How to configure dynamic VLANs (IP subnet-based) using Nortel JDM? My company is now using port based VLAN and it wastes a lot of time reconfiguring the port to its VLAN everytime their devices moved from one place to another place. So I think using IP subnet-based VLAN might solve the problem?
View 1 RepliesI have problem with subnet based groups in Cisco Prime LMS 4.1.
Admin > System > Group Management > Device
I've been following examples made in this article with no luck:[URL]
Quote:
Understanding Subnet Based Groups #
The Subnet based groups use the following name format:
#
Subnet -- Subnet Mask.
The network topology is like this. Router with DHCP_Server on it.
VLAN 10
VLAN 20
VLAN 30
My question is how to configure the router so that all devices on all 3 VLANS can obtain IP from the router. I've tried to enable proxy arp on all interfaces and create sub interfaces and trunk them to their appropriate vlans, but I can't specify the gateway on all trunked sub interfaces because I get a warning that addresses overlap. Then I tried to set access-group on all sub-interfaces and still doesn't work.
I have a home office with multiple VLANS/subnets I have many VPNs that connect only a specific subnet to a specific remote offfice. On a 5520, can I create a S2S VPN to different remote offices that have the same IP scheme, but from different home office subnets? For example at my home office let's say I have two independant, distinct VLAN/subnets: 192.168.140.0/24 and 192.168.150.0/24. Can I create an S2S from the 140 subnet to a remote office with a 10.10.10.0 addressing scheme and another S2S from the 150 subnet to a totally different office also with a 10.10.10.0 scheme?
View 1 Replies View RelatedAfter a long effort I managed to get my WRVS4400N to work and provide a stable WLAN/LAN and to define all network devices in my home office. It is running the latest firmware (2.0.1).
I created a seperate SSID and a vlan for it (vlan ID is 3 and IP is 192.168.1.xxx while the default vlan IP is 192.168.0.xxx).
My plan is to use that SSID/vlan for the kids and block some bad content for them via the router there.
I want to make a ACL for that vlan but in the computer list option I can only specify ranges in the default VLAN segment (192.168.0.xxx) while in practice I need the 192.168.1.xxx segment.
I can't switch to .0.xxx as some devices are hard wired to be .1.xxx on my network.
My customer requires the hostport on an access switch to be allocated to a specific Vlan based upon the AD Group that the user is a memeber of ? I am planning to setup NAC in a Real Gateway OOB deployment, using an ACS 5.2. I was initially thinking that the initial authentication server would be the ACS and then the AD, which using group mappings within the AD, I could then assign the user to a specific ACS group and then pass a Radius attribute back to the NAC manager for processing?
View 2 Replies View RelatedI want to buy an AIR-SAP1602I-E-K9 and I don't know if I can configure a MAC-BASED ACL with this AP, because I must permit the access of the wireless netwok only to determined wireless devices.
View 4 Replies View RelatedJust got a new SGE2010P layer 3 switch. I'm trying to configure Vlan to reach a few subnet. I have the original 192.168.1.0/24 as vlan1. I want to reach our WiFi subnet 192.168.10.0/24. The WIFI router is directly connected. It's new for me as the previous Job i was sorking with a ws-3750-48.
i did from console change my switch to layer 3 mode... ( i want it as the DGW for each Vlan)from the web interface, i create a vlan4 for our WIFI Next i go to ipv4 to add an IP address to vlan 4 like 192.168.10.254 /24 As soon as I apply the IP the switch stop responding, Ping request time out.. i need to reboot the switch..
I need to configure the C3560-24TS, QoS control by IP or subnet.i tried to study books and videos many times but still feel i am not well known about QOs...
View 1 Replies View RelatedI have cisco 2504 WLAN controller with 7.4 IOS. My query is can I configure the MAC authentication with certificate based. And without using any external servers like Radius, ACS and LDAP.
May I know, If there is a option on WLC…
configuring policy based route for my cisco router?Basically, I have a 2811 cisco router with 2 ADSL ports. 1 port is for iiNet line and another port is for Telstra line.I want to configure a policy based route on the router so that:Any traffic coming from 1 internal IP (i.e. 172.16.x.1) will go through iinet line (i.e. Dialer 0) interface.Any traffic from rest of the office will go through the Telstra line (i.e. Dialer 1) interface. Is there any easy way to configure this policy based route?
View 8 Replies View RelatedI have a network setup where two servers from inside need to communicate with a remote network via 2 VPN gateways. The destinations are same. However, the chalange is each server need to follow it's own VPN gateway. Since i can't configure PBR (policy based routing) in ASA, can i configure something like MAC Address based routing. I can't use destination based routing since the remote network are reachable from the both VPN Gateways.
View 1 Replies View RelatedHow is it possible to configure 2 VLANs to communicate with each other on the same switch? I have managed to create 2 VLANS and they both work (and can access the internet), but they can't communicate with each other.VLAN1 has an IP range starting 10.4.160 and VLAN2 has an IP range starting 10.6.192.Is it VLAN routing that I'm looking for? My switch is Netgear GSM7328FS.
View 1 Replies View RelatedI have some questions about how to configure my Cisco 1941 with a routed subnet from my ISP to forward them to 1 or more servers in my LAN.1 Routed subnet /29 from my ISP (over a fiber connection).In my LAN I have (at the moment) 3 servers, and about 15 clients.I would like to use the first ip address from the routed subnet for internet traffic from all the clients in the LAN.I would like to use the second ip address from the routed subnet for server1 so that server1 accept some allowed connections and that server1 connects to the internet with the second ip address from the routed subnet
I would like to use the thirth ip address from the routed subnet for server2 so that server2 accept some allowed connections and that server2 connects to the internet with the thirth ip address from the routed subnet.I would like to use the fourth ip address from the routed subnet for server3 so that server3 accept some allowed connections and that server3 connects to the internet with the fourth ip address from the routed subnet.[code]
Have our public IP address space masked on /24 at our Internet Router. The router portion of 3845 connects to Internet, while the internal switch connects to my internal network and seeds it with the public address space. The switch had a port configured no switchport (L3) with an ip address with /24 (ie 67.63.145.1 /24) this connects to internal IPS/IDS then to Firewall which NATs to internal, then packet shaper, web filter etc etc etc. I need to test my ISP speed so I need to "break in" to the link between the switch and the IPS/IDS. I figured I could configure another port on the switch on the 3845 but my problem is the port to my network is routed and is masked on entire /24. I tried to configure a port on VLAN 1 and give myself an available address in the L3 address space and this did not work (figured it would not but gave it a try)
Any way to get two ports configured to use the same subnet while one is a L3 routed port and the other is just part of that layer 3 routed network?
Our ISP has set up a Cisco 2431-16fxs IAD (dual WAN) in one of our locations. It is used to connect the devices (PCs and SIP phones) on our LAN to internet (via 1st WAN port) and ISP's MPLS-based voip network (via 2nd WAN port).
We have 2 LAN subnets - the first subnet (PCs) requires internet access only, so it goes out via the 1st WAN port. The 2nd subnet (SIP phones) is connected the MPLS network (via 2nd WAN port).
We would like to have the SIP phones (that connects to MPLS-based network 192.168.1.x) to be able to access the internet. Is it possible to configure the IAD so that the phones are routed based on destination network; i.e. anything to 192.168.1.x via 2nd WAN port, anything else to the internet via the 1st WAN port?
Need to configure a TEG-S2620is switch (Trendnet) with VLANs I need to set TWO VLANs and make them communicate with eachother via the 802.1Q protocol. These are the details:
VLAN ID 102
Port 20 (802.1Q)
Port 21
VLAN ID 144
Port 20 (802.1Q)
Port 22
Port 23
Port 24
how to configure this setup on our switch?
How is it possible to configure 2 VLANs to communicate with each other on the same switch? I have managed to create 2 VLANS and they both work (and can access the internet), but they can't communicate with each other.VLAN1 has an IP range starting 10.4.160 and VLAN2 has an IP range starting 10.6.192.Is it VLAN routing that I'm looking for?
View 1 Replies View RelatedI am having problems accomplishing these tasks with my new SG 200-18.
I have a LinkSys WRT54G2 connected to port 1. I would like ports 2-8 to be in one VLAN with access to the Internet and to be able to share their printers, hard drives, etc. with other computers on ports 2-8. I would like each of ports 9-16 to be on a separate VLAN with access only to the Internet and no other ports on the switch. I would like to be able to manage the switch from any of the ports 2-8.
After I create the VLAN 1009 (see screenshot below), port 9 can browse the Internet and cannot see the other ports on the switch which is correct. However, ports 2-8 can no longer access the switch at 192.168.1.20 in order to manage the switch.
I am a novice at setting up Cisco routers, I have a few years of networking form the server side of things just beginning to work on the switch side. I am trying to configure a sg200-8 to have three VLANs.
Here are the steps i used:
Create VLAN:
VLAN
VLAN ID: 10
VLAN Name: 22 lab network
Apply
VLAN
VLAN ID: 20
VLAN Name: 23 lab network
Apply
[code].....
I'm trying to configure a dhcp service on a router for some vlans.I would like to give the range 172.16.0.0 - 172.16.10.255 to vlan 10, 172.16.20.0 - 172.16.20.255 to vlan 20.for some reason it doesn't work?here's the config.
ip dhcp excluded-address 172.16.0.1
ip dhcp excluded-address 172.16.20.1
ip dhcp excluded-address 172.16.30.1
ip dhcp pool vlan10
network 172.16.0.0 255.255.0.0
[code]...
I saw a post in [URL] that was close to what I need to do. But this site seems a better place to ask a question. We need to install a second switch (SF300-24P) to an existing network with an SF300 48P and an ASA5500 for gateway/firewall etc. the network on the 48p switch is 192.168.1.xx. We want to use the new switch for ip cameras and 192.168.2.xx.
I will assume I need to set up a vlan on the 24 port switch for the 192.168.2.xx ip range, i will call this vlan20. I will guess that I need to pick a port from the 48p switch and create vlan20 on the 48p switch to access the 24p switch. I want users on the 192.168.1.xx network to be able to access cameras on the 192.168.2.xx network. Do I need to add a line in the asa config file for the new switch?
is it possible with LMS 4.0 and VLAN Port Assignment also to configure auxiliary vlans?
1. I selected Configuration > Workflows > VLAN > Configure Port Assignment.
2. Selected my device (a test switch WS-C3560-8PC-S)
3. Clicked List Ports
All ports were listed, port Fa0/1 has only a native vlan, the ports Fa0/2 - 8 have native and voice vlans (auxiliary) configured manually.
So when I want to configure the voice vlan for Fa0/1 the voice vlan is set as the native one.
Is it only possible to configure the native vlans with the VLAN Port Assignment of LMS 4.0 ?
make a couple of SF300 switches to work properly with a C2960S-48TS-L that acts as core switch/basic router. I can't seem to figure out how to assign VLANs correctly in trunk and access mode on the SF300. The 2960S are a no brainer with IOS commands but the webgui in the SF300 is a pain.
I've configured the 2960S with 3 VLANs and I would like to have the SF300 switches connect to the C2960S-48TS-L through VLAN trunk and then configure the ports on the SF300 switches to belong to the assigned VLANs of my choosing. I would also like to have all the SF300 switches management interface in VLAN 50.
I've partially described the enviroment below.
VLANs
Data VLAN 10: 192.168.10.0
Management VLAN 50: 10.20.30.0
Voice VLAN 100: 10.10.10.0
[Code].....
I am facing problem in configuration with SF-200-24P Switch . I am failed to configure two vlans on same access port i.e. data vlan and voice vlan. there is an option of auto voice vlan with vlan 1 and i changed to our voice vlan i.e. vlan 101 but didnt work. I tried many options. when i assign single vlan on each
access port it works . I have to configure like to work both data vlan and voice vlan with one access port. I worked on enterprise cisco switches its simple but on small business switch first time i am working.
I want to configure IEEE 802.1x port-based authentication on cisco switches, preferable 2960 series. Which models support this feature?. I have try with some older switches but it doesn't works properly on everyone. I have upgraded them whitout better results, there is namely an issue with TLS handshaking on some switches which produces authentication to fail.
View 1 Replies View RelatedI have problem with IPV6 connectivity, i have two Cisco 3550 switch and they are connected over a trunk link. The ios is c3550- ipservicesk9-mz. 122- 44.SE6 , I have configured vlans on both switches and i numbered one vlan to vlan 91 ,they can ping each other when i configure ipv4 on both vlans so trunk link is functional, but when i m using IPV6 they can't ping each other!! they can only ping their own ip address not each other. [code]
View 11 Replies View RelatedI can't seem to find any info on how to configure 2 DHCP server pools on a C3750, to use with 2 user vlans. The purpose is that users in vlan 1 should get an IP address from DHCP server1, and users in vlan 2 should get an IP address from DHCP server2. Both DHCP servers are configured in a stack of C3750 switches, which acts a a L2 switch.
View 2 Replies View RelatedI have a an ASA 5520 connected to a Layer 3 (3750) switch (Inside) and a connection to a 2960 switch (Outside) to get to the internet. . I have created vlan interfaces on the 3750 switch and enabled ip routing on the switch to enable the vlans to communicate with each other.
Vlan Interfaces on the switch:
Vlan 100 172.17.1
Vlan 200 172.18.1
Vlan 300 192.168.3.1
I want the devices connected to the 3 vlans to be able to pass through the firewall and get out to the internet.I have connected the ASA to the 3750 by routed interfaces (10.10.10.1) --------- (10.10.10.2) and they are able to ping each other.I have also put a default route on the 3750 sending all traffic from the switch to the ASA inside interface (10.10.10.1)The issue that i am having is that the ASA also connects to a 2960 which has a connection to the Internet, and they are handing off an ethernet connection from the 2960 that sits in VLAN 55 (Vlan 55 is the Internet accessible vlan).How do I configure my ASA to send all traffic from my (3) vlans to the interfaces that connects to the 2960 switch?
I need to configure two VLANs in my home network to separate a server 1 with VM from another part of network with server 2 and wifi clients. Is it possible to keep DHCP server and internet access on E2500 enabled for both vlans? If so, how should I configure ports tagging (variant shown on screen shoot below doesn't work).
View 5 Replies View RelatedI have 4 different OfficeJet Pro 8600's installed in 4 different locations, bought from different vendors. In every case I get the same problem.This is a Networking issue. All printers are wired to the network.The printer is not the cause of the problem. The problem persists even if the printer is off.The problem is that: When computer is left on overnight, the next morning, webpages can not be accessed, and the network communication with the printer is gone. You can not print and you can not browse.
View 1 Replies View RelatedI have an all in one hp officejet 8600 plus and i cant get it to connect to my laptopOperating system is windows 7. It's connected to the network, laptop connected to network, but printer isn't connecting to laptop. This function is handy so i can sent scans to an email or folder on my computer but it wont connect. I keep getting an error, unable to connect with printer over network. I've been on the phone with hp for 7 hours so far in 2 days and they still don't have an answer!!! I called dell and they said its a software issue and need to pay $90 for them to fix it
View 5 Replies View Relatedi have a dell inspiron 8600 running windows xp. the issue is it will let me connect to other wireless networks but not mine. i try to connect to mine , i enter my metwork key and it says please wait while windows connects. then after 30 seconds or so the box goes away and under connections mine is listed and says automatic but i am not connected. i have tried everything, even manually setting up network and entering network key and still nothing. oh n i know it isnt my router because i have another laptop connected to this network already and works fine
View 1 Replies View Related