Netgear Wnr3500v2 - Ports Closed After Forwarding Before Timed Out?
Dec 1, 2011
I have a problem trying to forward ports needed for steam: my connection to internet looks like this Cisco epc3212 cable modem -> netgear wnr3500v2 ->my pc, all via ethernet cable I set up static ip for my pc and forwarded ports in router but after checking results on web port scanners it only changed from timed out to closed. I have no firewalls, neither on my pc or router, i called my isp and they told me they don't block any ports. I have windows 7. After trying dmz all my ports remain closed except for 3389 which is remote access for windows. I.ve been working on this for past few hours and i'm loosing my mind .
View 5 Replies
ADVERTISEMENT
Jan 23, 2013
Ports are still closed after forwarding them dont know why am using TP-LINK WR740N.
View 3 Replies
View Related
Dec 4, 2012
I have a Netgear wnr2000v3 Router connected to my Motorola Surfboard Gateway.I have a freePBX Server (virtual running off of VMware Workstation 8) that needs ports 10001-20000 and 5060 forwarded to the server at 192.168.1.110
I added the portforwarding as in this photo:
When I use a port tester it still says "Port 5060 is closed"I have also turned off Windows Firewall. What else could be blocking these ports?
View 3 Replies
View Related
May 29, 2011
I have an Acer AX3400 (windows 7). I'm trying to install wireless router Netgear WNR3500v2. I did not succeed sofar. Do I have to uninstall NVIDIA drivers first?
View 1 Replies
View Related
May 16, 2011
Now my problem refers to the game Minecraft specifically, but I believe it has more to do with the router than the game, so that's why I am posting on here. To let people connect to your Minecraft server, you need to set a static IP and forward the port 25565. I have followed all of the tutorials for that on this site to the letter, and yet all I can do is make people in my network able to connect. Now before you say this has nothing to do with you guys, I also want to point out that the port checker tool says that port is closed, on both UDP and TCP. For some reason following these guides only opens my port to the network that connects through the router, either wirelessly or wired. So therefore any port checking tools or sites say that it is closed. I have checked my firewalls, turned them off, uninstalled them and that doesn't work. And no, people can't connect through the network unless I forward the ports, so I am actually doing something when I try to forward them. I am running Windows Vista x64-bit
View 1 Replies
View Related
Oct 25, 2011
I have my 2Wire AT&T U-Verse router properly set up to forward the port 25565 from my machine. (Incidentally, PortForward.com gives me a blank page when I try to look up how to do this.) However, when I test the port is indeed open ( Open Port Check Tool - Test Port Forwarding on Your Router ), it returns as closed. Yes, I'm running the server software while I run the test. I only have the Windows Firewall, but I ran attempts while the firewall was completely disabled as well as with just the appropriate programs allowed.
View 9 Replies
View Related
Oct 12, 2011
i have a 54G wireless home router ..... successfully port fowarded an application from a CPU (server).... but after no connection made from the user to the server..... it suddenly close the application ..... so what i did is to reboot the router in order to refresh the connection ...... Is there any other ways to fix this sudden close of the ports ?
View 9 Replies
View Related
Aug 8, 2012
I have followed all instructions to forward port 22 on my netgear router WNDR 3400v2. It says it forwarded but according to port tracker. Its closed. I am having this with two different locations. All IP addresses are correct and the router can ping them. It just wont open. Using SSH program for port 22 access.
View 10 Replies
View Related
Jan 16, 2012
I have disabled windows firewall in Windows 2003 server control panel but only few ports are shown opened when i scanned with advanced port scanner why other ports are closed.How to open the closed ports?
View 2 Replies
View Related
Dec 18, 2012
We have a WRT610N and are having trouble getting access out to the internet with an FTP client.We are trying to configure Sync2 a program from 4team.biz. It is an MS Outlook application that utilizes FTP servers to host .PST files (outlook data bases) for synchronization.The software has an FTP client built in that can access FTP accounts to store and synchronize the .PST file.
The issue is the WRT610N will not allow this client to connect to our FTP account. We had 4Team’s tech support working on it for a few hours. Ultimately they decided it was my router causing the problem. To demonstrate this to us, they tested ports 80, 21, & 22 utilizing the following websites: url...
All the ports showed either closed or not responding.How do I open these ports so that I can allow Sync2 to communicate with the our FTP account? We are hosting out FTP site at 1and1.com.
View 3 Replies
View Related
Apr 8, 2012
We operate a home office network (workgroup) of 6 older PCs running Windows XP SP3.It's a Windows based network using a designated "home" PC as a server, and until recently we were using ethernet cables and a hub/switch for sharing files which worked well because we only share small document files, no music or video.The workgroup does not have a shared internet connection, we don't want or need one for what we do, although the individual PC's can connect to the web using USB dongles just for checking e-mail.Recently the ethernet hub died and I decided to take the opportunity to upgrade to wireless file sharing.None of the PCs have inbuilt wireless adapters so I bought a D-Link USB wireless adapter for each PC.I also bought a Netgear N300 router, thinking that this was suitable entry level equipment for wireless file sharing. Now I'm not so sure.So far I was unable to install the router on the "home" PC because the installation CD seems to assume that the router will be used for sharing an internet connection and does not seem to offer an installation option without a standalone modem. How to install this type of router to create a closed home wireless network without a shared internet connection.
View 14 Replies
View Related
Jun 28, 2012
I have a telephony system already in place with 6 FXO active ports configured on a 2821 Router.The thing is that I am not able to make an ip phone forward calls to a mobile No.I can make calls to the same mobile number when dialed from the phone but the call routing seems not to function correctly when call-forward all is configured on the ephone-dn.I would like to focus only on voice-port 0/0/0 and 0/0/1?
voice-port 0/0/0
supervisory disconnect anytone
output attenuation -3
echo-cancel coverage 32
compand-type a-law
cptone GB
[code]....
View 3 Replies
View Related
Apr 30, 2013
I recently signed up with AT&T U-Verse. They required that I buy a 2Wire 3600 HGV router. I looked up how to forward ports -- and even called an AT&T representative -- and I am sure that I forwarded them correctly. I'm trying to host a Minecraft Server. I forwarded port 25565 in TCP and in UDP. After that wouldn't work, the AT&T representative said that the traffic was being blocked from my side. I then checked my Windows Firewall and allowed all proper applications -- Minecraft and Minecraft Server. When that wouldn't work, I went in an manually added exceptions to Windows Firewall for TCP - 25565 and UDP - 25565 Inbound and the same for Outbound. Nothing.I have tried to check the ports in DMZ mode with Windows Firewall disabled -- they are still timing out. What should I do?
View 7 Replies
View Related
Jul 10, 2012
I'm struggling to set up an SSH router and it always looks like the port is closed...
Here's my set-up
www>D-Link router (ADSL connection)>Linksys router (+Tomato)>Target PC
I have set up the Linksys router to be an SSH server running Tomato as described in many other forums. The "Tomato router" sits behind my ISP-provided D-link-2680 router.
The internal IP of the Tomato router is 192.168.1.200 and if I try: Code:
View 6 Replies
View Related
Jun 12, 2012
I've been really stumped when I decided to start using xbox live. When ever I try to join my friends party I am slammed with a NAT error. For years now I have not been able to forward ports at all. Any port checkers come back with unable to contact your router.I am fairly certain its the router because, I directly plugged my 360 into my modem and everything worked like a charm.I've read on a similar post found here "Similar post" that updating the firmware might fix the issue?
View 9 Replies
View Related
Dec 5, 2012
I have a network with multiple servers behind a PIX with 6.3 on it. I have one public IP address, and I'm using NAT. I'm currently trying to port my Exchange server to a cloud host, and the vendor is requiring I open up a wide range of ports for MAPI, basically ports 1024 on. What would be the command to forward all of the trafic cominto/from that broad range? if I could simply route all trafic to and from their two IP addresses to my email server, that would accomplish the same end goal.
View 3 Replies
View Related
Dec 16, 2012
Trying to get port forwarding going using ASDM 6.4 on a Cisco 5510
I want to forward port 25/Smtp to 192.168.1.10
I have added all the rules as outlined in the link below. [URL]
But when running an open port checker on [URL]
It says the port is closed, I have noticed that under Access Rules under the Hits columns it says 52 ?
View 7 Replies
View Related
Nov 26, 2011
I have a RV220W with 1.0.3.5 Firmware installed.
I also have a few servers with services I need to expose to outside the network (RDP and some websites) where the external port is not the same as the LAN port. I could accomplish this with my previous router using port forwarding and it looks like I can do the same here on the RV220W but I can't quite get it to work successfully.
View 3 Replies
View Related
Mar 27, 2011
Trying to connect to a computer on a client's network. He has a Netgear WGR614v9 router. I talked him through opening port 23 to 192.168.1.200. I have done this many times on other routers and it should have been simple but could not connect. Had him enable ping response so I could ping his router to verify the connection and ping was good. Tried my port scanner and only port 21 is open. Had client verify the port forwarding data and it is correct. Does he need to restart the router to enable port forwarding?
View 4 Replies
View Related
Jul 31, 2012
How to forward Port 123 on this router?
View 4 Replies
View Related
Oct 20, 2011
Ok, so i never had problems with this before until i reformatted my computer. I have used a program called simple port forwarding and i've also manually added the port seeing if theres a difference, but every time i check my port which is 25565 for a minecraft server it says either failed or not open etc.. I checked netstat -an and it showed it was listening to my ip address and port 25565.
View 6 Replies
View Related
Oct 10, 2012
I'm trying to set up a Minecraft server so I can appear to be a hero to my 8 year old son. I have to forward a port to 25565 adn I've followed all the instructions on how to do this on my netgear DGND3700v2. I've also turned off my Windows 7 firewall, but when I go to a test website, I still get a message saying the port is closed. I don't have a static IP address, is this absolutely critical or does it just mean that the boys will have to log on to a new IP address each time they want to play?
View 1 Replies
View Related
Jul 28, 2011
At work, our proxy blocks everything except for HTTP(S), FTP, and a small handful of other company-specific ports on the _outbound_ connection. On my router, I like to port-forward SSH to my Linux computer server at home but since at work IT blocks out-bound SSH, I have to masquerade the SSH port-forward on my server to get past the corporate proxy. Normally, I've done this in the past by doing something like WAN:9090 (allowed by my IT) --> LAN:22 in my router's port forwards to get SSH routed to my Linux box from the web.
I recently purchased a Netgear FVG318 and it doesn't look like it supports this kind of configuration. In the Security->Firewall Rules->Inbound Rules section of the router configuration I see how to do a port-forward but they only have a drop-down selection of common protocols and will simply 1:1 forward the ports. It doesn't look like it allows to do mis-matched ports on the forward like I'd like to do.
View 14 Replies
View Related
Nov 20, 2011
I have a cable modem hooked up to a Linksys WRT54G2 wireless router, which is hardwired to the computer I use.
I go into the router's menu by going through the standard 192.168.1.1 in the browser, and then go to Applications and Gaming. The port I am trying to open is port 25565 for both TCP and UDP. In the Start and End ports I put 25565, and for the end of the IP Address, I put the last digits of my IPv4 address (10). I used a couple of port checker tools, and it is reporting as still being closed.
View 9 Replies
View Related
May 15, 2013
I've created some port forwards from my public IP (Dialer0) to our private LAN but only the 25565 port forward works. I've even added an any statement to the Nat source list Homenet_NAT. Full config attached. My Cisco router is an 877W. [Code]
View 6 Replies
View Related
Feb 23, 2011
I have set my Netgear WGR614 to a static IP, and I have tried port forwarding but I can't. I've tried disabling SPI Firewall and it still don't work. I have also tried enabling bridge settings on my connection in my modem settings, but that just wouldn't let me back on my internet. How I can port forward?I have a westell 610015.
View 3 Replies
View Related
Apr 5, 2013
Region : UnitedKingdom
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.26 Build 130129 Rel.59449n
ISP : Virgin Media Limited
when I forward ports I get the following error message:
Things to note:I have the web GUI running on 8080, because I run a file-server on port 80.
I am using a Virgin media branded router in 'modem mode', this would not cause issues.
I did not do anything to change anything, I went to add an additional port to forward and it didn't work.
I am on a Dynamic IP
After it stopped forwarding, I upgraded firmware to: 3.13.26 Build 130129 Rel.59449n.
View 11 Replies
View Related
Feb 24, 2013
Region : Mexico
Model : TD-W8968
Hardware Version : V1
Firmware Version : the last version of this web page, i forgot number
ISP : TELMEX (infinitum)
i have some problems to configure the port forwarding in my router, don't it work ! but the port number 80 it works with my sub-domain in the internet. after i change this port to 8080 still dont work the port forwarding. the FTP server its ok.
[code]......
View 3 Replies
View Related
Feb 26, 2011
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies
View Related
May 15, 2013
I just updated the firmware on the WNR1000v3 router. However all the port forwarding configs that were set up previously have become "ghosts". They do not show up on the list nor work, but I cannot add a new entry.
View 2 Replies
View Related
Jul 9, 2013
I have been having problems with my router. I have a Net gear N300 v2, but I am not asking for support with said router. Forwarding network traffic from the Internet to a server and then have it properly re-routed. I have never done this sorta thing before, but I want to go into a career in I.T. when I'm older. As a side note, I have already figured out that ditching the router requires to have a software DHCP server, which I am using Windows Server 2008 Data center and it's built in role as DHCP server.
DNS is also configured. The modem a Motorola Surf Board is connected directly to a Cisco Catalyst 2950, and that connects all of the rest of the network, also via a 3Com SUper Stack Hub, and a little 8-port HP Advance Stack J2610A, which connects to all of my wireless AP.
View 2 Replies
View Related
Sep 16, 2011
I am trying to set up a custom service on my netgear configuration page. I have a netgear router model# Wnr834m. every time i click the "add custom service" button the page redirects to "system authentication failed" and logs me out. What can i do to set up the new port?
View 1 Replies
View Related
May 19, 2011
Can open (url) in work computer but not at home - Message coming up at home that it will be closed for maintenance and that was last week and has since finished now as i can open site at work but not at home
View 1 Replies
View Related
