Cisco Switching/Routing :: 1921 / HSRP - Cannot Ping Any Of VLANS
Jul 13, 2012
I have configured HSRP with InterVlan routing. All communication is flowing properly between the vlan's on Router A but when I test failover to Router B I cant ping ANYWHERE. I cannot ping any of the VLANS.
Also, From the primary router I cannot ping any of the interfaces on the secondary router.
I have 2 Cisco 1921 Routers configured for HSRP. Both the G0/1 ports plug into a Cisco 2960S 48 port POE switch (STACKED) (port 1 and port 2 which are trunked and allowing all vlans to pass through. And both of the G0/0 ports are plugged into a Cisco ASA5510.
I have attached a diagram of the setup and the interface configs of the routers.
I am at a client that I upgrade from running a single 4507 to two Nexus 5548UP switches with two Nexus 2224 fex's connected. The other access layer switches are 2960S switches. I implemented hsrp on the nexus 5k's for redudancy. The issue they are having is that some networks cannot communicate with each other. All user vlans can communicate with the server vlan, but it is not running hsrp on the vlan interface (there is a reason for that, but it not relavent for this issue). The phone vlan, which is running hsrp, can communicate with all networks.
When I am connected to either 5k, they can communicate with all devices on all networks. However, I am on vlan 10, which is a user vlan. I can communicate fine with the server vlan (vlan 101 - not running hsrp) and the phone vlan (vlan 60 - running hsrp). I cannot communicate with vlan 30 or 40, which are both running hsrp. This makes absolutely no sense at all to me. I checked out trunk ports to be sure that vlans are allowed across the networks as well. There are no firewalls between the vlans or ACL's.
I am looking to simply monitor Port-Security , Error-Disable and HSRP. I would like to receive an email when any of these are triggered.
Port Security - Port Is shut down Err-Disable - Port goes into err-disable state (securedown) HSRP - When HSRP standyby changes are detected
I need to receive emails with any of the able are triggered. What is the easiest way to do this? I know SNMP is the main option but I have never worked with SNMP and dont understand it too much.
I have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
I wanted to know about EHWIC 8-Port configuration? We create Data and Voice VLANs and assign 8 ports to the VLANs. So how do VLANS communicate with each other? We cannot make Gi0/1 as sub interfaces and assign the same subnet IP’s as of VLAN IP’s , it wont accept. On 1921 router Assume Gi0/0 we connect to MPLS WAN. What happens to Gi0/1 where do we connect this?
We have an OSPF network with four 6500 Distribution Switches. They are fully meshed and see each other as peers and are sharing routes. Off of one pair (Border) there is a setup of 3750G siwtches that go off to another network and they do not run OSPF. Between the Border Dist and the 3750G Switches we run HSRP. The 3750G side uses HSRP GP 192 and the Dist Side uses HSRP 192.There are static routes on the 3750G pointing to the Dist HSRP address to get back to network.Pings fail from the OSPF side to the HSRP address on the 3750G side.If I do a trace from the OSPF side to the HSRP address it hits one border dist switch then the other and fails.If I have static routes on both border dist switches pointing to the HSRP on the 3750side, do we need to change the metric on one dist so that it is preferred over the other or should the router Id take care of that?
I have router connected to 2 3550 switches directly. 3550A and B switches are running HSRP. OSPF is running between Router and 2 switches.
From Switch B i can ping the Router Wan interface but not the internet sites. from Switch A i can ping any sites?
Switch B 3550SMIB# sh ip routeCodes: C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1
I wounder if there is any way to ping the local deviceses connected to a network hosted by a Cisco 1921 router? I wan't to be able to ping the device(computer name) but currently cant do that.
last week I installed a new router (2911) in my network.We had to create two different VLANs for the new setup to work as wanted.I have a Windows 2008 R2 which is a Domain Controller for Active Directory on the ip address 192.168.0.195.That server (HP DL180 G6) has two NICs. One has the above IP address and the other one has 192.168.0.199.
On the other VLAN, I have a server, running the same OS, that I want to re-join, as it formerly was, the AD on the first server (192.168.0.195). This server has the new IP address 192.168.10.194.All these are connected to a Cisco switch SG 200-50 Gigabit Smart Switch. That one is connected to a Cisco 2911 router.
The problem is that, once the old 192.168.0.194 got to be 192.168.10.194, the 192.168.0.195 can't ping it anymore... At least not all the time... Sometime it works, sometimes not... Neither can't the 10.194 ping the 0.195 all the time. When one way works the other one doesn't... When one pings the other one successfully, the other one can't...
I have problem with IPV6 connectivity, i have two Cisco 3550 switch and they are connected over a trunk link. The ios is c3550- ipservicesk9-mz. 122- 44.SE6 , I have configured vlans on both switches and i numbered one vlan to vlan 91 ,they can ping each other when i configure ipv4 on both vlans so trunk link is functional, but when i m using IPV6 they can't ping each other!! they can only ping their own ip address not each other. [code]
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability delay down 1 up 1 ! track 20 rtr 2 reachability delay down 1 up 1 ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
I am facing an isssues with 7609 for LAN switching , based on LAN (VRRP/HSRP) feature.Actually we are having ES+ cards (on 7609) and we are using multiple groups(say 350 vrrp groups) running on the router . the routers are connected as router 1>>> mux(which is working as switches)>>> router2
my questing are
1. does their will be "multicast packets" (for VRRP/HSRP group) "from backup router to Master router", when in stable state( ie when Master and backup are already chosen) , or the packet from backup to master should be unicast.I know for sure, the packet from master to back is multicast packets denstination to Multicast IP packet and To MAC address.I am not sure but I think from backup to master it should be multicast
2. what is frequency of these packets( from backup to master)
3. As i have multiper group on a single interface ( we are using q-in-q), when the connectivity from router's is broken, then does all the groups will muticast their active roll in the lan sengment "at once" or it will be in a groups say 100 groups at once, and after few ms few 100's and sone ( as is on OSPF or RIP)
we are in between troubleshooting I hope we get the ans( Actul problem we are seeing in the router's that we have 2 ports on active routers and 2 ports on standby router , but we are not seeing muticast on 1 port on standby router where as all other 3 ports are seeing multicast packets) [code]
I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
I'm looking to try and implement ipv6 HSRP on a series of IOS-XR Routers running 4.2.1 following on from successfully setting up IPv6 HSRP on a few cat6509s on VLAN Interfaces in other parts of the network. I have entered the "router hsrp" configuration menu and gone into the interface in question that I'm looking to setup with IPv6 HSRP. Unfortunately, there version 2 or address-family ipv6 commands are not available.
if the above design is acceptable how does the routers know which one is active and which one is standby ? if we need a direct connection between two routers they have to be on a seperate subnet and routers dont allow broadcasts - so how will hsrp work on routers ?
We have two numbers of Cisco 4900 ME Switches. Basically want LAN failover from these devices. There are about 400 users in our network. I have attached rough network topology for your reference(I am not good at Microsoft Visio). Need to know implementation of the HSRP in these switches. Two distribution switches(Cisco 4900 ME Switches) are connected to 4 Access switches and these are connected to the LAN.
i have 2 cisco 7604 distrubution routers .Both routers are running 310 hsrp groups.
Sundenly there is hsrp flapping which causes high CPU.
What is the limitation of HSRP group on cisco 7604 router .Below is the show ver from the router
----------------- show version ------------------ Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRC2, RELEASE SOFTWARE (fc2)
I currently use L3 switches as edge routers to my WAN. I want to use a pair of 3560x switches with IPbase to provide a failover path to my WAN using HSRP at one location but had some problems testing the configuration. My plan is use a virtual address on the LAN interface (VLANx which port gi0/1 accesses) and the WAN interface (VLANy which port gi0/24 accesses). I want switch 1 to be primary since it will have an IPS attached to it, and switch 2 will be backup and used only when switch 1 or the IPS requires maintenance. On both the LAN and WAN sides there is no advanced routing going on, the various hosts just depend on the availability of their respective default gateways, so HSRP should be sufficient to provide a failover in either direction.
In my testing I got 1 or the other link to fail over but not the entire switch. What should my config look like to achieve failover of the entire switch in the event 1 or the other interface goes down, and fail back when the primary links are again available?
n our datacenter we've implemented HSRP on 2 6500's for redundancy purposes. Both switches are connected via a trunk. When an interface is administratively brought up, HSRP becomes instable. Below some selective logging:
12:58:01.759 CET: %HSRP-5-STATECHANGE: Vlan32 Grp 32 state Standby -> Active12:58:01.919 CET: %HSRP-5-STATECHANGE: Vlan21 Grp 21 state Standby -> Active12:58:02.031 CET: %HSRP-5-STATECHANGE: Vlan42 Grp 42 state Standby -> Active12:58:02.031 CET: %HSRP-5-STATECHANGE: Vlan18 Grp 18 state Standby -> Active12:58:02.223 CET: %HSRP-5-STATECHANGE: Vlan4 Grp 4 state Standby -> Active
Basically what happens, is that both switches becomes active and thus are forwarding traffic. After a few seconds all is back to normal. It seems they are missing each others "hello messages", so the state change is in this case normal outcome. What I can't figure out', is the root cause. Since it is triggered by bringing up an random interface configured as a dot1q trunk, I'm thinking of STP limits. But the limitations I found are 10.000 active STP logical ports and 1800 virtual ports per slot. In my case this is 2591 logical ports and all the virtual ports per slot are below 1800. This suggest the switch is capable of running this set-up without a problem.
Some extra information:-Sup 720 10GE-Version 12.2(33)SXH2a-No Vss used-No drops on trunked interfaces between the 2 core switches-83 standby groups (max256) -R-PVST
I just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
I have a new 3560G to set up a small network for a remote site. I configured the vlan and an SVI as the gateway. The switch is also the DHCP server for the LAN. I configured Gi0/2 as L3 port, connecting to the nearest neighbor. My network runs EIGRP so i advertised the routes into the EIGRP process. The switch forms EIGRP neighbors and learns all routes in the enterprise network. The problems I'm having now are: 1. The switch learns all routes in my enterprise LAN and can ping devices in the enterprise LAN, but I can’t ping any interface on the switch from the enterprise LAN. 2.
I have two 4503 switches connected individually two 5510 Asa. My web server is under 5510 dmz interface. From Two 5510 Asa dmz interface there are two cables connected to two individual server farm switches.The web server in connected to this server farm switches.My local lan in connected to a cisco linksys switch. from that two cables are connected two individual 4503 switches on same vlan. i configured hsrp on this vlan. i pings the web server from local lan. when i unplugged one cable from Primary switch then it take 7-8 request timeout to recover into Secondary switch. it takes about 40 sec to switchover. it takes too much time. i also tune the timers but no luck. My Primary switch is also a Root Bridge.
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
Had a Sev 1 issue today. We have a bunch of Nexus 5ks connecting to some HP C7000 Chassis for the use of Virual environments. Engineers build and tear down servers during the day, however today, an engineer configured a virtual machine accidently with its IP address as the default gateway. Each pair of nexus switches has one physical SVI per vlan and a HSRP address for the vlan. Of course this engineer configuring the server IP address as the HSRP address killed the vlan... which lead me onto think... are they are tried and tested techniques to protect this from happening on the switch. Enforcing the ARP/MAC of the HSRP address and not allowing it to change or any other device to change it?
I have a paif of nexus 5548 configured VPC using the mgmt interface as heartbeat and 2x10G as peerlink. Peer-gateway is also configure on the vpc domain. I have 2 FEX straight thru connection to each Nexus'es. Created 2 VPC and both are up and no suspended vlans. Allowed VLANs in peerlink is 10,20,30,40 and 50. I configure SVI for VLAN 10 on both nexus 10.10.10.100/24 and 10.10.10.101/24 respectively. The problem is when I create HSRP on this VLAN 10 (vip 10.10.10.88), the hello packets are not heard by both nexus, thus both Nexus are acting as active with unknown standby. I can ping both vlan 10 from each Nexus. I tried deleting and putting back the config but no luck.I tried creating another SVI vlan 20 on both nexus and form hsrp, result is same as in vlan 10. I am running version 5.1 release on both nexus.
I just started a evaluation license for IP Base on my 3850 switches. But i can't configure HSRP cause the commands are not there (I rebooted allready). Do you need enterprise for HSRP on the 3850?
I have a few old 2600 routers (2621, different IOS's) which I'm now replacing for new one's from the 2900 series (2901, Version 15.1(4)M4).In my configuration I have two IP addresses in my LAN interface and I have HSRP configured within the secondary IP subnet range. It would be something like this:
interface GigabitEthernet0/1 ip address 172.x.x.x x.x.x.x secondary ip address 10.z.z.z z.z.z.z
[Code].....
Now, in the new 2900 routers, my interface configuration hasn't changed however I can see that the hello packets are now sent with the source within the respective HSRP IP subnet so I had to edit my acl for that:
It looks like both my HSRP Interfaces (VLAN 600 & 700) cycle through standby --> active ---> speak continuously on one of the two switches. What can be causing this?
*May 4 06:41:24.883: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Speak -> Standby *May 4 06:41:33.671: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Standby -> Active *May 4 06:41:33.671: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Active -> Speak *May 4 06:41:34.251: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Speak -> Standby *May 4 06:41:47.691: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Standby -> Active *May 4 06:41:47.703: %HSRP-5-STATECHANGE: Vlan700 Grp 0 state Active -> Speak
