Netgear WGT624v3 / Cannot Access The Internet
Sep 4, 2011
yesterday I had switched between my two wireless routers, I went from my Linksys WRTU54G-TM back to my Netgear WGT624v3 because I read that the Netgear provided better range and a bit better speed. I understand that this could be the problem but when I tried to swap out to the Linksys, during the setup, it claims that I have no running internet. The modem is fine, I hooked it straight to my laptop AND my desktop. Now the problem is, I have my desktop and my Xbox 360 connected into the LAN ports, I can connect with my phone and my iTouch wirelessly. My laptop I'm afraid will connect but will not associate with the internet and therefore I cannot access the internet. The Router is a G router and the laptop has a standard wireless g adapter built in.
View 19 Replies
ADVERTISEMENT
Sep 2, 2012
i bought the netgear wgr614v10 router yesterday from yesterday i was trying to connect to wifi but i could setup
View 3 Replies
View Related
Mar 3, 2012
My old router (a dlink dir-615) works just fine, but I figured I would upgrade and try to run OpenWRT or DD-WRT so that I could have one VPN for all my devices.
Anyway, I took the router out and followed the instructions (power off modem for at least 1 minute, connect modem to router, router to computer via ethernet, turn on modem first, wait for it to fully boot up, turn on router, wait for it to fully boot up, and then run the setup on routerlogin.net. The router is currently setup and I can connect my computer or iphone to it just fine, but I cannot access the internet. It doesn't make a difference whether I'm connected via ethernet or wifi. Either way, I get a "No Internet Access" message from Windows 7.
I've tried turning everything off and starting again. No luck. When I go back to my dlink router, everything works fine again.
So, in short:
Modem + ethernet = internet
Modem + Netgear router + ethernet = no internet
Modem + Netgear router + wifi = no internet
Modem + Dlink router (wifi...haven't tried ethernet) = internet
View 8 Replies
View Related
Oct 11, 2012
My laptop says i am connected to the netgear but i am unable to access the internet-
View 1 Replies
View Related
Oct 10, 2011
I got 3 windows 7 pc's at home. IP V6 and IP 4 are enabled. I setup my wireless system and it worked 100%. After 3 months I add a LAN cable to two of my PC's. This is when it all started. My internet browsing became very very slow. When i shutdown the one machine it become fast again. I did the following. Pulled the LAN cable and it was still slow. I then put the cable back and disabled the Wi-Fi and it still was very slow. I rested the defaults and restored my old backup and it still slow. Now I can get any access to the internet any more. I the disconnected the netgear router and take a cheap router with only LAN ports and it work 100%. All the above i did with many router and server reboots.
View 1 Replies
View Related
Feb 18, 2011
Out of no where today, my wireless connection has begun saying "No internet access" and I can't go anywhere online Ever since it began happening, it's been saying that for longer amounts of time. So at first it was only a few seconds, now it's been taking a minute until I re-gain internet access. I haven't installed anything or ran any executables lately, don't have any viruses, I obtain my DNS and IP addresses automatically, and a few minutes ago I installed the newest firmware update of my router and I'm still losing internet. I have a NetGear WNDR3400 router.
View 14 Replies
View Related
Dec 12, 2012
I have a Netgear N600 connected to a modem. I want to connect a switch to the Netgear N600, my question is, will multiple computers connected to the SWITCH have access to the internet?
Router : Netgear N600 [URL]
Switch: Rosewill RC-405X 10/100Mbps Switch [URL]
View 4 Replies
View Related
Nov 4, 2011
My desktop was connected to wireless router by ethernet cable but it seems the ports on the router are now US. Bought netgear N300 USB adapter and installed. Had problems getting "limited connectivity etc" messages 'cos wasn't getting IP address allocated. Have now manually allocated IP address and connection status is now "Connected" (with no warning about limited connectivity etc). However I can't connect to the internet.
View 12 Replies
View Related
Jun 3, 2012
Tried to set up with my AT&T dsl moden. Cannot access internet when everything is connected. At&t says they do not support Netgear, so they couldnt facilitate. They sell Netgear on their website.
View 1 Replies
View Related
Jul 2, 2012
My netgear wireless router (wgr614v9) wont reboot or let me access the internet what should i do.
View 2 Replies
View Related
Aug 20, 2012
Have two other computers that connect with ease to the Netgear wireless router, but the new computer will not access the internet. I have been searching for answers and have tried about everything I can find nuder similar posts, but I still have not internet access. At varying times, I have had "internet access", but no actual ability to load websites. Right now, I do not even have access. I am at a loss.Even at my low level of experience, I am usually able to tinker until I fix the problem, but I am about four hours in and currently seem to have taken a step backward. I cannot even begin to explain what things I have already tried
View 9 Replies
View Related
Dec 5, 2011
I replaced a Netgear router with a similar Netgear router, but the LAN is no longer working.The old Netgear router would drop internet, but LAN would work. Replaced it, the new Netgear router works fine with the internet (cable modem), but the LAN with two computers will not work. The desktop with Windows XP, and a laptop with Windows 7. After runing network setups on both computers several times, I have been unable to reestablish the LAN, however internet access via the router is working. Reinstalled the old router and the LAN works fine, allowing file and printer sharing. Old router is a Netgear WGR614v2, new router is a Netgear WNR2000how to reconfigure the router/computers to get the LAN working again with new router.
View 8 Replies
View Related
Jul 9, 2012
I've got a windows server 2003 machine which access internet over a Netgear N150 router also I've got an static IP, now internet is working properly even I can ping my machine from a remote machine.Here starts the real problem, I've shared few folders which I can't access from any remote machine not in my LAN.Although I could access my server through remote desktop and everything else is working fine, I've opened port 445 on router even that didn't worked also Windows firewall is OFF.Now when I try to browse my server through \myserverip it shows me a blank window but when I tried to access it like:
\myserveripsharedfolder it gives me error which reads something like
"File and printer sharing seems online but server is not responding on port 445."
View 10 Replies
View Related
Dec 6, 2012
I have 3 computers wired to a Netgear R6300. Two of those computers (both running XP SP 3) I added new LAN Gigabit Cards (Tenda TEL9901G) . One recognized the card right away and had no issue connecting to the Internet (using this computer now). The other shows a 1.0 Gbps connection but I can not get any web pages to come up. I can access other computers and devices on the network without an issue on the computer that doesn't connect to the Internet.
If I type in the web address it says "Server Not Found." If I type in the IP address it will come up with the name of the site in the address bar but it still says "Server Not Found." I've tried several times to unplug the router and modem (Motorola Surfboard) and restart everything but the problem was still there. Also, I tried other Ethernet cables and no change. The LAN card drivers are up to date but I don't think the card is the issue since I swapped the new cards (to see if the card was the problem) and it does show a 1.0 Gbps connection. Also, tried uninstall/reinstall, disable/enable the card many times.I didn't change any setting in the router after installing the cards.Here is the ipconfig output:
Windows IP Configuration
Host Name . . . . . . . . . . . . : GATEWAY
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Mixed
IP Routing Enabled. . . . . . . . : Yes
WINS Proxy Enabled. . . . . . . . : No[code]......
View 6 Replies
View Related
Aug 25, 2012
My Dell Laptop is unable to access internet through my Netgear wireless router. Other equipment (Lenovo laptop, ipad, iphone, PS3) accessing internet fine through same router. I ran the onboard Dell Wireless WLAN Card Utility. Hardware diagonistics all pass. Connection diagnostics reports:
Radio Passed
Association Passed
Authentication Passed
Local IP Address Passed
[code]....
View 1 Replies
View Related
Jul 24, 2012
I have the Netgear wndr4500 router setup as an AP. The wndr4500 has a feature for guest wifi but will not connect to the internet. The main wifi will connect to the internet fine. I'm wondering if I use the WNDR4500 as an AP, the guest features do not work?
View 2 Replies
View Related
Mar 23, 2011
Every day for the past week my Internet access goes down. I have a netgear router connected to Comcast modem. I have to reset the modem then the router constantly and it gets irritating. I called comcast and they say reset them. But why should I have to constantly reset.... Sometimes I just ignore it and it comes back up later... what is going on??
View 1 Replies
View Related
Apr 13, 2013
I just bought a Netgear Router WNR 2000 v3 and installed it. I got inside the router and could set up a Network Name and security key. However, I can not access the internet when I chose a security password using WPA 2, WPA-PSK + WPA 2 PSK, or WPA/WPA 2. It only accesses the internet when I chose None.( no secured ).At this time, my network is unsecured because there isn't way I can access the internet when I create a security key using the 3 options the router offers.
Note : I have tried the 3 security options creating a key number and my computer connect to the wireless network but don't access the internet. It only access the internet when I select None ( no secured )
View 2 Replies
View Related
Apr 7, 2011
I cannot access the setup page, even without the modem connected to the router, even after pushing reset button. It says I have limited access both to the wireless and to the wired connections, but won't let me access the internet (via the separate modem)I can access the internet via the modem fine
View 2 Replies
View Related
Dec 23, 2012
have netgear pcmcia card need to connect to new belkin wireless access point.
View 1 Replies
View Related
Oct 6, 2011
setting up my NETGEAR Wireless-N Access Point. I am a novice, sales person told me it was plug and play...
View 1 Replies
View Related
Jan 10, 2013
I have a Virgin Media Netgear VMDG480 broadband modem/router. Whilst the Ethernet performance is strong the Wifi signal strength is weak and only provides signal to half of my house. I've seen various comments on other forums that this is a common problem for this device. To overcome this I propose to install a Wireless Access Point at the far end of the house and connect this to the VMDG480 via powerlink. (I already use this powerlink connect to a PC at the far side of the house and this works really well.)
My concerns are:
1. Will the VMDG480 recognise the Wireless Access Point? I've seen some comments that suggest that this may be a problem.
2. Is there any specific type of Wireless Access Point that I should use to ensure compatibility with the VMDG480?
3. Is the use of a Wireless Access Point across powerlink a sensible approach?
4. An alternative approach is to use a Wireless Range Extender. Is this a better approach? If yes should I use a Netgear device to ensure compatibility?
View 3 Replies
View Related
Dec 31, 2011
I have tried to set up a wireless access point using an old Netgear DG384G router as the access point. This is connected by wire to a Buffalo WBMR-G54 wireless router.I have switched off DHCP and set a static IP of 198.168.11.99 on the netgear and it is using WPA-PSK security. Buffalo is on channel 6 and on WEP, Netgear channel 11.All was working fine, could connect on laptop, Ipad and iphone all working ok and then suddenly at about 6.00PM the connection became very slow (Last 2 Nights)Tried rebboting router, switched off security and no difference.
View 3 Replies
View Related
Apr 18, 2012
I have an AT&T 2Wire Router/Modem and want to convert my Netgear WNDR370 to an Access Point.
View 1 Replies
View Related
Jun 2, 2011
I have been unable to access my WHS when I recently traveled across the US. I have a Netgear WNDR3700 router. My DSL modem is a DSL-520B. I have AT&T DSL (6 Mbs). I have tried enabling and disabling "remote management", forwarding to ports 80, 443, 3390, and 4125 all with no success.Also, I believe (correct me if I am wrong) the remote management address is incorrectly listed as http://192.168.1.2:8080. I have also turned off USB storage in case of a possible conflict I have read about with port 80.
View 4 Replies
View Related
Jan 9, 2012
I have a router TP-Link (without wireless) connected in my modem wich have this subnet : 192.168.0.*, that work fine. But I need a wireless connection too, my wireless router had this ip given by the TP-Link router: 192.168.0.13.
I have a NETGEAR WIRELESS-G ROUTER WGR614 which gain 192.168.0.13 but I need that gives ip's in the same subnet that TP link router. If the person connect to my wi-fi it should receive an ip like 192.168.0.*, I already try to disable the DHCP server in the NETGEAR but it's not working too. How can I do that ?
View 2 Replies
View Related
Jun 3, 2011
I am trying to wirelessly connect a netgear wgr614 v6 to be used as an accesspoint and my router connected to the cable modem is a dlink dir825
View 1 Replies
View Related
Sep 29, 2012
Here is my setup:
Netgear WNR2000 router.
Macbook Pro with Snow Leopard connected to router through wireless.
Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
View 8 Replies
View Related
Feb 23, 2011
I have a weird problem with my network setup. I have a netgear DG834GT ADSL router which runs fine with my Belkin 51B64C wireless router but when I enable "Use as Access Point" in order for me to see my wireless laptops connected to it the internet performance goes bad, the traffic cuts out momentarily for about 7 seconds at a time, its pretty difficult to surf the net having to wait.The setup is as follows:
Netgear
Gateway IP: 10.0.0.1
Subnet Msk: 255.255.255.0
DHCP Enabled
Belkin
Gateway IP: 10.0.0.9
Subnet Msk: 255.255.255.0
DHCP Enabled
as I said above the reason I enable "Use As Access Point" is so I can see the devices in Explorer for file sharing. Is there a way I can use port forwarding on the router to see the devices it would solve the performance problem.
View 15 Replies
View Related
May 30, 2012
I tried to use my Netgear 614 router to my Netgear 3300 as an access point to gain range. But now I think I've screwed up the IP address(s) and have lost my wifi ability.
View 7 Replies
View Related
Dec 9, 2011
I need to setup my Netgear as a switch/access point. I need the following set-up. My ipconfig /all reports:
View 27 Replies
View Related
Feb 23, 2011
can i use a netgear wg602 access point to connect my xbox 360 to my home network.
View 1 Replies
View Related
Jul 11, 2011
I have a NETGEAR Wireless-N 150 Router WNR1000 v2. I am trying to configure it for my LAN which has a DIALER. [code] I tried to configure my NG but it is unable to connect to the network on its own. I have to use CONNECT dialer from my PC to connect which is useless because I can't use my wi-fi enabled devices to access network.
View 1 Replies
View Related
