Netgear WNDR3400 Ports Only Forwarding For Network?
May 16, 2011
Now my problem refers to the game Minecraft specifically, but I believe it has more to do with the router than the game, so that's why I am posting on here. To let people connect to your Minecraft server, you need to set a static IP and forward the port 25565. I have followed all of the tutorials for that on this site to the letter, and yet all I can do is make people in my network able to connect. Now before you say this has nothing to do with you guys, I also want to point out that the port checker tool says that port is closed, on both UDP and TCP. For some reason following these guides only opens my port to the network that connects through the router, either wirelessly or wired. So therefore any port checking tools or sites say that it is closed. I have checked my firewalls, turned them off, uninstalled them and that doesn't work. And no, people can't connect through the network unless I forward the ports, so I am actually doing something when I try to forward them. I am running Windows Vista x64-bit
View 1 Replies
ADVERTISEMENT
Dec 1, 2011
I have a problem trying to forward ports needed for steam: my connection to internet looks like this Cisco epc3212 cable modem -> netgear wnr3500v2 ->my pc, all via ethernet cable I set up static ip for my pc and forwarded ports in router but after checking results on web port scanners it only changed from timed out to closed. I have no firewalls, neither on my pc or router, i called my isp and they told me they don't block any ports. I have windows 7. After trying dmz all my ports remain closed except for 3389 which is remote access for windows. I.ve been working on this for past few hours and i'm loosing my mind .
View 5 Replies
View Related
Aug 21, 2011
My 7 month old Netgear wireless router suddenly stopped working
The router's power light will not remain on after powering it up. The only lights that remain on after power-up are the (4) "LAN Port" lights (solid green) and the "Internet" light (solid amber).
The owner's manual states that it's a hardware problem if the power light does not remain on and to call tech support. The tech I spoke too said it's a settings issue that they deal with everyday and not a hardware problem.
One of the things I've tried was using a paper clip to reset the router to it's factory settings. It didn't change anything though. Re-running the setup CD didn't yield any results either. It just stopped in the middle because it said there was no ethernet cable connecting the laptop to the router, even though there was.
By the way... My ISP is Century Link and I use an Actiontec DSL Modem.
Not sure how to modify the router's settings if the network is down.
View 3 Replies
View Related
May 16, 2011
I purchased this router, and in reading reviews several people complained how bright the blue "dome light" is. They also pointed out that in the manual there is a way to turn it off. I would like to turn it off, and I have read the manual virtually "cover to cover" (I am after all reading it on my computer), but I did not find any information about this.
View 4 Replies
View Related
Jun 2, 2011
I recently purchased and successfully installed a NetGear N600 dual band router (WNDR3400). My desktop has no connection issues. My iPod Touch has no issues connecting to the wireless network. However, my phone (HTC Aria), my work computer (Dell Latitude D630 Win XP) and my brand new HP Slate 500 (Win 7 Pro) cannot connect to the network. The network is discoverable by all the devices but the 3 cannot connect. I removed all security and still was not able to connect.
I reinstalled the router and still not able to connect. I restarted the router and still not able to connect. The Dell did previously connect to unsecured networks in my neighborhood but does not seem to like my newly set-up network. I am most surprised that the Slate is unable to connect to the wireless network. I would think something brand new would like that would not have an issue. If I cannot get my wireless router working properly and my other computers able to connect to it, it makes them all pretty useless.
View 4 Replies
View Related
Feb 25, 2012
I have a Netgear WNDR3400 router and I would like to just dabble with it and see if I can't get any more performance out of it. I checked dd-wrt already and it isn't supported yet. Any other place to get custom firmware for my router type?
View 3 Replies
View Related
Jul 3, 2012
How do I set up a wireless internet connection for my laptop? The router is a Netgear WNDR3400?
View 1 Replies
View Related
Feb 18, 2011
Out of no where today, my wireless connection has begun saying "No internet access" and I can't go anywhere online Ever since it began happening, it's been saying that for longer amounts of time. So at first it was only a few seconds, now it's been taking a minute until I re-gain internet access. I haven't installed anything or ran any executables lately, don't have any viruses, I obtain my DNS and IP addresses automatically, and a few minutes ago I installed the newest firmware update of my router and I'm still losing internet. I have a NetGear WNDR3400 router.
View 14 Replies
View Related
Jan 23, 2011
I recently got a Netgear WNDR3400 Dual Band Wireless Router. When I first installing it everything seemed to run great, download was about 1.5 Mbps and a good ping, 20-70 for gaming. This lasted about a day. While the download does vary due to the service provider, my ping however has suddenly increased to a constant 200-400. This is happening on my Laptop, X-Box 360, and PS3.I have tested both wired and wireless connections from the router and used both the 2.64Ghz and 5Ghz frequency and I still have the same issue. I have then done a wired connection straight into the modem and my ping returns to the 20-70. My Router is less than 3 ft from all systems. I live in a barracks so there are multiple wireless signals floating about. However no one else seems to have any issues with there ping when using a wireless router and there only 1 room above me. I have changed channels on both frequency's, enabled and disabled NAT Filtering, decreased and increased the MTU size within the WAN settings, reset the router to factory defaults, ensured I have the proper firmware, and proper software for my laptop.
View 8 Replies
View Related
May 30, 2012
I have a Netgear N600 (WNDR3400) router, it supports both 2.4GHz and 5GHz networks.My laptop is a Thinkpad T410s with a 11b/g/n Wireless LAN Mini-PCI Express Adapter II.i have enabled both of the wireless networks on the router, and given them different SSIDs. I have updated my wireless drivers to the absolute newest ones. My issue is that my laptop cannot even see the 5 GHz SSID. I was under the impression that any N enabled device would be able to communicate on the 5 GHz network.
View 4 Replies
View Related
Feb 6, 2011
Recently got a Netgear N600 WNDR3400 router. It works fine, aside from that fact that servers either have - or 999 for a ping.
I have not had this issue with my older Linksys router. What do I have to do to set up this Netgear? How to get BFBC2 to work properly on this router?
View 6 Replies
View Related
Jul 31, 2011
Familiar with the WNDR3400 but I purchased it when it first came out only to replace it with my E4200. The WNDR3400 has a "wireless repeater function" and I was wondering if it was in any way compaitable witht he E4200 or does it have to be directly connected to use it as an accesspoint/range extender ?
View 4 Replies
View Related
Jul 10, 2012
I'm struggling to set up an SSH router and it always looks like the port is closed...
Here's my set-up
www>D-Link router (ADSL connection)>Linksys router (+Tomato)>Target PC
I have set up the Linksys router to be an SSH server running Tomato as described in many other forums. The "Tomato router" sits behind my ISP-provided D-link-2680 router.
The internal IP of the Tomato router is 192.168.1.200 and if I try: Code:
View 6 Replies
View Related
Feb 15, 2013
I've been able to duplicate my problem by using another WinXp computers instead of a USB drive plugged into my router. Same exact problem. So, the bottom line is that I can access (and modify) the files across the network if I'm doing so manually, but my Windows service fails when trying to do the same thing. If I run the program through Visual Studio, it works. If I run that same exact code as a Windows service, it fails.
I've created a Windows service that needs to access a common network location. To test it at home, I plugged a USB drive into my Netgear N600 WNDR3400 router. The USB storage settings show the workgroup name as Workgroup, and the file path is. [code]
View 1 Replies
View Related
Jun 28, 2012
I have a telephony system already in place with 6 FXO active ports configured on a 2821 Router.The thing is that I am not able to make an ip phone forward calls to a mobile No.I can make calls to the same mobile number when dialed from the phone but the call routing seems not to function correctly when call-forward all is configured on the ephone-dn.I would like to focus only on voice-port 0/0/0 and 0/0/1?
voice-port 0/0/0
supervisory disconnect anytone
output attenuation -3
echo-cancel coverage 32
compand-type a-law
cptone GB
[code]....
View 3 Replies
View Related
Jan 23, 2013
Ports are still closed after forwarding them dont know why am using TP-LINK WR740N.
View 3 Replies
View Related
Apr 30, 2013
I recently signed up with AT&T U-Verse. They required that I buy a 2Wire 3600 HGV router. I looked up how to forward ports -- and even called an AT&T representative -- and I am sure that I forwarded them correctly. I'm trying to host a Minecraft Server. I forwarded port 25565 in TCP and in UDP. After that wouldn't work, the AT&T representative said that the traffic was being blocked from my side. I then checked my Windows Firewall and allowed all proper applications -- Minecraft and Minecraft Server. When that wouldn't work, I went in an manually added exceptions to Windows Firewall for TCP - 25565 and UDP - 25565 Inbound and the same for Outbound. Nothing.I have tried to check the ports in DMZ mode with Windows Firewall disabled -- they are still timing out. What should I do?
View 7 Replies
View Related
Jun 12, 2012
I've been really stumped when I decided to start using xbox live. When ever I try to join my friends party I am slammed with a NAT error. For years now I have not been able to forward ports at all. Any port checkers come back with unable to contact your router.I am fairly certain its the router because, I directly plugged my 360 into my modem and everything worked like a charm.I've read on a similar post found here "Similar post" that updating the firmware might fix the issue?
View 9 Replies
View Related
Dec 5, 2012
I have a network with multiple servers behind a PIX with 6.3 on it. I have one public IP address, and I'm using NAT. I'm currently trying to port my Exchange server to a cloud host, and the vendor is requiring I open up a wide range of ports for MAPI, basically ports 1024 on. What would be the command to forward all of the trafic cominto/from that broad range? if I could simply route all trafic to and from their two IP addresses to my email server, that would accomplish the same end goal.
View 3 Replies
View Related
Dec 16, 2012
Trying to get port forwarding going using ASDM 6.4 on a Cisco 5510
I want to forward port 25/Smtp to 192.168.1.10
I have added all the rules as outlined in the link below. [URL]
But when running an open port checker on [URL]
It says the port is closed, I have noticed that under Access Rules under the Hits columns it says 52 ?
View 7 Replies
View Related
Nov 26, 2011
I have a RV220W with 1.0.3.5 Firmware installed.
I also have a few servers with services I need to expose to outside the network (RDP and some websites) where the external port is not the same as the LAN port. I could accomplish this with my previous router using port forwarding and it looks like I can do the same here on the RV220W but I can't quite get it to work successfully.
View 3 Replies
View Related
Mar 27, 2011
Trying to connect to a computer on a client's network. He has a Netgear WGR614v9 router. I talked him through opening port 23 to 192.168.1.200. I have done this many times on other routers and it should have been simple but could not connect. Had him enable ping response so I could ping his router to verify the connection and ping was good. Tried my port scanner and only port 21 is open. Had client verify the port forwarding data and it is correct. Does he need to restart the router to enable port forwarding?
View 4 Replies
View Related
Jul 31, 2012
How to forward Port 123 on this router?
View 4 Replies
View Related
Oct 20, 2011
Ok, so i never had problems with this before until i reformatted my computer. I have used a program called simple port forwarding and i've also manually added the port seeing if theres a difference, but every time i check my port which is 25565 for a minecraft server it says either failed or not open etc.. I checked netstat -an and it showed it was listening to my ip address and port 25565.
View 6 Replies
View Related
Oct 10, 2012
I'm trying to set up a Minecraft server so I can appear to be a hero to my 8 year old son. I have to forward a port to 25565 adn I've followed all the instructions on how to do this on my netgear DGND3700v2. I've also turned off my Windows 7 firewall, but when I go to a test website, I still get a message saying the port is closed. I don't have a static IP address, is this absolutely critical or does it just mean that the boys will have to log on to a new IP address each time they want to play?
View 1 Replies
View Related
Jul 28, 2011
At work, our proxy blocks everything except for HTTP(S), FTP, and a small handful of other company-specific ports on the _outbound_ connection. On my router, I like to port-forward SSH to my Linux computer server at home but since at work IT blocks out-bound SSH, I have to masquerade the SSH port-forward on my server to get past the corporate proxy. Normally, I've done this in the past by doing something like WAN:9090 (allowed by my IT) --> LAN:22 in my router's port forwards to get SSH routed to my Linux box from the web.
I recently purchased a Netgear FVG318 and it doesn't look like it supports this kind of configuration. In the Security->Firewall Rules->Inbound Rules section of the router configuration I see how to do a port-forward but they only have a drop-down selection of common protocols and will simply 1:1 forward the ports. It doesn't look like it allows to do mis-matched ports on the forward like I'd like to do.
View 14 Replies
View Related
Nov 20, 2011
I have a cable modem hooked up to a Linksys WRT54G2 wireless router, which is hardwired to the computer I use.
I go into the router's menu by going through the standard 192.168.1.1 in the browser, and then go to Applications and Gaming. The port I am trying to open is port 25565 for both TCP and UDP. In the Start and End ports I put 25565, and for the end of the IP Address, I put the last digits of my IPv4 address (10). I used a couple of port checker tools, and it is reporting as still being closed.
View 9 Replies
View Related
May 15, 2013
I've created some port forwards from my public IP (Dialer0) to our private LAN but only the 25565 port forward works. I've even added an any statement to the Nat source list Homenet_NAT. Full config attached. My Cisco router is an 877W. [Code]
View 6 Replies
View Related
Feb 23, 2011
I have set my Netgear WGR614 to a static IP, and I have tried port forwarding but I can't. I've tried disabling SPI Firewall and it still don't work. I have also tried enabling bridge settings on my connection in my modem settings, but that just wouldn't let me back on my internet. How I can port forward?I have a westell 610015.
View 3 Replies
View Related
Dec 4, 2012
I have a Netgear wnr2000v3 Router connected to my Motorola Surfboard Gateway.I have a freePBX Server (virtual running off of VMware Workstation 8) that needs ports 10001-20000 and 5060 forwarded to the server at 192.168.1.110
I added the portforwarding as in this photo:
When I use a port tester it still says "Port 5060 is closed"I have also turned off Windows Firewall. What else could be blocking these ports?
View 3 Replies
View Related
Apr 5, 2013
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Virgin Media Limited
when I forward ports I get the following error message:
Things to note:I have the web GUI running on 8080, because I run a file-server on port 80.
I am using a Virgin media branded router in 'modem mode', this would not cause issues.
I did not do anything to change anything, I went to add an additional port to forward and it didn't work.
I am on a Dynamic IP
After it stopped forwarding, I upgraded firmware to: 3.13.26 Build 130129 Rel.59449n.
View 11 Replies
View Related
Feb 24, 2013
Region : Mexico
Model : TD-W8968
Hardware Version : V1
Firmware Version : the last version of this web page, i forgot number
ISP : TELMEX (infinitum)
i have some problems to configure the port forwarding in my router, don't it work ! but the port number 80 it works with my sub-domain in the internet. after i change this port to 8080 still dont work the port forwarding. the FTP server its ok.
[code]......
View 3 Replies
View Related
Feb 26, 2011
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies
View Related
