I think it should be possible to create an IPSec tunnel between a Netgear FVS336Gv2 firewall/router and AWS VPC however, I've been unable after several tries. How do I setup a connection for a Amazon VPC?
View 1 RepliesI need to replace my old sonicwall firewall. I was looking at the latest Sonicwalls, but they are really expensive if you get all of the services. For the TZ 210 - if I go for just the firmware updates without the gateway security services, how much better of a firewall is it than a Netgear fvs336g?
View 3 Replies View RelatedDownload speeds, per speedtest.net and speakeasy, are about 20mbps.When the speed test gets to the upload part, it usually hangs or takes a long time before giving me a result of about 0.04mbps. Basically, it's so slow, it sometimes just gives up and times out.This translates into a real shoddy internet experience because something as simple as choosing airline tickets requires your computer to "upload" your choices. And of course, if that doesn't happen within a certain amount of time... Timeout! I have tested the connection without my Netgear FVS336G Dual WAN router in the way and it is much better so I'm certain it's the router.When I tell the router to use WAN 2, which is where my AT&T DSL connection is on, the upload works just fine (about .4 mbps - I'm provisioned at 512kbps so it's fine).Also, this is the case on ALL computers on the network - wired, wireless, PC, Mac, iPhone, iPad, you name it. So, it's definitely not device specific.
View 1 Replies View RelatedSamsung will be releasing the Galaxy Note 8 sometime in the second quarter of this year.
I have an Amazon Prime Account and would like to know if I can transfer the downloaded movies I purchase on Amazon on the Galaxy Note 8.
I have Windows 8 installed on my computer at home.
We are in the process of setting up an Amazon S3 network backup of the NAS server we have in our office. We are using a Synology NAS to backup to Amazon s3, and we use a Cisco PIX 501 to secure our network. The backup from the NAS to Amazon is going painfully slow, so I contacted Synology to resolve the issue. After they examined everything, they think the router is filtering outbound traffic, and this is causing the upload to slow down. I was told the upload should happen over HTTP and HTTPS, and I made sure these ports where open through the Access Rules. There are no rules defined in the Filter Settings.
I looked at the settings with the PDM, and I can't find where the filtering would be. I'm not too familiar with the PIX or all the network settings involved.
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version :
ISP :
I just bought and installed this wireless router, specifically so that I could use me kindle..but, keep getting rejected due to a password error...the password is correct. On Amazon it looks like there may be a setting that needs adjustment in order to accept the Kindle..
I have an E2000, and I connect wirelessly through my Macbook. When I use the internet on any laptop I connect to the router (not just the Mac) I can't log in to Facebook, Amazon, Ebay, Hotmail, or any other site, and Google image pages only load halfway. In certain websites I try to use I cannot click anything at all. I have tried unplugging and plugging back in, and I have tried resetting the router.
View 1 Replies View RelatedCan't get into my netgear router to config it. I have tried using 192.168.0.1 and 192.168.1.1. So far it will not give me a window to log in. It has allways work before on xp pro, but now i am using win 7 on my new computer.
p.s. the router is a Netgear model # WGR614
How is it possible to configure 2 VLANs to communicate with each other on the same switch? I have managed to create 2 VLANS and they both work (and can access the internet), but they can't communicate with each other.VLAN1 has an IP range starting 10.4.160 and VLAN2 has an IP range starting 10.6.192.Is it VLAN routing that I'm looking for?
View 1 Replies View RelatedHow do i configure my netgear router to my samsung blu-ray player to allow wireless connection?
View 2 Replies View RelatedI've two routers, one which i got from BSNL when opted for internet connection. Its a Utstartcom Type II wireless modem and the other which i got from a friend is Netgear WGR614 wireless modem/router.Now coming to the real picture. I've the BSNL wireless modem connected and working perfectly on the 3rd floor on one PC, but NOT configured for wireless access and i've another PC on Ground Floor where i need an internet connection. Fortunately, i got a router/modem which is Netgear WGR614. I do not want a wired connection between these two PCs then wanted to try the wireless way?
View 1 Replies View RelatedI have a Netgear WGR614 wireless router connected to my WOW DSL modem and utilize WPA as security. wireless signal is good on first floor but drops significantly in my basement. I have a Netgear WG102 AP I would like to configure as a repeater and place in my basement to boost the WGR614 signal strength. What configurations must I apply to both or either devices to achieve this setup?
View 3 Replies View Relatedi am unable to configure my netgear router with my clear modem
View 1 Replies View RelatedHow do I configure and set up my desktop to get on my neighbors internet connection with the netgear wireless adapter.
View 3 Replies View RelatedI have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
View 7 Replies View RelatedIn order to feed my netgear dgn1000 adsl modem/router with a rca roadrunner modem with ethernet single jack do I enable NAT or not on Netgear router and do I use router as DHCP or not?
View 2 Replies View RelatedHow to get into netgear to put security on
View 2 Replies View RelatedI just got a foscam camera. I am trying to be able to connect to it from my phone while I am not home. I am having one hell of a time trying to connect to my router, I haven't been able to yet. I am using port forwarding, have followed all kinds of instructions I found on the web, and none work. I cannot get port 80 to open. I have a net gear wnr2000v2.
View 1 Replies View RelatedI recently reset my router as I did not know my password and I needed to find out what the WEP was. Now the internet light will not come on. I have followed instructions on setting up the router as if it were new and still no luck.
View 3 Replies View RelatedI am hard wiring a Netgear wireless modem DG834G to the LAN connection on my PC. The modem lights up, the internet light flashes then goes green and the connection to the PC is lit. My PC wont see the modem - when I type 192.168.0.1 it cannot access the Netgear setup page. I have tried swapping the cable and even bought a PCI Lan card and installed it but the modem wont work in either port? I've had the modem checked out and it works fine it's just something in my PC stopping it from seeing the Modem. At present I have a USB modem hard wired which works fine. I unplug this when trying to setup the NEtgear modem...
View 6 Replies View RelatedI cannot access the setup page, even without the modem connected to the router, even after pushing reset button. It says I have limited access both to the wireless and to the wired connections, but won't let me access the internet (via the separate modem)I can access the internet via the modem fine
View 2 Replies View RelatedI have a Netgear Wireless USB Adapter (WNA3100) for my PC. The router is in the other room (approx 5-6 meters away) connected to my flatmates laptop. The adapter worked fine for almost two months, but at the past 2 weeks it keeps disconnecting in every 2-15 minutes, for 1-3 minutes. I have Windows 7 and I'm not familiar with networking issues so the only thing I did was to reinstall the driver and update it, but this didn't work.
View 6 Replies View RelatedI posted of an issue we were having but I feel like I was getting ahead of myselfBasically I need to know how to do 2 things.I want to assign a static IP I purchased from Comcast to my Netgear N300 router and then in turn want that IP address to be linked to the server here in our office so that when people use the Remote Desktop Connection it directs them to the proper machine.
View 5 Replies View RelatedI got a new modem from Optus Australia and they sent me this modem netgear ofcourse , and I wanna know what's the best settings for it cause I'm dropping signal from my ps3 (im using wi-fi) and lagging online,
View 9 Replies View RelatedI just need to know what numbers to put in this Server IP AddressI tried putting a 0 and 1 at the end.
View 5 Replies View RelatedI set up my FVS338 netgear firewall to accept vpn client connection, opening the vpnipsec door (UDP 500) either on the router DG834 and the FW.After that i set up an IKE and VPN policy following the netgear wizard.Opened the Shrew VPN access manager and configured all the fields according to NETGEAR FVS338 settings.[CODE]
View 3 Replies View Relatedwhen i click on connect to network nothing happens. it doesn't do anything, but if i plug in my old router it will connect just fine. It's just the new router
View 1 Replies View RelatedI pressed the reset button on my netgear router (WGR614 v7) and now the wireless light will not go on and i can't connect to it because I don't have a ethernet cable.
View 2 Replies View RelatedI have a DVR connected to CCTV cameras that I would like to connect to my computer via Ethernet and a Netgear N150 router which also handles my broadband. A program called VideoViewer is installed on the computer which works with the DVR to view images on the computer via ethernet.it works with a Zoom router, but not the Netgear.
View 3 Replies View RelatedThe first time i had to set dmz i had free tech support from the company. no my free tech support has expired and they want money for tech support now.I would like to know what ip to put in my dmz setting, my ip is supposed to be static, but it changes every few months anyways.I'm aware that having dmz open is a risk, but i have a software firewall.i have my router setup so my 360 and my pc so i need dmz, , if i did not have dmz i would be setting up forward ports for quite some time, as i play multiple pc games.
View 6 Replies View RelatedWhen I first got my Netgear N-150 router, the wireless speed on it was great. However several days passed and I started to notice the speed was decreasing; because I have HughesNet (I hate it) I thought this was the ISP's fault and called them and they said my speed had not gone down. During the day, the signal is fine and is at full bars and the speeds are OK. During the evening/night hours the connection becomes faulty and the laptop will disconnect from the network altogether. If I plug the ethernet cable directly into the router, the speed is OK also. I have taken the security off the connection to see if it will make any difference; it doesn't. I don't know if I need to buy a new router or what. I know my way around computers and routers (not entirely though) and I cannot figure it out. I have 2 laptops with Windows Vista both with home Premium.
View 11 Replies View RelatedI have rebooted my netgear router to the factory settings and now the internet wont work , i have no idea how to get it to work again. On the box all the right lights are green exept the internet light which is red.
View 1 Replies View RelatedNetgear FS605 v3 wont connect to both my ps3 and my pc. It can only get internet to either my pc or my ps3.
View 1 Replies View Related