Linksys Wireless Router :: WRT54G - Port Forwarding Suddenly Closed?
Oct 12, 2011
i have a 54G wireless home router ..... successfully port fowarded an application from a CPU (server).... but after no connection made from the user to the server..... it suddenly close the application ..... so what i did is to reboot the router in order to refresh the connection ...... Is there any other ways to fix this sudden close of the ports ?
I'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me.
I'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
I have a Netgear wnr2000v3 Router connected to my Motorola Surfboard Gateway.I have a freePBX Server (virtual running off of VMware Workstation 8) that needs ports 10001-20000 and 5060 forwarded to the server at 192.168.1.110
I added the portforwarding as in this photo:
When I use a port tester it still says "Port 5060 is closed"I have also turned off Windows Firewall. What else could be blocking these ports?
I was upgrading the firmware of the WRT54G router when the notebook´ screen closed and it went to standby mode. It was stoped the upgrade process.Now only the ports and Internet LEDs light up, but the power LED is off.I also cannot connect to thenavigator for show the administrator´s window. Any procedure to recover the operation of the router in a situation like this?
Port forwarding on my linksys is not seem to be working from outside the network. It works fine if I try on the same network. External ip address: 69.117.132.xxx Ports from 8080 through 8080 forwarded Internal ip address: 192.168.1.150 - static ip address assigned to the webserver. I understand 80 could be blocked by the ISP. Can 8080 also be the same case?
I have the Linksys WRT54G And it was working fine for years! Then today my computer shut down and when I turned it back on there was a connection but my computer was not responding to any commands. The icon shows full connectivity excellent connection. When I try to go to a web page it shows Connection Error and cannot get to any web pages.I am able to get on other wireless connections from neighbors but not mine. I have gone thru different directions on here and I am not technical and don't understand what is being said. I try to go to 192.168.1.1 and it asks for a password which I don't have. I have tried everything such as password and admin and get nothing.I am able to get my ip address and default gateway address and don't know the next step.
My ISP is centurylink and I have a 660 series modem that is both a modem and a router (no wireless). Also I have a Linksys WRT54G v3 wireless router with Tomato Firmware on it. For whatever reason I can't get the port forwarding to work. Yes, I know I have to forward the ports on both and I have tried using this guideurl...Fowarding.php on the modem, with Tomato Firmware it is super simple to forward.
I've got a pretty simple setup where port forwarding was working without a hitch.My old router (wrt54g) was forwarding RDP requests (over 3389) to my computer's ip. No problems. Then I switched it out with a WRT160N wireless router (and upgraded firmware), and I just can't seem to make the connection.
I've followed all the simple tutorials, ala:
Still no luck...! I've ensured my ip is the one the router is pushing connection attempts to, dropped firewall and filtering... still nothing (I've even tried connecting from within the network, using my computer's name) without any success.
I am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
I use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router the port is closed. I followed instruction for port forwarding.
I'm trying to port forward with the Linksys BEFW11S4, I've followed all the instruction from support website. I went to the Application & Gaming then Port Range Forwarding. I changed the settings so I can access this IP remotely. When I try to log into this IP from a different network it wont let me.
I am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use. It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use? I am trying to follow the instructions on [URL] If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.
My first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.
I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.I'm running the latest firmware provided by Linksys/Cisco.
I recently got a e2500 router and set up the port forwarding for my ps3. But then i go to check the ports to see if they are open and they all stay closed.I have no clue whats wrong as I have entered the port forwarding info correctly as I got guideline from portforward.com but still no luck
Im going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?
I have a problem trying to forward ports needed for steam: my connection to internet looks like this Cisco epc3212 cable modem -> netgear wnr3500v2 ->my pc, all via ethernet cable I set up static ip for my pc and forwarded ports in router but after checking results on web port scanners it only changed from timed out to closed. I have no firewalls, neither on my pc or router, i called my isp and they told me they don't block any ports. I have windows 7. After trying dmz all my ports remain closed except for 3389 which is remote access for windows. I.ve been working on this for past few hours and i'm loosing my mind .
I set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
Im trying to open up some ports on my e3000 for the use of Teamspeak and my Teamspeak server. However when i get of the information filled into the single port forwarding under the Gaming & Applications tab, and click save settings. The page just refreshes, with none of the changes being saved.
I am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Linksys E1200 Router not saving Port Forwarding changes.I have tried:
-Restarting the Modem -Restarting the browser -Restarting the computer -Tried to Port Forward through both the Single and Ranged Port Forwarding
IPort forwarding simply does not work with this rounter on Comcast. I called comcast to see if they were blocking ports and they insist they ARE NOT.So what can it be? Was on FIOS with their modem/router combo and port forwarding worked like a charm with them.I've tried single port forwarding, port range forwarding, yada.
I am using the correct internal IP address on the machine I want to enable port forwarding on..Latest firmware is installed 1.04 or whatever (just purchased the router and updated during the Cisco Connect install on the 29th). Guess I should go find a cheaper router that actually works...
I upgraded to a 6500 from a e4200. I use ports 81-84 on test web servers set to static Ip,s when I open the ports nothing can get through from the outside. I can hit the pages internally on those ports and IP's but not from my external ip to those ports. When I set my old router everything is fine.
How to forward a single port to a different port to a specific computer for the WRV210 router?
I would like to forward port 10100 to port 25 to my mail server. There are times when our people are at a hotel and they block port 25 and I have done this in the past on a BEFSR11 and BEFSR41 router. There does not seem to be a Single Port Forwarding setup page and the Port Forwarding setup page only allows you to forward a range to a specific computer, it does not give you a different port you can assign an incoming port to.
I have the most current firmware revision, 188.8.131.52, and Hardware Version WRTR-221G_V01.
I have an E3000 with firnware 1.0.04. A forwarded port is spontaneously changing the IP address assigned to it, but with no change indicated in the singel port forwarding configuration.I have a web server on IP=XXX.XXX.XXX.7, and another device on my LAN with an internal web server at IP= XXX.XXX.XXX.8. The single port forwarding configuration is:
HTTP, external port 80, internal port 80, protocol=TCP, to internal IP address xxx.xxx.xxx.7, enable checked The configuration is saved, and all works well for for hours and/or days and I can use the web host from the intenet as expected. However, after a few days or hours the E3000 suddenly starts sending the http traffic to IP=xxx.xxx.xxx.8 instead of xxx.xxx.xxx.7. When I log in to the router and look at the port forwarding page, it still says it's forwarding the http traffic to xxx.xxx.xx.7 ~ even though all http traffic is being sent to xxx.xxx.xxx.8! I have to reboot the router to get the port forwarding to work properly. If I leave the device at xxx.xxx.xxx.8 powered off, the router seems to work fine for extended periods.
There are no port forwarding services in the router that reference IP=xxx.xxx.xxx.8 , and it does not appear that the port forwarding problem is related to DHCP. All devices on my network have a reserved DHCP address based on their MAC. It does not appear that the spontaneous port forwarding change occurs when when the xxx.xxx.xxx.8 device powers up and gets it's address via DHCP. I have also deleted the xxx.xxx.xxx.8 device from the DHCP reservation table and simply access the device as needed by referencing it's IP, and xxx.xxx.xxx.8 is outside the range of DHCP assigned addresses, and the spontaneous port redirection still occurs once in a while.Is there a known bug where forwarded ports are sent to the wrong IP address?
I just noticed that i have port 10080 open on my router (wrt160nv3). Port forwarding is not configured and web administrative access is only allowed through https (443). DDNS is also disabled, I was wondering why this port is open.
i have a WRT160N V3 and DMZ or Portforwarding dont work.i tried locally following
WAN_PC-> WAN-PORT -> WRT160N V3 -> LOCAL-PORT -> LOCAL_PC The WAN_PC has a Static-IP 192.168.1.2, Subnet 255.255.255.0 The WAN-PORT has a Static-IP 192.168.1.1, Subnet 255.255.255.0 ON the WRT160N V3 i configured a DMZ on 192.168.0.100.and Disabled the Firewall. On the LOCAL_PC (192.168.0.100:8888) is a Apache
So when i type 192.168.1.1:8888 on the WAN_PC i get NOOO Website from the Apache on 192.168.0.100:8888?