Using Netgear WGR614 Router As Switch? (Wi-Fi Access)
Jan 9, 2012
I have a router TP-Link (without wireless) connected in my modem wich have this subnet : 192.168.0.*, that work fine. But I need a wireless connection too, my wireless router had this ip given by the TP-Link router: 192.168.0.13.
I have a NETGEAR WIRELESS-G ROUTER WGR614 which gain 192.168.0.13 but I need that gives ip's in the same subnet that TP link router. If the person connect to my wi-fi it should receive an ip like 192.168.0.*, I already try to disable the DHCP server in the NETGEAR but it's not working too. How can I do that ?
I have a prob with my laptops,wireless setup although it shows wlan on it will not work without a connection to the router,netgear wgr614,I have gone into Devise Mng and found the following faults,Serial cable IRDA problem code 43 & SRTSPX code 24 not working.
Can't get into my netgear router to config it. I have tried using 192.168.0.1 and 192.168.1.1. So far it will not give me a window to log in. It has allways work before on xp pro, but now i am using win 7 on my new computer.
i am trying to connect my netgear wgr614 v7 wireless router and i can't do it. i have the actiontec m1000 modem which is thru qwest i have read the setup manual available online on how to setup the modem with the router but it just doesnt do anything?
I need to replace my Netgear WGR614 v6 router which is a good 4 or 5 years old, and i think is the cause of a very slow internet connection. Download speeds are reaching 1.1mb/s but browsing on the internet is unbelievably slow and fails to load pages most of the time saying the DNS look-up failed. I was thinking of purchasing the Buffalo Wireless-N300 Cable Router. I'm with Virgin Media, i think on 10meg broadband. I think it will support moving from wireless G to wireless N, but my laptop is fairly old too - Fujitsu Siemens Lifebook C series.
I just added a wireless router netgear wgr614 and I secured it and it worked for one day and then after that no internet connection. I've rest and unplugged both the modem and the router and still nothing.
I have a Netgear WGR614 wireless router connected to my WOW DSL modem and utilize WPA as security. wireless signal is good on first floor but drops significantly in my basement. I have a Netgear WG102 AP I would like to configure as a repeater and place in my basement to boost the WGR614 signal strength. What configurations must I apply to both or either devices to achieve this setup?
I'm connected through the router, a few times a day I cannot open web pages, getting error: Error 105 (net::ERR_NAME_NOT_RESOLVED): Unable to resolve the server's DNS address.Skype continues to work. Here are the results of pinging:
Quote:
Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:UsersSri Guru>ipconfig /all[code]....
One technician said that this is the providers problem, but I don't think so. When I restart the modem everything works.I have a Netgear WGR614 v9 router.I use ESET 5 security. Btw, connection drops on all computers connected through the router, so it's not my firewall.
I bought a tp-link WA701ND and a netgear WGR614. i wish to pick up signal using 701 and then let 614 repeat it. no more tech support coz im already broke.
My primary home wireless is a Linksys WRT54GS Broadband Router. I have an older Netgear WGR614 Wireless Router that I would like to setup as a wireless bridge to use in another room to connect my other electronics to (i.e tv, blu-ray, Wii).
At my office we have a simple network using a Netgear WGR614 V7 router. 4 XP machines are connected via Ethernet cable and three other people are connected wirelessly (one XP laptop, one Win7 laptop and one Win 7 netbook). It appears that whenever the netbook is on the network, the other two laptops lose connectivity. The wired machines are fine. Power cycling the router and rebooting usually solves the problem.
I've two routers, one which i got from BSNL when opted for internet connection. Its a Utstartcom Type II wireless modem and the other which i got from a friend is Netgear WGR614 wireless modem/router.Now coming to the real picture. I've the BSNL wireless modem connected and working perfectly on the 3rd floor on one PC, but NOT configured for wireless access and i've another PC on Ground Floor where i need an internet connection. Fortunately, i got a router/modem which is Netgear WGR614. I do not want a wired connection between these two PCs then wanted to try the wireless way?
I couldn't connect wirelessly to my NETGEAR router because of the "DNS server isn't responding" error.I then eventually made the rather dumb mistake of doing a factory reset, so now the router isn't even in range apparently Therefore I connected to the router with a wired connection and after a "Investigate router or broadband modem issues" error I eventually came to the error in the title.Currently I'm connected directly via my virgin modem with a wired connection, so this is my means of creating this thread.
Below is what i got from ipconfig /all using a wired connection to my router.
Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:Userschenupan>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : CGPC Primary Dns Suffix . . . . . . . :
I have a Netgear N600 connected to a modem. I want to connect a switch to the Netgear N600, my question is, will multiple computers connected to the SWITCH have access to the internet?
I have a Netgear wireless router(WGR614 v9) and im trying to connect a second laptop to it. The laptop is accessing the internet when I have it connected to my modem via Cat 5 Patch cable.When I detach the cable from the laptop and modem, it doesn't connect to the internet. I went through the whole installing with the cd that comes with the router but after I finish I get the same results.
According to System properties:
Microsoft Windows XP (theres a sticker on my laptop for Windows Vista) Home Edition Version 2002 Service Pack 3
Posted below is my computer info from using ipconfig.
I have a wgr614 V6 router, yes its old. I had 3 devices connected to it just fine before without any issues. But now It only allows my laptop, when I try to connect with my ipod touch or desktop, not only does it fail, the entire network crashes and my laptop loses it and its gone. It then takes about 2 minutes to come back up. So whenever I attempt to connect with another device the network crashes. so right now only my laptop is connected.I downloaded & updated to the newest firmware, did not work.I tried resetting the router, and made the network all over again, did NOT work.
I recently bought a Netgear switch in order to hook up to wired PCs to my modem. I also have a ASUS n53 wireless router that I am trying to connect to the switch. The problem is I can't seem to get internet access to the wireless router I have tried setting it up as an access point, I have tried disabling the DHCP on it.
So my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
Out of no where today, my wireless connection has begun saying "No internet access" and I can't go anywhere online Ever since it began happening, it's been saying that for longer amounts of time. So at first it was only a few seconds, now it's been taking a minute until I re-gain internet access. I haven't installed anything or ran any executables lately, don't have any viruses, I obtain my DNS and IP addresses automatically, and a few minutes ago I installed the newest firmware update of my router and I'm still losing internet. I have a NetGear WNDR3400 router.
Netgear WNR2000 router. Macbook Pro with Snow Leopard connected to router through wireless. Windows 7 Desktop getting internet through the MBP ethernet.
I can't figure out how to be a part of my "Home Network" with my Win7 Machine so I can see other computers in my house, use my networked printers, etc. I can only see the MBP it is connected to in network panel. I want to be able to stream the movies on this computer to my iPad which is connected to the wireless router.
I have a weird problem with my network setup. I have a netgear DG834GT ADSL router which runs fine with my Belkin 51B64C wireless router but when I enable "Use as Access Point" in order for me to see my wireless laptops connected to it the internet performance goes bad, the traffic cuts out momentarily for about 7 seconds at a time, its pretty difficult to surf the net having to wait.The setup is as follows:
as I said above the reason I enable "Use As Access Point" is so I can see the devices in Explorer for file sharing. Is there a way I can use port forwarding on the router to see the devices it would solve the performance problem.
I tried to use my Netgear 614 router to my Netgear 3300 as an access point to gain range. But now I think I've screwed up the IP address(s) and have lost my wifi ability.
I have a NETGEAR Wireless-N 150 Router WNR1000 v2. I am trying to configure it for my LAN which has a DIALER. [code] I tried to configure my NG but it is unable to connect to the network on its own. I have to use CONNECT dialer from my PC to connect which is useless because I can't use my wi-fi enabled devices to access network.
Have two other computers that connect with ease to the Netgear wireless router, but the new computer will not access the internet. I have been searching for answers and have tried about everything I can find nuder similar posts, but I still have not internet access. At varying times, I have had "internet access", but no actual ability to load websites. Right now, I do not even have access. I am at a loss.Even at my low level of experience, I am usually able to tinker until I fix the problem, but I am about four hours in and currently seem to have taken a step backward. I cannot even begin to explain what things I have already tried
I replaced a Netgear router with a similar Netgear router, but the LAN is no longer working.The old Netgear router would drop internet, but LAN would work. Replaced it, the new Netgear router works fine with the internet (cable modem), but the LAN with two computers will not work. The desktop with Windows XP, and a laptop with Windows 7. After runing network setups on both computers several times, I have been unable to reestablish the LAN, however internet access via the router is working. Reinstalled the old router and the LAN works fine, allowing file and printer sharing. Old router is a Netgear WGR614v2, new router is a Netgear WNR2000how to reconfigure the router/computers to get the LAN working again with new router.
I've got a windows server 2003 machine which access internet over a Netgear N150 router also I've got an static IP, now internet is working properly even I can ping my machine from a remote machine.Here starts the real problem, I've shared few folders which I can't access from any remote machine not in my LAN.Although I could access my server through remote desktop and everything else is working fine, I've opened port 445 on router even that didn't worked also Windows firewall is OFF.Now when I try to browse my server through \myserverip it shows me a blank window but when I tried to access it like:
\myserveripsharedfolder it gives me error which reads something like
"File and printer sharing seems online but server is not responding on port 445."
I recently put in a Netgear firewall, configured it, its running no problem. Then I setup a new Netgear N600 wireless router, configured it, gave it a static IP, connected to it, works like a charm. Thing is, when I try to access the web gui I receive nothing.. Is the Netgear firewall taking priority or something? I went directly connected to the netgear wifi router and double checked to make sure that there was no settings restricting administration from wifi users, etc..
i currently have a netgear wgr614v9 running the most recent firmware update and a tplink nr741nd running the latest dd wrt firmware.the netgear is my main router connected to the modem positioned in the living room attached to this is a wired ps3, wii and various laptops connect wirelessly to this. In my bedroom i have the tplink router is is setup as a client on the netgear router allowing media network drive access to the internet.
What i would like to achive is to be able to connect to the netgear router wirelessly and have access to the network drive attached to tplink router.I have tried a client bridge on the dd wrt firmware but this does not work at all. I have read that i need to setup a VPN on the dd wrt but i can find anything on how to do this when trying to access a drive on a second level.
I have a Netgear N300 and am using a linksys wrtg54g flashed with dd-wrt as an extender. I would like to setup my wireless network to limit various devices (laptops, iPod touch, etc) to certain times of the day.
How do I configure both devices to limit connectivity? I've got it down pretty much on the NetGear using a MAC address filter and scheduling the services, but I am not sure how to get the extender to do the same.
How do I setup Netgear WNR2000v2 wireless router as a wireless access point? I just upgraded to a Netgear WNDR3700 wireless router and I don't wanted the wnr2000 to go waste. So basically as the followings: