NetGear WNDR3400 Router - Wireless Keeps Saying No Internet Access?
Feb 18, 2011
Out of no where today, my wireless connection has begun saying "No internet access" and I can't go anywhere online Ever since it began happening, it's been saying that for longer amounts of time. So at first it was only a few seconds, now it's been taking a minute until I re-gain internet access. I haven't installed anything or ran any executables lately, don't have any viruses, I obtain my DNS and IP addresses automatically, and a few minutes ago I installed the newest firmware update of my router and I'm still losing internet. I have a NetGear WNDR3400 router.
View 14 Replies
ADVERTISEMENT
Aug 21, 2011
My 7 month old Netgear wireless router suddenly stopped working
The router's power light will not remain on after powering it up. The only lights that remain on after power-up are the (4) "LAN Port" lights (solid green) and the "Internet" light (solid amber).
The owner's manual states that it's a hardware problem if the power light does not remain on and to call tech support. The tech I spoke too said it's a settings issue that they deal with everyday and not a hardware problem.
One of the things I've tried was using a paper clip to reset the router to it's factory settings. It didn't change anything though. Re-running the setup CD didn't yield any results either. It just stopped in the middle because it said there was no ethernet cable connecting the laptop to the router, even though there was.
By the way... My ISP is Century Link and I use an Actiontec DSL Modem.
Not sure how to modify the router's settings if the network is down.
View 3 Replies
View Related
Jan 23, 2011
I recently got a Netgear WNDR3400 Dual Band Wireless Router. When I first installing it everything seemed to run great, download was about 1.5 Mbps and a good ping, 20-70 for gaming. This lasted about a day. While the download does vary due to the service provider, my ping however has suddenly increased to a constant 200-400. This is happening on my Laptop, X-Box 360, and PS3.I have tested both wired and wireless connections from the router and used both the 2.64Ghz and 5Ghz frequency and I still have the same issue. I have then done a wired connection straight into the modem and my ping returns to the 20-70. My Router is less than 3 ft from all systems. I live in a barracks so there are multiple wireless signals floating about. However no one else seems to have any issues with there ping when using a wireless router and there only 1 room above me. I have changed channels on both frequency's, enabled and disabled NAT Filtering, decreased and increased the MTU size within the WAN settings, reset the router to factory defaults, ensured I have the proper firmware, and proper software for my laptop.
View 8 Replies
View Related
Jul 31, 2011
Familiar with the WNDR3400 but I purchased it when it first came out only to replace it with my E4200. The WNDR3400 has a "wireless repeater function" and I was wondering if it was in any way compaitable witht he E4200 or does it have to be directly connected to use it as an accesspoint/range extender ?
View 4 Replies
View Related
May 14, 2012
I'm looking to be able to access (read and write) a networked external hard drive which is connected to a home router - specifically the Netgear WNDR3400, which has a USB port explicitly for this purpose - from outside the network, via the internet. This is for work purposes (specifically for a small business that I design for). Is this doable? I've been using Dropbox but that's proving too problematic as more and more files need to be managed. I would prefer it not be through software that has to be running on a computer, as there is no "machine" running 24/7 here besides the router itself.
View 1 Replies
View Related
Jun 2, 2011
I recently purchased and successfully installed a NetGear N600 dual band router (WNDR3400). My desktop has no connection issues. My iPod Touch has no issues connecting to the wireless network. However, my phone (HTC Aria), my work computer (Dell Latitude D630 Win XP) and my brand new HP Slate 500 (Win 7 Pro) cannot connect to the network. The network is discoverable by all the devices but the 3 cannot connect. I removed all security and still was not able to connect.
I reinstalled the router and still not able to connect. I restarted the router and still not able to connect. The Dell did previously connect to unsecured networks in my neighborhood but does not seem to like my newly set-up network. I am most surprised that the Slate is unable to connect to the wireless network. I would think something brand new would like that would not have an issue. If I cannot get my wireless router working properly and my other computers able to connect to it, it makes them all pretty useless.
View 4 Replies
View Related
Feb 25, 2012
I have a Netgear WNDR3400 router and I would like to just dabble with it and see if I can't get any more performance out of it. I checked dd-wrt already and it isn't supported yet. Any other place to get custom firmware for my router type?
View 3 Replies
View Related
Jul 3, 2012
How do I set up a wireless internet connection for my laptop? The router is a Netgear WNDR3400?
View 1 Replies
View Related
May 30, 2012
I have a Netgear N600 (WNDR3400) router, it supports both 2.4GHz and 5GHz networks.My laptop is a Thinkpad T410s with a 11b/g/n Wireless LAN Mini-PCI Express Adapter II.i have enabled both of the wireless networks on the router, and given them different SSIDs. I have updated my wireless drivers to the absolute newest ones. My issue is that my laptop cannot even see the 5 GHz SSID. I was under the impression that any N enabled device would be able to communicate on the 5 GHz network.
View 4 Replies
View Related
May 16, 2011
I purchased this router, and in reading reviews several people complained how bright the blue "dome light" is. They also pointed out that in the manual there is a way to turn it off. I would like to turn it off, and I have read the manual virtually "cover to cover" (I am after all reading it on my computer), but I did not find any information about this.
View 4 Replies
View Related
May 16, 2011
Now my problem refers to the game Minecraft specifically, but I believe it has more to do with the router than the game, so that's why I am posting on here. To let people connect to your Minecraft server, you need to set a static IP and forward the port 25565. I have followed all of the tutorials for that on this site to the letter, and yet all I can do is make people in my network able to connect. Now before you say this has nothing to do with you guys, I also want to point out that the port checker tool says that port is closed, on both UDP and TCP. For some reason following these guides only opens my port to the network that connects through the router, either wirelessly or wired. So therefore any port checking tools or sites say that it is closed. I have checked my firewalls, turned them off, uninstalled them and that doesn't work. And no, people can't connect through the network unless I forward the ports, so I am actually doing something when I try to forward them. I am running Windows Vista x64-bit
View 1 Replies
View Related
Feb 6, 2011
Recently got a Netgear N600 WNDR3400 router. It works fine, aside from that fact that servers either have - or 999 for a ping.
I have not had this issue with my older Linksys router. What do I have to do to set up this Netgear? How to get BFBC2 to work properly on this router?
View 6 Replies
View Related
Feb 7, 2011
The internet at my parents house has recently gone on the fritz..the wireless router is a N600 Wireless Dual Band Router WNDR3400..The computers of the house are able to connect to it..But it does not allow internet connections..The 3 computers are an HP Laptop running windows 7.a Dell Dimension E521 Running windows 7 & and an older HP Walmart special running XP.They can connect to outside systems and through a wired connection to the Modem from Cable vision. They replaced the wireless router and the problem continues.Internet is capable by plugging directly into the Cable vision router,unfortunately do not have the cables to try through the Netgear router to test that out..
View 3 Replies
View Related
May 30, 2012
I have my ethernet cable hooked up to a WNDR3400 router, and my internet connection will drop for an instant randomly (usually happens at least once every 5 minutes) it then instantly reconnects. The problem is that when i'm downloading stuff, the disconnection will cause the download to fail and i'll have to restart from the beginning (making larger files impossible to download). Also, I have an xbox in the same room connected to the router via wireless. It also has the same issues of dropping and reconnecting and that causes me to get kicked out of live.Interestingly enough, my laptop, connected to the internet via wireless does not experience this issue when used in (or outside of) the room.
View 4 Replies
View Related
Aug 20, 2012
Have two other computers that connect with ease to the Netgear wireless router, but the new computer will not access the internet. I have been searching for answers and have tried about everything I can find nuder similar posts, but I still have not internet access. At varying times, I have had "internet access", but no actual ability to load websites. Right now, I do not even have access. I am at a loss.Even at my low level of experience, I am usually able to tinker until I fix the problem, but I am about four hours in and currently seem to have taken a step backward. I cannot even begin to explain what things I have already tried
View 9 Replies
View Related
Aug 25, 2012
My Dell Laptop is unable to access internet through my Netgear wireless router. Other equipment (Lenovo laptop, ipad, iphone, PS3) accessing internet fine through same router. I ran the onboard Dell Wireless WLAN Card Utility. Hardware diagonistics all pass. Connection diagnostics reports:
Radio Passed
Association Passed
Authentication Passed
Local IP Address Passed
[code]....
View 1 Replies
View Related
Mar 23, 2011
Every day for the past week my Internet access goes down. I have a netgear router connected to Comcast modem. I have to reset the modem then the router constantly and it gets irritating. I called comcast and they say reset them. But why should I have to constantly reset.... Sometimes I just ignore it and it comes back up later... what is going on??
View 1 Replies
View Related
Sep 2, 2012
i bought the netgear wgr614v10 router yesterday from yesterday i was trying to connect to wifi but i could setup
View 3 Replies
View Related
Feb 15, 2013
I've been able to duplicate my problem by using another WinXp computers instead of a USB drive plugged into my router. Same exact problem. So, the bottom line is that I can access (and modify) the files across the network if I'm doing so manually, but my Windows service fails when trying to do the same thing. If I run the program through Visual Studio, it works. If I run that same exact code as a Windows service, it fails.
I've created a Windows service that needs to access a common network location. To test it at home, I plugged a USB drive into my Netgear N600 WNDR3400 router. The USB storage settings show the workgroup name as Workgroup, and the file path is. [code]
View 1 Replies
View Related
Dec 5, 2011
I replaced a Netgear router with a similar Netgear router, but the LAN is no longer working.The old Netgear router would drop internet, but LAN would work. Replaced it, the new Netgear router works fine with the internet (cable modem), but the LAN with two computers will not work. The desktop with Windows XP, and a laptop with Windows 7. After runing network setups on both computers several times, I have been unable to reestablish the LAN, however internet access via the router is working. Reinstalled the old router and the LAN works fine, allowing file and printer sharing. Old router is a Netgear WGR614v2, new router is a Netgear WNR2000how to reconfigure the router/computers to get the LAN working again with new router.
View 8 Replies
View Related
Jul 9, 2012
I've got a windows server 2003 machine which access internet over a Netgear N150 router also I've got an static IP, now internet is working properly even I can ping my machine from a remote machine.Here starts the real problem, I've shared few folders which I can't access from any remote machine not in my LAN.Although I could access my server through remote desktop and everything else is working fine, I've opened port 445 on router even that didn't worked also Windows firewall is OFF.Now when I try to browse my server through \myserverip it shows me a blank window but when I tried to access it like:
\myserveripsharedfolder it gives me error which reads something like
"File and printer sharing seems online but server is not responding on port 445."
View 10 Replies
View Related
Oct 10, 2011
I got 3 windows 7 pc's at home. IP V6 and IP 4 are enabled. I setup my wireless system and it worked 100%. After 3 months I add a LAN cable to two of my PC's. This is when it all started. My internet browsing became very very slow. When i shutdown the one machine it become fast again. I did the following. Pulled the LAN cable and it was still slow. I then put the cable back and disabled the Wi-Fi and it still was very slow. I rested the defaults and restored my old backup and it still slow. Now I can get any access to the internet any more. I the disconnected the netgear router and take a cheap router with only LAN ports and it work 100%. All the above i did with many router and server reboots.
View 1 Replies
View Related
Apr 13, 2013
I just bought a Netgear Router WNR 2000 v3 and installed it. I got inside the router and could set up a Network Name and security key. However, I can not access the internet when I chose a security password using WPA 2, WPA-PSK + WPA 2 PSK, or WPA/WPA 2. It only accesses the internet when I chose None.( no secured ).At this time, my network is unsecured because there isn't way I can access the internet when I create a security key using the 3 options the router offers.
Note : I have tried the 3 security options creating a key number and my computer connect to the wireless network but don't access the internet. It only access the internet when I select None ( no secured )
View 2 Replies
View Related
Jul 2, 2012
My netgear wireless router (wgr614v9) wont reboot or let me access the internet what should i do.
View 2 Replies
View Related
Apr 29, 2012
I�m trying to get an old Dell XP laptop (g wireless adapter) working with my new Net gear (wndr3400) dual band router and hit a wall. No problems on my tower. No problems with a newer Dell laptop with an adapter or a grandson�s iPhone using the guest SSID. No problems with the TV on the 5.0G side of dual band router using same passphrase key. I see the router/SSID I want but cannot connect. I do not get a prompt for the passphrase/WEP key. I tried to follow instructions from a MS site that seemed to cover my exact problem but the behavior of the Wireless Network display does not follow the script.
Here�s what I do:
1.Right click Wireless Network Connection icon bottom right of screen
2.Select View Available Wireless Network Connections
3.Locate desired SSID/router with 5 bars (from router) and double click. Reads �this network requires a network key. It should because I assigned one. 9 ascii, 2 numeric 11 chars total-WPA2-FSK (AES)
4.Click Connect in bottom right of window
5.Entry for the desired router now says validating identity and a pop up box bottom right says windows was unable to find a certificate to log you into the network xxxx where xxx is my SSID.
6.This will sit there saying validating identity for 2-3 hrs with no results.
7.There was never a prompt for Passphrase /WEP key!
If I open up Wireless Network Connections display and select Properties then Wireless Networks tab, select my router connection (only one there) then properties, it shows WEP but network key fields are grayed out. A little bit earlier they were not and I could enter the 11char key but it rejected it as too short. I used to use this laptop for years with an older Lynksys g router.
View 12 Replies
View Related
Jan 6, 2012
How do I setup Netgear WNR2000v2 wireless router as a wireless access point? I just upgraded to a Netgear WNDR3700 wireless router and I don't wanted the wnr2000 to go waste. So basically as the followings:
Internet(modem)---Ethernet cable--->3700---wireless-->2000---Ethernet cable-->Xbox360/PS3.
View 8 Replies
View Related
Sep 4, 2011
yesterday I had switched between my two wireless routers, I went from my Linksys WRTU54G-TM back to my Netgear WGT624v3 because I read that the Netgear provided better range and a bit better speed. I understand that this could be the problem but when I tried to swap out to the Linksys, during the setup, it claims that I have no running internet. The modem is fine, I hooked it straight to my laptop AND my desktop. Now the problem is, I have my desktop and my Xbox 360 connected into the LAN ports, I can connect with my phone and my iTouch wirelessly. My laptop I'm afraid will connect but will not associate with the internet and therefore I cannot access the internet. The Router is a G router and the laptop has a standard wireless g adapter built in.
View 19 Replies
View Related
Mar 3, 2012
My old router (a dlink dir-615) works just fine, but I figured I would upgrade and try to run OpenWRT or DD-WRT so that I could have one VPN for all my devices.
Anyway, I took the router out and followed the instructions (power off modem for at least 1 minute, connect modem to router, router to computer via ethernet, turn on modem first, wait for it to fully boot up, turn on router, wait for it to fully boot up, and then run the setup on routerlogin.net. The router is currently setup and I can connect my computer or iphone to it just fine, but I cannot access the internet. It doesn't make a difference whether I'm connected via ethernet or wifi. Either way, I get a "No Internet Access" message from Windows 7.
I've tried turning everything off and starting again. No luck. When I go back to my dlink router, everything works fine again.
So, in short:
Modem + ethernet = internet
Modem + Netgear router + ethernet = no internet
Modem + Netgear router + wifi = no internet
Modem + Dlink router (wifi...haven't tried ethernet) = internet
View 8 Replies
View Related
Nov 17, 2012
I just recently purchased a Net Gear wireless router, I am unable to get on the internet unless I have the ethernet connected to my laptop.
View 1 Replies
View Related
Oct 11, 2012
My laptop says i am connected to the netgear but i am unable to access the internet-
View 1 Replies
View Related
Oct 9, 2011
i have an old Netgear MR 314 router that works like a charm for my wired connections, but whenever i try to connect wirelessly from my phone or laptop, it connects but doesn't access the internet.
View 5 Replies
View Related
Jan 4, 2012
I dont know how to set this Netgear router to make my internet wireless
View 1 Replies
View Related
Dec 12, 2012
I have a Netgear N600 connected to a modem. I want to connect a switch to the Netgear N600, my question is, will multiple computers connected to the SWITCH have access to the internet?
Router : Netgear N600 [URL]
Switch: Rosewill RC-405X 10/100Mbps Switch [URL]
View 4 Replies
View Related
