and 2 tablets - I can see my wifi signal, connect to it (with my password), even obtained IP address (from ipconfig). However, when I tried to open a web page (eg google), it can't connect to Internet (always got timeout or service not found). Again, same laptop has no problem if I use a cable to connect to my router.
My new Windows 8 computer is not wi-fi capable, I bought the adapter but it only works with Windows 7, they have a link to upgrade to Windows 8 but I don't know where to go from there.
I recently upgraded my d-link router DI-524 for Netgear N600 WNDR3700v3 and every component (wired or wireless) is working except network printer. I have it wired directly to the router and all pcs on the home network can see it, however when i select to do a test print, nothing prints to the printer and i get error. I had this setup using the d-link router with both the printer and the XP PC wired directly to the router and using the XP PC as a network pc sharing the printer to other pcs (Vista / Windows 7) on the home network.The printer is a Toshiba e-studio 160 series.. I re-added the print drivers for XP and still not able to print. Is there anything else I can try?
I have a Netgear N600 (WNDR3400) router, it supports both 2.4GHz and 5GHz networks.My laptop is a Thinkpad T410s with a 11b/g/n Wireless LAN Mini-PCI Express Adapter II.i have enabled both of the wireless networks on the router, and given them different SSIDs. I have updated my wireless drivers to the absolute newest ones. My issue is that my laptop cannot even see the 5 GHz SSID. I was under the impression that any N enabled device would be able to communicate on the 5 GHz network.
Region : Hongkong Model : TL-WDR4300 Hardware Version : V1
During long, heavy download streams (such as BT, video streaming) the router WDR4300 would still lock up the internet (WAN) connection for that client. I could still go to the admin web page on that client but no internet activity would occur until either rebooting the router.
Model : TL-WDR3500 Hardware Version : Not Clear Firmware Version : ISP :
As we say, I followed all the directions but I am unable to setup the ftp server on this router. I even disabled Norton's firewall but am unable to access the server via WAN.
Region : Canada Model : TL-WR2543ND Hardware Version : V1 Firmware Version : 3.13.17 Build 120509 Rel.33890n ISP : shaw
my lenovo 510 running windows 7 has the wirelss router listed in the wireless netowrk connection list but cannot connect to the router. it can connect to other routers without any problem.
So I have a Netgear N600 WNDR3700 wireless router setup at home, and it works great for wireless, but when I plug in my desktop with CAT6 Ethernet cable to the router (didn't bother putting a wifi card in my desktop) for some reason it won't connect to the internet. I know the cable works because I've used it in the past, but for some reason I can't get it to work with my Netgear router.
Out of no where today, my wireless connection has begun saying "No internet access" and I can't go anywhere online Ever since it began happening, it's been saying that for longer amounts of time. So at first it was only a few seconds, now it's been taking a minute until I re-gain internet access. I haven't installed anything or ran any executables lately, don't have any viruses, I obtain my DNS and IP addresses automatically, and a few minutes ago I installed the newest firmware update of my router and I'm still losing internet. I have a NetGear WNDR3400 router.
I just bought a linksys wireless n dual band router e2500 and i want to make my old wrt54g router as an access point. how do i do this and where to start?
Region : Canada Model : TL-WDR4300 Hardware Version : V1 Firmware Version : 3.13.23 Build 120810 Rel.44064n ISP : Bell Canada
We have a WDR4300 router that works well about 98% of the time. We have a static IP address from our ISP configured through PPPoE in the router and are hosting our own email and web server at local IP 192.168.1.200 behind the router. Port forwarding is enabled and working beautifully.
At some times throughout the day, any computer behind the router on our local network is unable to browse to our own website by our domain name (e.g. www.xyz.com) nor by the static IP it is attached to. We also get e-mail errors with mail client configured to use the domain name or the static IP it is attached to as the outgoing mail server. When this happens, I am still able to browse any other site on the internet without problem... just not our own. Also, I have verified that while this is happening (internal computers can access the internet but not our own website):
1) I can browse to our website just fine from a computer outside of our network (e.g. a proxy or a computer controlled remotely from my home)
2) a computer from within the office that cannot reach our website using the domain name or the static IP it is attached to can still reach the website by browsing to the local IP address of the web server (192.168.1.200)
3) the problem seems to resolve itself sometime within 45 minutes of noticing it is occurring if we do nothing. We can make the problem resolve itself sooner by restarting the router.
I have the impression that this problem MIGHT start occurring when users are downloading files from our website. Of course, if this is the case, we cannot simply restart the router to fix the problem because then we are cutting off their download.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : Not Clear Firmware Version : ISP : Verizon DSL
My DSL connection comes into our house in the basement and the DSL modem came with a router included. I bought the WDR4300 for the higher speed wireless connections and the gigabit ports. I really don't need the "router" functionality. I would like to put the WDR4300 on the second floor to give (hopefully) the broadest wireless range. However, I would like all my PCs (including those wirelessly connected) to be on the same sub-net. Is there a way to configure the WDR4300 so it acts like a switch rather than a router?
Region : Argentina Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP : fullrate.dk
My ISP has provided me a router: Zyxel P-2601HN which has an ideal WLAN transfer rate of 150 mbps. I live in a concrete 2 story house so signals are weak at best on the other floor - therefore, I Have bought the TL-WDR4300 as an extension for the latter floor. I have connected the routers from LAN to LAN and the Zyxel has 192.168.1.1 on LAN and the TL-WDR4300 had 192.168.0.1 as out set. I have changed this to 192.168.1.2 and all the setup (disabled DHCP + other) seems to work alright. BUT i can not log into the TL-WDR4300 !! Not with http://192.168.1.2 and not with [URL]. What I can do to get into the setup of TL-WDR4300. I know I can alays backup the setting and reset the router and load the setting again, make alterations, saving .....but it kind of drastic !Can the two radios SSID names (2,4 MHz and 5 MHz) be the same name as the SSID name on the Zyxel P-2601HN ? What are the implications ?
