Port forwarding on my linksys is not seem to be working from outside the network. It works fine if I try on the same network. External ip address: 69.117.132.xxx Ports from 8080 through 8080 forwarded Internal ip address: 192.168.1.150 - static ip address assigned to the webserver. I understand 80 could be blocked by the ISP. Can 8080 also be the same case?
View 12 RepliesI'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me.
View 3 Replies View RelatedI'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies View RelatedI am trying to open port 12000 on my sky dlink router, been trying for a few days now and i just can't nail it. When i log into router, it brings up the sky router page, any one ever setup port 12000 on the sky router page.
View 1 Replies View RelatedWhen checking my port forwarding, it says that it is not open.
View 2 Replies View Relatedi have a 54G wireless home router ..... successfully port fowarded an application from a CPU (server).... but after no connection made from the user to the server..... it suddenly close the application ..... so what i did is to reboot the router in order to refresh the connection ...... Is there any other ways to fix this sudden close of the ports ?
View 9 Replies View RelatedI have set my Netgear WGR614 to a static IP, and I have tried port forwarding but I can't. I've tried disabling SPI Firewall and it still don't work. I have also tried enabling bridge settings on my connection in my modem settings, but that just wouldn't let me back on my internet. How I can port forward?I have a westell 610015.
View 3 Replies View RelatedWhen checking my port forwarding, it says that it is not open. Why?
View 6 Replies View RelatedI have a WRT54G Linksys router and I am wondering what is the default username and password for port forwarding?
View 1 Replies View RelatedI have a Huawei 523a Router at the moment and I'm trying to setup a IP camera.The Router doesnt allow port forwarding, so my question is can I add another Router onto the Huawei router to allow the second one to work my camera
View 10 Replies View RelatedMy ISP is centurylink and I have a 660 series modem that is both a modem and a router (no wireless). Also I have a Linksys WRT54G v3 wireless router with Tomato Firmware on it. For whatever reason I can't get the port forwarding to work. Yes, I know I have to forward the ports on both and I have tried using this guideurl...Fowarding.php on the modem, with Tomato Firmware it is super simple to forward.
View 13 Replies View RelatedI've got a pretty simple setup where port forwarding was working without a hitch.My old router (wrt54g) was forwarding RDP requests (over 3389) to my computer's ip. No problems. Then I switched it out with a WRT160N wireless router (and upgraded firmware), and I just can't seem to make the connection.
I've followed all the simple tutorials, ala:
[URL]
Still no luck...! I've ensured my ip is the one the router is pushing connection attempts to, dropped firewall and filtering... still nothing (I've even tried connecting from within the network, using my computer's name) without any success.
I have a linksys router model#wrt54gt v1 and I can not pull up the router's ip address to change the security settings. I have checked and I have the correct IP address of 192.168.1.1. I can ping the router and everything hooked up to the router is now working correctly. I was having problem with the router losing the internet ip address and having to turn everything off and then back on to connect to the internet. I reset the router and it seems to have corrected that problem but I now can not pull up the router's ip address. I have tried in Internet Explorer and Firefox. I have tried typing thebefore the ip address but it will not pull up. I have read countless posts trying to trouble shoot and figure out what's wrong with it and nothing will work.
View 5 Replies View RelatedI am currently accessing the internet on my home lan with a Linksys wrt54g dd-wrt in bridged client mode (small town wifi to T1 network) with a static IP, but plan to add an additional WildBlue 12mbps satellite connection. What I’d like to do is load share between the two connections with a RV042 dual wan router…. The satellite modem connection to one of the WAN ports and configuring the RV042 as my DHCP server is not a problem, but how I should configure my wrt54g to the dual wan router for load sharing?I suspect a IT professional might understand this intuitively, but I am unsure how to pass through my public address from the Linksys to the RV042 WAN port.
View 2 Replies View RelatedI would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0. 0.0/24)How can I forward different ports to this 3 different private networks with an E2500.In the "Games&Applications" Menu are the first 3 octets of the "to IP-address" are fix and corresponds with the LAN ip address.
View 3 Replies View Relatedhow to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies View RelatedI have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I have a Cisco SG300-20. I have read the documentation and cannot seem to locate the instructions for port forwarding. I need to forward TCP port 8088 to IP address 192.168.14.110 on the switch.
View 5 Replies View RelatedI need to retrieve my password for the linksys router wrt54g
View 1 Replies View RelatedI am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedI attached an Iomego Home Media network hard drive to my Linksys E3000 router (via ethernet cable). Before setting up the remote access on the Iomega, I forwarded the ports that it wanted (443 and 21) to the static IP of the Iomega. I checked to see that they were open using yougetsignal.com and they were both open. After setting up the remote access on the Iomega, the 443 port closed and I cant even get into the "manage storage device" page for the Iomega. Iomega uses TZo for the domain names. They tell me that the association is made between the name and my public IP address. My router is out of warranty since Sept, so Linksys wont give me the time of day. I contacted my ISP and while they block a couple of ports, 443 is not one of them.I've installed the latest firmware (1.0.04 - Build 6). Reset and rebooted numerous times, Port 443 remains closed.
View 8 Replies View RelatedI', trying to open my ports 80 and 37777 and have successfully opened them on my linksys router but behind that I have an at&t modem/router....My questions is how do I find the URL number to access my second router to open the ports on it also?
View 3 Replies View RelatedI am trying to access home security camera from outslide my house.I have an AT&T internet coming into the house. They have a router that comes into the house and that splits off to another router in my house which carriers CAT5 all over the house. One of the wires go to another router that I use for my wireless devices.One of those wireless devices is an security camera.Here is my question. I want to view the camera from the internet outside the house. I have followed the instructions given by the manufacture for port forwarding. I have port forwarded the wireless router since the camera is connected to it. Is that wrong since the DSL is coming in one router and then going to another and then to the wireless
View 2 Replies View RelatedI have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking ****, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
I am trying to port forward for Vuze and I am having a problem understanding the concepts at [URL] for working within two routers. I have a Zoom 5241 cable modem connected through a Motorola VT2442-VD for Vonage VOIP, then connected through my Netgear RangeMax WPN824v3 wireless router, to my computer. I am also running AVG internet security. Here is a look at my ipconfig /all:
C:Users
ex>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : MarekFamily
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code]....
However, I do not understand where to setup the static ips and where to drop DHCP to be able to port forward successfully. I have tried in Vuze to set up acceptable ports 51600 for TCP and UDP, but they continue to get this error: "NAT Error - Connect attempt to 67.60.124.173:51600 (your computer) timed out after 20 seconds. This means your port is probably closed." I do know that the Ip present is from my Vonage with my external IP address. I even tried to establish rules for TCP and UDP within AVG Firewall settings for the Vuze program.
I have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch. Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP. I would like to reach the switch remotely. I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work. Should I not be able to Port Forward to the switch across VLAN 1?
View 3 Replies View RelatedI need to set up port forwarding to access a security camera from my home computer. I can't get it to work on my F5D8230-4.
View 8 Replies View Relatedhow do i do port forwarding on my belkin n750 db i want to view my cams when not home i can view on my network not tmobile?
View 3 Replies View RelatedPort forwarding on rv120 does not work. I have followed the workaround instructions: so i have created a firewall access rule on incoming port 21 to an internal ip address on the same port. The router has created the forwarding port rule. But port forwarding does not work. I have tried to use a custom service but nothing!
The router is reachable from wan, I can access via DNS the configuration page and I can ping the router on wan port.
Currently I have the RV042 router working in a dual WAN set up, it is configured to accept connections on numbers of ports like 80,443, 25 and forward them to a local ip.
The problem is this only works with WAN1. Is it even possible to forward ports for connections coming in over WAN2?
I just got a new rv120w and want to set it up, like my old router. I have a webserver that people around the world, should be able to visit, but I can't figure whats wrong. You can see my settings in port forwarding here.
View 4 Replies View Related