Can't get into my netgear router to config it. I have tried using 192.168.0.1 and 192.168.1.1. So far it will not give me a window to log in. It has allways work before on xp pro, but now i am using win 7 on my new computer.
p.s. the router is a Netgear model # WGR614
I have a Netgear WGR614 wireless router connected to my WOW DSL modem and utilize WPA as security. wireless signal is good on first floor but drops significantly in my basement. I have a Netgear WG102 AP I would like to configure as a repeater and place in my basement to boost the WGR614 signal strength. What configurations must I apply to both or either devices to achieve this setup?
View 3 Replies View RelatedI've two routers, one which i got from BSNL when opted for internet connection. Its a Utstartcom Type II wireless modem and the other which i got from a friend is Netgear WGR614 wireless modem/router.Now coming to the real picture. I've the BSNL wireless modem connected and working perfectly on the 3rd floor on one PC, but NOT configured for wireless access and i've another PC on Ground Floor where i need an internet connection. Fortunately, i got a router/modem which is Netgear WGR614. I do not want a wired connection between these two PCs then wanted to try the wireless way?
View 1 Replies View RelatedI have a prob with my laptops,wireless setup although it shows wlan on it will not work without a connection to the router,netgear wgr614,I have gone into Devise Mng and found the following faults,Serial cable IRDA problem code 43 & SRTSPX code 24 not working.
View 1 Replies View Relatedi am trying to connect my netgear wgr614 v7 wireless router and i can't do it. i have the actiontec m1000 modem which is thru qwest i have read the setup manual available online on how to setup the modem with the router but it just doesnt do anything?
View 2 Replies View RelatedI need to replace my Netgear WGR614 v6 router which is a good 4 or 5 years old, and i think is the cause of a very slow internet connection. Download speeds are reaching 1.1mb/s but browsing on the internet is unbelievably slow and fails to load pages most of the time saying the DNS look-up failed. I was thinking of purchasing the Buffalo Wireless-N300 Cable Router. I'm with Virgin Media, i think on 10meg broadband. I think it will support moving from wireless G to wireless N, but my laptop is fairly old too - Fujitsu Siemens Lifebook C series.
View 10 Replies View RelatedI have a router TP-Link (without wireless) connected in my modem wich have this subnet : 192.168.0.*, that work fine. But I need a wireless connection too, my wireless router had this ip given by the TP-Link router: 192.168.0.13.
I have a NETGEAR WIRELESS-G ROUTER WGR614 which gain 192.168.0.13 but I need that gives ip's in the same subnet that TP link router. If the person connect to my wi-fi it should receive an ip like 192.168.0.*, I already try to disable the DHCP server in the NETGEAR but it's not working too. How can I do that ?
I just added a wireless router netgear wgr614 and I secured it and it worked for one day and then after that no internet connection. I've rest and unplugged both the modem and the router and still nothing.
View 1 Replies View RelatedI'm connected through the router, a few times a day I cannot open web pages, getting error: Error 105 (net::ERR_NAME_NOT_RESOLVED): Unable to resolve the server's DNS address.Skype continues to work. Here are the results of pinging:
Quote:
Microsoft Windows [Version 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:UsersSri Guru>ipconfig /all[code]....
One technician said that this is the providers problem, but I don't think so. When I restart the modem everything works.I have a Netgear WGR614 v9 router.I use ESET 5 security. Btw, connection drops on all computers connected through the router, so it's not my firewall.
I bought a tp-link WA701ND and a netgear WGR614. i wish to pick up signal using 701 and then let 614 repeat it. no more tech support coz im already broke.
View 1 Replies View RelatedMy primary home wireless is a Linksys WRT54GS Broadband Router. I have an older Netgear WGR614 Wireless Router that I would like to setup as a wireless bridge to use in another room to connect my other electronics to (i.e tv, blu-ray, Wii).
View 3 Replies View RelatedI am trying to wirelessly connect a netgear wgr614 v6 to be used as an accesspoint and my router connected to the cable modem is a dlink dir825
View 1 Replies View RelatedAt my office we have a simple network using a Netgear WGR614 V7 router. 4 XP machines are connected via Ethernet cable and three other people are connected wirelessly (one XP laptop, one Win7 laptop and one Win 7 netbook). It appears that whenever the netbook is on the network, the other two laptops lose connectivity. The wired machines are fine. Power cycling the router and rebooting usually solves the problem.
View 3 Replies View RelatedI couldn't connect wirelessly to my NETGEAR router because of the "DNS server isn't responding" error.I then eventually made the rather dumb mistake of doing a factory reset, so now the router isn't even in range apparently Therefore I connected to the router with a wired connection and after a "Investigate router or broadband modem issues" error I eventually came to the error in the title.Currently I'm connected directly via my virgin modem with a wired connection, so this is my means of creating this thread.
Below is what i got from ipconfig /all using a wired connection to my router.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:Userschenupan>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : CGPC
Primary Dns Suffix . . . . . . . :
[code]....
How do i configure my netgear router to my samsung blu-ray player to allow wireless connection?
View 2 Replies View RelatedI have a Netgear wireless router(WGR614 v9) and im trying to connect a second laptop to it. The laptop is accessing the internet when I have it connected to my modem via Cat 5 Patch cable.When I detach the cable from the laptop and modem, it doesn't connect to the internet. I went through the whole installing with the cd that comes with the router but after I finish I get the same results.
According to System properties:
Microsoft Windows XP (theres a sticker on my laptop for Windows Vista)
Home Edition
Version 2002
Service Pack 3
Posted below is my computer info from using ipconfig.
Windows IP Configuration
Host Name . . . . . . . . . . . . : ******
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
I have a wgr614 V6 router, yes its old. I had 3 devices connected to it just fine before without any issues. But now It only allows my laptop, when I try to connect with my ipod touch or desktop, not only does it fail, the entire network crashes and my laptop loses it and its gone. It then takes about 2 minutes to come back up. So whenever I attempt to connect with another device the network crashes. so right now only my laptop is connected.I downloaded & updated to the newest firmware, did not work.I tried resetting the router, and made the network all over again, did NOT work.
View 7 Replies View Relatedi am unable to configure my netgear router with my clear modem
View 1 Replies View RelatedIn order to feed my netgear dgn1000 adsl modem/router with a rca roadrunner modem with ethernet single jack do I enable NAT or not on Netgear router and do I use router as DHCP or not?
View 2 Replies View RelatedI think it should be possible to create an IPSec tunnel between a Netgear FVS336Gv2 firewall/router and AWS VPC however, I've been unable after several tries. How do I setup a connection for a Amazon VPC?
View 1 Replies View RelatedHow is it possible to configure 2 VLANs to communicate with each other on the same switch? I have managed to create 2 VLANS and they both work (and can access the internet), but they can't communicate with each other.VLAN1 has an IP range starting 10.4.160 and VLAN2 has an IP range starting 10.6.192.Is it VLAN routing that I'm looking for?
View 1 Replies View RelatedI am using a netgear wgr614 router and the laptop I'm trying to use won't connect. It shows up as available but 'Windows was unable to connect to NETGEAR' pops up. Futher troubleshooting brings up "Investigate router or access point issues" but turning off the router did not fix the problem.
This is what is on my Desktop:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsDebra>ipconfig
[Code].....
I have about a Netgear WGR614 router and a few CentreCom FS708 switches.Is there a way to create a home network so every safe an secure computer can access the internet and another network where I would fix machines that have virus's or machines that I don't want to access the home network.
How would I go about doing this? Or do I need a better router with DD-WRT installed on it?
How do I configure and set up my desktop to get on my neighbors internet connection with the netgear wireless adapter.
View 3 Replies View Relatedhow to transfer files from Desktop (XP) to Laptop (XP). I am using a Netgear Wireless G router WGR614 v9
View 1 Replies View RelatedI have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
View 7 Replies View RelatedI have a netgear VMDG280 router and my girlfriend has a DS.. her dumb DS doesn't understand any protocol apart None and WEP apparently..She has to go online with her DS to get some mystery gift on pokemon.. I am too old for this I swear. I poked around the settings but the Router appears to have come pre-configured and I cannot find any setting in the router admin panel to disable security.
View 1 Replies View Relatedwhen i click on connect to network nothing happens. it doesn't do anything, but if i plug in my old router it will connect just fine. It's just the new router
View 1 Replies View RelatedI pressed the reset button on my netgear router (WGR614 v7) and now the wireless light will not go on and i can't connect to it because I don't have a ethernet cable.
View 2 Replies View RelatedI have a DVR connected to CCTV cameras that I would like to connect to my computer via Ethernet and a Netgear N150 router which also handles my broadband. A program called VideoViewer is installed on the computer which works with the DVR to view images on the computer via ethernet.it works with a Zoom router, but not the Netgear.
View 3 Replies View RelatedWhen I first got my Netgear N-150 router, the wireless speed on it was great. However several days passed and I started to notice the speed was decreasing; because I have HughesNet (I hate it) I thought this was the ISP's fault and called them and they said my speed had not gone down. During the day, the signal is fine and is at full bars and the speeds are OK. During the evening/night hours the connection becomes faulty and the laptop will disconnect from the network altogether. If I plug the ethernet cable directly into the router, the speed is OK also. I have taken the security off the connection to see if it will make any difference; it doesn't. I don't know if I need to buy a new router or what. I know my way around computers and routers (not entirely though) and I cannot figure it out. I have 2 laptops with Windows Vista both with home Premium.
View 11 Replies View RelatedI need to set a password for my netgear router. It gave me the user name already.
View 1 Replies View Relatedi have a netgear n150 router and the lock light is on.
View 1 Replies View Related