How is it possible to configure 2 VLANs to communicate with each other on the same switch? I have managed to create 2 VLANS and they both work (and can access the internet), but they can't communicate with each other.VLAN1 has an IP range starting 10.4.160 and VLAN2 has an IP range starting 10.6.192.Is it VLAN routing that I'm looking for?
View 1 RepliesHow is it possible to configure 2 VLANs to communicate with each other on the same switch? I have managed to create 2 VLANS and they both work (and can access the internet), but they can't communicate with each other.VLAN1 has an IP range starting 10.4.160 and VLAN2 has an IP range starting 10.6.192.Is it VLAN routing that I'm looking for? My switch is Netgear GSM7328FS.
View 1 Replies View RelatedI just recently switched from the WRVS4400N to the RV180W. I have 4 VLANs, and I want VLANs 1, 2, 3 to communciate freely, but I DONT want VLAN 4 to communicate with anybody, just Internet access. On the WRVS4400N, I was able to do this using the Firewall > IP Based ACL. I notcied that the RV180W, does not have such an option. I am sure there is something I am missing, I just cant find out how to isolate VLAN 4.
View 5 Replies View RelatedI have a situation where i am installing SGE2000Ps to replace my old switches and configuring VLANS. The time clock will not communicate across the VLANS. If I unplug the network cable and plug it back in I will get two successful pings. If i use a PC configured with the same network settings as the time clock and plug it into the port for the time clock it communicates fine.
View 9 Replies View RelatedThe router 861 Fast ethernet have support for wan protocol L2TP ?
Can I configure the router to use L2TP wan protocol to communicate the wan FE port to my ISP ?
If yes wath is the way ( CLI or Cisco E[press Professional Configurator ?)
I'm trying to configure an ASA to communicate with an AD environment that is only using LDAP Secure (LDAPS). I've configured authentication to ASA's with LDAP lots of times, though never with LDAPS.
Presumably there is a procedure to install a certificate in the same way as an RSA sig in VPN.
Need to configure a TEG-S2620is switch (Trendnet) with VLANs I need to set TWO VLANs and make them communicate with eachother via the 802.1Q protocol. These are the details:
VLAN ID 102
Port 20 (802.1Q)
Port 21
VLAN ID 144
Port 20 (802.1Q)
Port 22
Port 23
Port 24
how to configure this setup on our switch?
I am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
I am a novice at setting up Cisco routers, I have a few years of networking form the server side of things just beginning to work on the switch side. I am trying to configure a sg200-8 to have three VLANs.
Here are the steps i used:
Create VLAN:
VLAN
VLAN ID: 10
VLAN Name: 22 lab network
Apply
VLAN
VLAN ID: 20
VLAN Name: 23 lab network
Apply
[code].....
How to configure dynamic VLANs (IP subnet-based) using Nortel JDM? My company is now using port based VLAN and it wastes a lot of time reconfiguring the port to its VLAN everytime their devices moved from one place to another place. So I think using IP subnet-based VLAN might solve the problem?
View 1 Replies View RelatedI'm trying to configure a dhcp service on a router for some vlans.I would like to give the range 172.16.0.0 - 172.16.10.255 to vlan 10, 172.16.20.0 - 172.16.20.255 to vlan 20.for some reason it doesn't work?here's the config.
ip dhcp excluded-address 172.16.0.1
ip dhcp excluded-address 172.16.20.1
ip dhcp excluded-address 172.16.30.1
ip dhcp pool vlan10
network 172.16.0.0 255.255.0.0
[code]...
I saw a post in [URL] that was close to what I need to do. But this site seems a better place to ask a question. We need to install a second switch (SF300-24P) to an existing network with an SF300 48P and an ASA5500 for gateway/firewall etc. the network on the 48p switch is 192.168.1.xx. We want to use the new switch for ip cameras and 192.168.2.xx.
I will assume I need to set up a vlan on the 24 port switch for the 192.168.2.xx ip range, i will call this vlan20. I will guess that I need to pick a port from the 48p switch and create vlan20 on the 48p switch to access the 24p switch. I want users on the 192.168.1.xx network to be able to access cameras on the 192.168.2.xx network. Do I need to add a line in the asa config file for the new switch?
is it possible with LMS 4.0 and VLAN Port Assignment also to configure auxiliary vlans?
1. I selected Configuration > Workflows > VLAN > Configure Port Assignment.
2. Selected my device (a test switch WS-C3560-8PC-S)
3. Clicked List Ports
All ports were listed, port Fa0/1 has only a native vlan, the ports Fa0/2 - 8 have native and voice vlans (auxiliary) configured manually.
So when I want to configure the voice vlan for Fa0/1 the voice vlan is set as the native one.
Is it only possible to configure the native vlans with the VLAN Port Assignment of LMS 4.0 ?
make a couple of SF300 switches to work properly with a C2960S-48TS-L that acts as core switch/basic router. I can't seem to figure out how to assign VLANs correctly in trunk and access mode on the SF300. The 2960S are a no brainer with IOS commands but the webgui in the SF300 is a pain.
I've configured the 2960S with 3 VLANs and I would like to have the SF300 switches connect to the C2960S-48TS-L through VLAN trunk and then configure the ports on the SF300 switches to belong to the assigned VLANs of my choosing. I would also like to have all the SF300 switches management interface in VLAN 50.
I've partially described the enviroment below.
VLANs
Data VLAN 10: 192.168.10.0
Management VLAN 50: 10.20.30.0
Voice VLAN 100: 10.10.10.0
[Code].....
I am facing problem in configuration with SF-200-24P Switch . I am failed to configure two vlans on same access port i.e. data vlan and voice vlan. there is an option of auto voice vlan with vlan 1 and i changed to our voice vlan i.e. vlan 101 but didnt work. I tried many options. when i assign single vlan on each
access port it works . I have to configure like to work both data vlan and voice vlan with one access port. I worked on enterprise cisco switches its simple but on small business switch first time i am working.
I have problem with IPV6 connectivity, i have two Cisco 3550 switch and they are connected over a trunk link. The ios is c3550- ipservicesk9-mz. 122- 44.SE6 , I have configured vlans on both switches and i numbered one vlan to vlan 91 ,they can ping each other when i configure ipv4 on both vlans so trunk link is functional, but when i m using IPV6 they can't ping each other!! they can only ping their own ip address not each other. [code]
View 11 Replies View RelatedI can't seem to find any info on how to configure 2 DHCP server pools on a C3750, to use with 2 user vlans. The purpose is that users in vlan 1 should get an IP address from DHCP server1, and users in vlan 2 should get an IP address from DHCP server2. Both DHCP servers are configured in a stack of C3750 switches, which acts a a L2 switch.
View 2 Replies View RelatedI have a an ASA 5520 connected to a Layer 3 (3750) switch (Inside) and a connection to a 2960 switch (Outside) to get to the internet. . I have created vlan interfaces on the 3750 switch and enabled ip routing on the switch to enable the vlans to communicate with each other.
Vlan Interfaces on the switch:
Vlan 100 172.17.1
Vlan 200 172.18.1
Vlan 300 192.168.3.1
I want the devices connected to the 3 vlans to be able to pass through the firewall and get out to the internet.I have connected the ASA to the 3750 by routed interfaces (10.10.10.1) --------- (10.10.10.2) and they are able to ping each other.I have also put a default route on the 3750 sending all traffic from the switch to the ASA inside interface (10.10.10.1)The issue that i am having is that the ASA also connects to a 2960 which has a connection to the Internet, and they are handing off an ethernet connection from the 2960 that sits in VLAN 55 (Vlan 55 is the Internet accessible vlan).How do I configure my ASA to send all traffic from my (3) vlans to the interfaces that connects to the 2960 switch?
I need to configure two VLANs in my home network to separate a server 1 with VM from another part of network with server 2 and wifi clients. Is it possible to keep DHCP server and internet access on E2500 enabled for both vlans? If so, how should I configure ports tagging (variant shown on screen shoot below doesn't work).
View 5 Replies View RelatedHow to configure traffic flow between computers inside VLANs and a routed port? Here is the setup details:
1. Switch 3750-X
2. VLAN 100 - ( SVI IP address 192.168.100.1 /24)
3. VLAN 200 - ( SVI IP address 192.168.200.1 /24)
4. routed port gi1/0/48 (IP address 192.168.150.1 /24). Note: this port is directly connected to a firewall ASA 5520 port IP 192.168.150.100 /24
Ip routing is enabled on the switch and inter vlan traffic is flowing ok. I can ping the routed port gi1/0/48 from any computer connected in the VLAN 100 or 200. For example computer with IP 192.168.100.25 can ping the routed port 192.168.150.1. Switch can ping firewall port 192.168.150.100 and the 'sh ip route' command shows the network 192.168.150.0 /24 as directly connected network.
any computer in the two VLANs CANNOT ping firewall ASA port 192.168.150.100 Is it because inter VLAN routing does not work with a routed port on L3 switch? I looked up fallback bridging, but it is meant for non IP traffic.The goal is I am trying to set the ASA port as an internet gateway for VLANs.
Can't get into my netgear router to config it. I have tried using 192.168.0.1 and 192.168.1.1. So far it will not give me a window to log in. It has allways work before on xp pro, but now i am using win 7 on my new computer.
p.s. the router is a Netgear model # WGR614
I think it should be possible to create an IPSec tunnel between a Netgear FVS336Gv2 firewall/router and AWS VPC however, I've been unable after several tries. How do I setup a connection for a Amazon VPC?
View 1 Replies View Relatedupgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies View RelatedMy question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies View RelatedIs it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies View RelatedHow do i configure my netgear router to my samsung blu-ray player to allow wireless connection?
View 2 Replies View RelatedI've two routers, one which i got from BSNL when opted for internet connection. Its a Utstartcom Type II wireless modem and the other which i got from a friend is Netgear WGR614 wireless modem/router.Now coming to the real picture. I've the BSNL wireless modem connected and working perfectly on the 3rd floor on one PC, but NOT configured for wireless access and i've another PC on Ground Floor where i need an internet connection. Fortunately, i got a router/modem which is Netgear WGR614. I do not want a wired connection between these two PCs then wanted to try the wireless way?
View 1 Replies View RelatedI have a Netgear WGR614 wireless router connected to my WOW DSL modem and utilize WPA as security. wireless signal is good on first floor but drops significantly in my basement. I have a Netgear WG102 AP I would like to configure as a repeater and place in my basement to boost the WGR614 signal strength. What configurations must I apply to both or either devices to achieve this setup?
View 3 Replies View Relatedi am unable to configure my netgear router with my clear modem
View 1 Replies View RelatedHow do I configure and set up my desktop to get on my neighbors internet connection with the netgear wireless adapter.
View 3 Replies View RelatedI have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
View 7 Replies View RelatedWE have to deploy ASA5585 in between User vlans & server vlans. we have to find all the ports that needs to be opened on firewall. any tools to do same.
View 2 Replies View RelatedIn order to feed my netgear dgn1000 adsl modem/router with a rca roadrunner modem with ethernet single jack do I enable NAT or not on Netgear router and do I use router as DHCP or not?
View 2 Replies View Related