Cisco Switching/Routing :: 3550 Ping Each Other When Configure Ipv4 On Both Vlans
Mar 5, 2013
I have problem with IPV6 connectivity, i have two Cisco 3550 switch and they are connected over a trunk link. The ios is c3550- ipservicesk9-mz. 122- 44.SE6 , I have configured vlans on both switches and i numbered one vlan to vlan 91 ,they can ping each other when i configure ipv4 on both vlans so trunk link is functional, but when i m using IPV6 they can't ping each other!! they can only ping their own ip address not each other. [code]
View 11 Replies
ADVERTISEMENT
Jul 24, 2012
The situation include 2 cisco routers an 2 switch 3550
so we have Router A in Vlan x access ----->Sw1----Trunk----Sw2<------Vlan y Access Router B I 've to enable rip1 on guys A and B ONLY !!! Avoiding any kind of tunnel I though it was all around fallBAck bridging ... but after days of tries ...
View 3 Replies
View Related
Jun 12, 2012
We have cisco 3550 switch i have configured 3 vlans in this switch vlans are not able to accessing internet
View 7 Replies
View Related
Oct 9, 2012
I have a test switch (Cisco 3550) that I want to set up with 6 Vlans and 2 trunk ports. I want to be able to access a virtual server conected to the trunk ports from the switch ports. Ports Fa0/1 to 8 are in a vlan port fa0/9 to 16 another vlan etc. Ports Fa0/47 and 48 are the trunk ports. This is a lab environment so the the switch is the only device being used.
View 4 Replies
View Related
Apr 27, 2013
They have a locked Cisco Router which is from the ISP and its confed on a fa 0/0 interface to share Internet access on the network. The ip on that interface is 195.198.11.217 255.255.255.252 and i tried it with a PC (set my personal ip to .218 and entered their dns info (195.67.199.27) and it is working. The question is now. My friend found a 3550 laying around and since the ISP wont let them conf their router he wants to use the 3550 to create 2 vlans with internet access and without access to eachother. Vlan 10 for the desktops and Vlan 20 for the wireless (Moving on to some netgear wireless switches) How would you configure the 3550 for this to work?
View 23 Replies
View Related
Feb 22, 2012
I have a small cisco switch cluster (seven different 2924, 3524cisco switches) with 3550 as a cluster control which does all the inter vlan routing that works fine.
This cluster is in semi production PBX interop testing lab. This is a closed network without internet access and not connected to our corporate network.However now I have to add this capability so some equipment in the lab can get Microsoft updates over the internet.
I've created a port on a 3550 (fa0/19) and connected it to another network that has internet access. It picked an ip address and when I'm logged in to the 3550 I can ping hosts on the outside network. However I can't ping any hosts on that network from any hosts that are connected to my vlans.I've tried a few different things, but still can't make it to work.
Here is a short version of my 3550 configuration:
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime
no service password-encryption
[code]....
View 13 Replies
View Related
Feb 24, 2012
I am testing on lab equipment (2 Catalyst 3550 and 1 Catalyst 3560) HSRP version 1 and 2.I successfully created a load balancing between the two Catalyst 3550 on a couple of vlans (11 and 12) on ver 1
now, just adding the command "standby xx version 2" my hosts on the 2 vlans are completely unable to ping the virtual IP def. gw on debugging i checked that msgs are exchangedthe two cat 3550 are seeing each other on HSRP (active / standby roles)the real ip addresses are pingable rebooted the swiches (just as a last resort try)deleted arp chache on hostsremoved the auth on hsrp all of this no effect.
i also tried to modify the priority on the cat 3560 (before he was on both vlans in standby) to make it the active one and with the same config it worked flawlessly.
My only idea is that there is a bug on CATs 3550 (IOS: c3550-ipservicesk9-mz.122-55.SE4.bin) [code]
View 11 Replies
View Related
Feb 19, 2012
We had re-arranged and purchased new public ips and changed with new modem. Following is the new network setup diag
I have started the configuration, but stucks at a point. Current configurations setup and ip assigment is as follows
ISP modem/router(192.168.3.254)-->(192.168.3.1)1811W Router(192.168.2.254)-->(192.168.2.1)3550(interface vlan 10 - 10.0.1.254, interface vlan 192 - 192.168.1.254)--trunk-->2950
1)Configured 3550 as layer 3 switch and create a default route to 192.168.2.254
2) Configured 2 static routes(for 2 vlan range traffic) and one default route to 192.168.3.254
3) ip pass through is not configured yet, still the public ip is configured at the isp router
1811 static route configs
------------------------------------
Ip route 0.0.0.0 0.0.0.0 192.168.3.254
Ip route 192.168.1.0 255.255.255.0 192.168.2.1
Ip route 10.0.1.0 255.255.255.0 192.168.2.1
3550 static route config
--------------------------------------
Ip route 0.0.0.0 0.0.0.0 192.168.2.254
Testing results 1)All lan communications are working fine(inter vlan also), ping to all servers from router is getting and ping to outside public ips are getting from router,but not getting ping from switch 3550 to 192.168.3.254 and any of the public ips(internet).
View 4 Replies
View Related
Oct 30, 2012
I have two 1231G Aironet's that work correctly when I connect them to my Catalyst 3548XL and my 3550-48-XL switches. When I connect them to the 3550-24-PWR switch I do see them when I issue sh cdp nei det. It shows me the IP of the wireless router. But when I ping the Aironet, I do not get any replies. If I plug the Aironet into my 3548XL and ping the IP, I get 5 replies. Here is the port config on both switches:
switchporrt trunk encapsulation dot1q
switchport native vlan 100
switchport allowed vlan 1,69,100,125,200,1002-1005
switchport mode trunk
spanning-tree portfast
Here is the sh cdp nei det results:
Device ID: North_AP.mtd.home
Entry address(es):
IP address: 192.168.100.104
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: FastEthernet0/3, Port ID (outgoing port): FastEthernet0
[code]....
I have tried two versions of the IOS on the 3550PWR switch. Right now its: c3550-ipservices-mz.122-44.SE6
View 5 Replies
View Related
Aug 3, 2012
I was trying to config qos on 3550 interface
Match protocol is not supported for this interface
So does this mean that qos is not supported on 3550?
View 4 Replies
View Related
Nov 16, 2011
I have router connected to 2 3550 switches directly. 3550A and B switches are running HSRP. OSPF is running between Router and 2 switches.
From Switch B i can ping the Router Wan interface but not the internet sites. from Switch A i can ping any sites?
Switch B
3550SMIB# sh ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1
[Code]......
View 7 Replies
View Related
Sep 18, 2012
The layer 2 switches are connected to layer 3 Switch via trunks, and routing between layer 2 switch ports with configured SVI's on 3550. All working fine. Now I'm trying to configure routing between 2800 and 3550, I tried connecting both Straight Throught and Crossover cables to the 2800 Fa0/0 and Fa0/1 ports as well as the switchports on 3550
No switchport commands are configured however, the lights do not go on for both straight through or crossover cables. I tried connecting 1750 routers but same result. My goal is to have all the VLANS routed to the internet with configuring NAT translation the router.
View 2 Replies
View Related
Oct 2, 2012
Is there a way to configure a DHCP server for my internal subnet of 192.168.20.1 which is on a 3550 layer 3 switch from my 5505 ASA Firewall.My subnet of 10.1.1.0/30 is connecting my 5505 to 3550. All I'm trying to do is run a DHCP server down to my hosts. The only options on ASA 5505 is
dhcpd address 192.168.20.1 - 192.168.20.254 outside or inside, which conflicts with my subnet of 10.1.1.0 used to connect my internal subnet of 192.168.20.1 for the whole network.
When I used my router it did not need the (inside, outside) keywords and just an ip helper-address command. How do I configure my my firewall DHCP server to propagate the 192.168.20.0 network through my 10.1.1.0 connection.
View 3 Replies
View Related
Jul 13, 2012
I have configured HSRP with InterVlan routing. All communication is flowing properly between the vlan's on Router A but when I test failover to Router B I cant ping ANYWHERE. I cannot ping any of the VLANS.
Also, From the primary router I cannot ping any of the interfaces on the secondary router.
I have 2 Cisco 1921 Routers configured for HSRP. Both the G0/1 ports plug into a Cisco 2960S 48 port POE switch (STACKED) (port 1 and port 2 which are trunked and allowing all vlans to pass through. And both of the G0/0 ports are plugged into a Cisco ASA5510.
I have attached a diagram of the setup and the interface configs of the routers.
View 1 Replies
View Related
Jul 18, 2012
last week I installed a new router (2911) in my network.We had to create two different VLANs for the new setup to work as wanted.I have a Windows 2008 R2 which is a Domain Controller for Active Directory on the ip address 192.168.0.195.That server (HP DL180 G6) has two NICs. One has the above IP address and the other one has 192.168.0.199.
On the other VLAN, I have a server, running the same OS, that I want to re-join, as it formerly was, the AD on the first server (192.168.0.195). This server has the new IP address 192.168.10.194.All these are connected to a Cisco switch SG 200-50 Gigabit Smart Switch. That one is connected to a Cisco 2911 router.
The problem is that, once the old 192.168.0.194 got to be 192.168.10.194, the 192.168.0.195 can't ping it anymore... At least not all the time... Sometime it works, sometimes not... Neither can't the 10.194 ping the 0.195 all the time. When one way works the other one doesn't... When one pings the other one successfully, the other one can't...
View 5 Replies
View Related
Feb 26, 2012
I am at a client that I upgrade from running a single 4507 to two Nexus 5548UP switches with two Nexus 2224 fex's connected. The other access layer switches are 2960S switches. I implemented hsrp on the nexus 5k's for redudancy. The issue they are having is that some networks cannot communicate with each other. All user vlans can communicate with the server vlan, but it is not running hsrp on the vlan interface (there is a reason for that, but it not relavent for this issue). The phone vlan, which is running hsrp, can communicate with all networks.
When I am connected to either 5k, they can communicate with all devices on all networks. However, I am on vlan 10, which is a user vlan. I can communicate fine with the server vlan (vlan 101 - not running hsrp) and the phone vlan (vlan 60 - running hsrp). I cannot communicate with vlan 30 or 40, which are both running hsrp. This makes absolutely no sense at all to me. I checked out trunk ports to be sure that vlans are allowed across the networks as well. There are no firewalls between the vlans or ACL's.
View 1 Replies
View Related
Jul 4, 2012
upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies
View Related
Sep 21, 2011
make a couple of SF300 switches to work properly with a C2960S-48TS-L that acts as core switch/basic router. I can't seem to figure out how to assign VLANs correctly in trunk and access mode on the SF300. The 2960S are a no brainer with IOS commands but the webgui in the SF300 is a pain.
I've configured the 2960S with 3 VLANs and I would like to have the SF300 switches connect to the C2960S-48TS-L through VLAN trunk and then configure the ports on the SF300 switches to belong to the assigned VLANs of my choosing. I would also like to have all the SF300 switches management interface in VLAN 50.
I've partially described the enviroment below.
VLANs
Data VLAN 10: 192.168.10.0
Management VLAN 50: 10.20.30.0
Voice VLAN 100: 10.10.10.0
[Code].....
View 5 Replies
View Related
May 1, 2012
I can't seem to find any info on how to configure 2 DHCP server pools on a C3750, to use with 2 user vlans. The purpose is that users in vlan 1 should get an IP address from DHCP server1, and users in vlan 2 should get an IP address from DHCP server2. Both DHCP servers are configured in a stack of C3750 switches, which acts a a L2 switch.
View 2 Replies
View Related
Jul 7, 2012
How to configure traffic flow between computers inside VLANs and a routed port? Here is the setup details:
1. Switch 3750-X
2. VLAN 100 - ( SVI IP address 192.168.100.1 /24)
3. VLAN 200 - ( SVI IP address 192.168.200.1 /24)
4. routed port gi1/0/48 (IP address 192.168.150.1 /24). Note: this port is directly connected to a firewall ASA 5520 port IP 192.168.150.100 /24
Ip routing is enabled on the switch and inter vlan traffic is flowing ok. I can ping the routed port gi1/0/48 from any computer connected in the VLAN 100 or 200. For example computer with IP 192.168.100.25 can ping the routed port 192.168.150.1. Switch can ping firewall port 192.168.150.100 and the 'sh ip route' command shows the network 192.168.150.0 /24 as directly connected network.
any computer in the two VLANs CANNOT ping firewall ASA port 192.168.150.100 Is it because inter VLAN routing does not work with a routed port on L3 switch? I looked up fallback bridging, but it is meant for non IP traffic.The goal is I am trying to set the ASA port as an internet gateway for VLANs.
View 4 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Dec 1, 2011
We have cisco 3550 switch i have configure 3 vlans in this switch. i have enable routing between this vlans but vlans not able to communicating with each other.
View 2 Replies
View Related
May 14, 2012
Can a F2 card handle 15000 BGP ipv4 route?
View 1 Replies
View Related
Dec 26, 2012
I am trying to setup my 3550 layer 3 switch to do hand out dhcp addresses for different vlans. It is connected to my router address 192.168.1.1. I setup a new vlan 3 and the dhcp pool.. The client gets a 192.168.3.2 address but am not able to ping the router and other clients and get out to the internet.
Here is the config that I have. I deleted the other ports because I am not using them. The vlan 3 client is on port fast Ethernet 0/17 and the router is connected to the fastethernet 0/1.
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code]....
View 12 Replies
View Related
Apr 18, 2012
I have a collapsed core design with routed ports between all components. Access layer switches, data center switches, core/aggregation. All routed (no spanning-tree at all).Now...I have to add an IBM BladeCenter with a BNT layer 3 switch to my topology. However, those nasties don't seem to support routed ports.How can I have a routed port on my cisco switch and a standard access port on the BNT and still establish an adjacency with an SVI? I am running OSPF, but I am labbing this in my home lab with 2 x 3550s and EIGRP.
On SW2:
*Mar 1 00:57:00.711: EIGRP: Received HELLO on Vlan100 nbr 10.1.1.1
*Mar 1 00:57:00.711: AS 999, Flags 0x0, Seq 0/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
*Mar 1 00:57:02.303: EIGRP: Sending UPDATE on Vlan100 nbr 10.1.1.1, retry 9, RTO 5000 tid 0
*Mar 1 00:57:02.303: AS 999, Flags 0x1, Seq 17/0 interfaceQ 0/0 iidbQ un/rely 0/0 peerQ un/rely 0/1
[code].....
View 10 Replies
View Related
Jul 24, 2007
Does Catalyst 3550 switch support inter vlan routing ?
View 12 Replies
View Related
Apr 11, 2012
Is L3 ip routing on by default in 3550s? If so is the "ip routing" command visible in the config file? If no - I assume that one would enable L3 routing with that config command.In general terms are there any IOS devices where ip routing is enabled and one would not see the "ip routing" command in config. I.E. if that command is not visible in the config could you assume there is no L3 capablity in that device?
View 1 Replies
View Related
Apr 26, 2012
I have a 3550 l3 switch configured as follows:
vlan 10 ports 1-10
vlan 21 ports 11-20
vlan 30 port 21-30
vlan 40 ports 31-40
default vlan should be vlan 21
I have the servers, switch and router connected to vlan 21. Vlan 21 works great I can browse the internet, but I cannot ping any other vlans. router is connected to fa0/19
[code]
Building configuration...
Current configuration : 4833 bytes
!
version 12.2
no service pad
[code]....
View 11 Replies
View Related
Mar 10, 2013
I'm having some problems setting up vlans to talk to each other on a 3550-12T switch. Its quite a simple setup I have, but I need to split my network up.
Currently I have a network of 192.168.25.0 255.255.255.0 I want to create a new vlan network of 192.168.30.0 255.255.255.0 So I have configured my vlan1 (default vlan) to have an ip of 192.168.25.250 for getting to the management page
I have created a vlan2 of 192.168.30.1 255.255.255.0 ?I have a port 10 linked to one of my 3560G's?In port 9 which is on vlan2 I have my pc plugged in with a static ip of 192.168.30.50 from the router I can ping any device on 192.168.25.x.
I can not ping 192.168.30.1 (which is my vlan2) nor can i ping the PC.
I have enabled ip routing But I dont have a default route, this is becase we don't have a router on the network.
View 18 Replies
View Related
Dec 2, 2011
I've been working with these two Cisco devices in my home off and on for several months now but I just can't take it anymore, I'm about to throw them away and go back to Linksys router.
I have a Cisco 2600 Router with only one Ethernet card in it so I have to trunk from my 3550 Switch to that device. I'd like to have my ISP and all users plug into switch and all trunk back to the router's sub interfaces. Currently, I have started over...again, and am unable to simply get the router and switch to ping each other if I put sub-interfaces on the router. See my configs:
2600 ROUTER:
Router#sho run
Building configuration...
Current configuration : 555 bytes
[code]......
3550 SWITCH:
Switch#sho run
Building configuration...
Current configuration : 2302 bytes
!
version 12.2
[code]..........
Port F0/24 is in VLAN 1, as are all ports but Port F0/1 which is my desktop PC. I mocked it up in Packet Tracer and it works just fine. This is just a simple setup and I'm making sure I can ping between switch and router before I move to each next step.
View 40 Replies
View Related
Mar 31, 2012
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
View 5 Replies
View Related
Dec 12, 2011
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
