Cisco Switching/Routing :: Configure VLANs On SF 300 To Work With 2960S
Sep 21, 2011
make a couple of SF300 switches to work properly with a C2960S-48TS-L that acts as core switch/basic router. I can't seem to figure out how to assign VLANs correctly in trunk and access mode on the SF300. The 2960S are a no brainer with IOS commands but the webgui in the SF300 is a pain.
I've configured the 2960S with 3 VLANs and I would like to have the SF300 switches connect to the C2960S-48TS-L through VLAN trunk and then configure the ports on the SF300 switches to belong to the assigned VLANs of my choosing. I would also like to have all the SF300 switches management interface in VLAN 50.
I've partially described the enviroment below.
VLANs
Data VLAN 10: 192.168.10.0
Management VLAN 50: 10.20.30.0
Voice VLAN 100: 10.10.10.0
[Code].....
View 5 Replies
ADVERTISEMENT
Oct 2, 2012
This is the deal, I used Acronis for imaging workstations. Obviously when I do that it drags everything down to a halt, as all the ports are being flooded with packets. So what options do I have to image (as opposed to doing it after hours or try to plug all the computers into one isolated switch? = )
VLAN 1 has well everything in it, PXE server, DHCP server and workstationsVoice VLAN 100 is on every trunk or connection a workstation would be attached to.
There is another equipment I'm not illustrating... although a part of me wonders if my topology is correct.
In any case, I've read about IGMP Snooping, CGMP, etc-- but I think the 2960S are only capable of IGMP Snooping.
And from there I'm a little confused about configuration of IGMP...
View 2 Replies
View Related
Feb 17, 2013
We need to give differentiated internet access to three VLANs. Each one of this VLANs is used for totally different purposes, so traffic between the VLANs is not allowed. Each VLAN has its own internet access provided for the data center using one fast ethernet connection.
We're thinking about using cisco 2911 for Internet access, VPN and firewall. I suppose that best option for VLANs is using Catalyst 2960S or a swithing module for the 2911, but these two options are too expensive for us. We're thinking about using swtiches from the SB series (maybe a SG-200).
We're totaly newbies to VLANs so we have many doubts. This are our questions:
1) The 2911 has three on board ethernet interfaces; we have three VLANs and three internet connections, so we need to use HWICs to get three more ethernet ports. That's right?
2) We need three HWICs or there is some kind of HWIC with more that one ethernet interface?
3) The routing solution is to assign static routes in the 2911 for each interface connected to a VLAN through a 2911's interface connected to internet?
4) Simply connecting three different router interfaces with three different switch ports, each one of them assigned to one of the three different VLAN, are we going to get internet access for all devices in those VLANs? or do we need to configure something else like trunking, VSIs...?
5) Can we achieve our goals using the SG-200 switch?
6) We have the chance to use older routers, is this possible? We're specially interested in knowing if a 1841 or a 2801 router could be used for this setup.
7) This is not a production environment so we can use refurbished equipment.
View 4 Replies
View Related
Dec 20, 2012
Recently I'm working with my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET,This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.Access-list 100 permit ip any any dscp default,class-map match-all QoS_Floor_Limit, match access-group 100.
View 1 Replies
View Related
Oct 28, 2012
I have recently split the voice vlan (10) from the data network (1), and am wondering why my catalysts and router do not require an interface Vlan10 statement. In the past I used OpenBSD boxes to do the routing, and I first needed to configure vlan 10 on the interface before I could get inter-vlan communication to work. With these Cisco devices it works, and I am wondering if it is because of VTP, for the fact that the ports maybe just pass all traffic, or is there some other explanation? Below is the setup, and firmware is up-to-date on all of the devices.
When I plug a phone into the POE SGE, the phone turns on, obtains an address on the proper subnet, and conversations are clear (whereas without the ip nat inside on the new subnet the calls had a lot of static). Possibly the reason that it works is because the phones properly create the tcp/ip packet, and it hops over the trunks and creates the states so that traffic routes back properly. I will install wireshark to see exactly what is going on, but is there a simple explanation that I am overlooking?
View 1 Replies
View Related
Aug 8, 2012
Just I have upgraded some 2960S to IOS 15.0(2)SE from a IOS 15.0(1)SE3 and the catalyst don't switch any IPv6 traffic. Don't work any RA and also don't work any unicast IPv6 traffic from any interface. I can see some references to IPv6 changes in the FHS (First Hop Security) in the Release Notes, but no any reference to changes in the configuration.
The switches don't have any IPv6 specific configuration and the sdm is the default templata. Returning to 15.0(1)SE3 everything work ok.
On Catalyst 2960, and 3560E this IOS version seem to work fine with IPv6.
View 1 Replies
View Related
Apr 22, 2013
my client to setup their network and he want me to limit user access internet bandwidth to 2 Mbps and the topology show below.
Users ---> Switch ---> NAT Router ---> (int gi1/0/24 - qos apply) Edge Switch ---> INTERNET ROUTER (12Mbps) --->> INTERNET
This is my configuration, but it doesn't work, the end user still able to get more than 2Mbps internet speed.
access-list 100 permit ip any any dscp default
class-map match-all QoS_Floor_Limit
match access-group 100
!
!
policy-map QoS_Floor_Limit
[Code]......
View 6 Replies
View Related
Jun 5, 2013
After i have already configured my cisco switch 2960 , i configured my console as the below [code] after i reboot my switch , i found that the switch asked me for username . However i did not configure username , how can i solve this problem , without password reset . I have already configured 15 switch , 100% this problem will be in all switches.
View 19 Replies
View Related
Jan 20, 2013
I have hybrid network in which I want to configure VLAN on Cisco 2960 S switch. I have unmanged switch where my DHCP server and other servers are connected. Now I created two VLANs on cisco 2960S and they don't talk each other, but as soon as I connect unmanaged switch to 2960S switch, both VLANs start communicating which I don't want. I want to listen server traffic from unmanaged switch from both VLANs but simultaneously I don't want to communication between two VLANs.
View 10 Replies
View Related
Jan 15, 2012
I am trying to configure etherchannel on 2 2960S connected by a flexstack with 2 ports g1/0/52 and g2/0/52 on each 2960.
these switch are connected to a CAT4500, I know that I can only use LACP because of cross-stack but when I force the switch to use LACP witch channel-group 2 Mode active the switch do this :
%With PAgP enabled, all ports in the Channel should belong to the same switchCommand rejected (Port-channel2, Gi1/0/52): Invalid etherchnl mode
% Range command terminated because it failed on GigabitEthernet1/0/52
I don't know how to bundle the 2 ports on the 2960 stack. each time I use : channel-group 2 mode on there is no error
but the switch do this :
*Mar 1 00:45:32.290: %EC-5-CANNOT_BUNDLE2: Gi2/0/52 is not compatible with Po2 and will be suspended (trunk mode of Gi2/0/52 is dynamic, Po2 is trunk)
*Mar 1 00:45:32.531: %EC-5-CANNOT_BUNDLE2: Gi2/0/52 is not compatible with Po2
[Code].....
View 9 Replies
View Related
Jul 4, 2012
upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies
View Related
Mar 27, 2012
I have came across this topic, and I am wondering if this images can be uploaded to any 2900 series switches or not, and if this will work as access port for more than vlans. URL...
View 2 Replies
View Related
Mar 5, 2013
I have problem with IPV6 connectivity, i have two Cisco 3550 switch and they are connected over a trunk link. The ios is c3550- ipservicesk9-mz. 122- 44.SE6 , I have configured vlans on both switches and i numbered one vlan to vlan 91 ,they can ping each other when i configure ipv4 on both vlans so trunk link is functional, but when i m using IPV6 they can't ping each other!! they can only ping their own ip address not each other. [code]
View 11 Replies
View Related
May 1, 2012
I can't seem to find any info on how to configure 2 DHCP server pools on a C3750, to use with 2 user vlans. The purpose is that users in vlan 1 should get an IP address from DHCP server1, and users in vlan 2 should get an IP address from DHCP server2. Both DHCP servers are configured in a stack of C3750 switches, which acts a a L2 switch.
View 2 Replies
View Related
Jul 7, 2012
How to configure traffic flow between computers inside VLANs and a routed port? Here is the setup details:
1. Switch 3750-X
2. VLAN 100 - ( SVI IP address 192.168.100.1 /24)
3. VLAN 200 - ( SVI IP address 192.168.200.1 /24)
4. routed port gi1/0/48 (IP address 192.168.150.1 /24). Note: this port is directly connected to a firewall ASA 5520 port IP 192.168.150.100 /24
Ip routing is enabled on the switch and inter vlan traffic is flowing ok. I can ping the routed port gi1/0/48 from any computer connected in the VLAN 100 or 200. For example computer with IP 192.168.100.25 can ping the routed port 192.168.150.1. Switch can ping firewall port 192.168.150.100 and the 'sh ip route' command shows the network 192.168.150.0 /24 as directly connected network.
any computer in the two VLANs CANNOT ping firewall ASA port 192.168.150.100 Is it because inter VLAN routing does not work with a routed port on L3 switch? I looked up fallback bridging, but it is meant for non IP traffic.The goal is I am trying to set the ASA port as an internet gateway for VLANs.
View 4 Replies
View Related
Jan 31, 2013
How to configure a 4500X with a GLC-T SFP so that it will work at 100M.The data sheets say it will work at 10/100/1000 but Im not seeing that happen can't set the speed and it doesn't negotiate with anything at 100M it will only work with auto to another switch set to auto and supports 1000M.
View 6 Replies
View Related
Mar 5, 2012
I have a Cisco 2940 switch and a Cisco 1841 router. I want to build two different VLAN networks on the switch, which do not have to communicate one with each other, but those VLANS should communicate with the router.
I read a lot of articles, i tried to configure properly the switch and the router but i still don't get them work.
I set on the switch, the GigabitEthernet 0/1 port to Trunk port and i had to set it a native VLAN. The problem is that only from that native VLAN, i can ping the router.
View 17 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Mar 23, 2013
I need to enable multicast routing on 2960s but the command "ip multicast-routing" isn't available on my release (12.2.(55)).
From which release this command is available?
View 1 Replies
View Related
Oct 8, 2012
I have C2960S-48FPS-L and C2960S-24TS-S both of them are using C2960S-UNVERSALK9-M image with version 15.0(2)SE on both I run "mls qos"
and on 48FPS-L I run "mls qos map cos-dscp..."on 24TS-S I cannot run it. there is no such command. there is just "mls qos rewrite..." and "mls qos srr-queue..." variants.
I thought that one image give the same set of commands...?
View 5 Replies
View Related
Jan 17, 2012
while i am configuring a port on switch .The switch reloads.After reload the show version says,System returned to ROM by bus error at PC 0x458F6C, address 0x0,show version from the effected switch is,Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1).
View 4 Replies
View Related
Dec 8, 2011
I am currently having an issue with connecting a Catalyst 2960-S switch to a Small Business SG300 switch. When I connect them they are unable to form a link. When I do a show spanning-tree it says the mst link is in dispute.
View 1 Replies
View Related
Mar 25, 2012
I read some papers about QoS. The thing is that I have to implement 30 switches with QoS to connect to a lot of Cisco IP phones. The switches are Cisco 2960S with code image "C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3". Should I use autoQoS feature or manually configure them?. How should I treat uplinks between access switchs and core/distribution? I have a lot of doubts regarding queueing, because all the info I had read its for another model/image.
View 4 Replies
View Related
May 16, 2013
I'm looking at the WS-C2960S-48TD-L and have a question about the uplink ports. Is it possible to mix 10G on one uplink and 1G on the other? The datasheet says 2x10G SFP+, 2x1G SFP so I am thinking mixing is not possible.
View 6 Replies
View Related
Nov 5, 2011
just got new hardware and decided to try the newer USB port for IOS upgrades. I could not get the switch to recognize my 2gig flash drive. Do I need a proprietary stick or special format?
I also noticed when I removed it the switches crash dump and rebooted?
View 12 Replies
View Related
Aug 18, 2012
When using dynamic configuration tools, if I choose 2960 (not 2960s), I have the option to choose RPS2300 as redundant power, but when I choose 2960s, I cannot choose RPS2300. However, in a document describe both 2960 and 2960s, it said that RPS2300 can be used. Does RPS2300 support 2960S?
View 1 Replies
View Related
Mar 11, 2013
I would like if is possible to stack a Cisco 4900M with a 2960S. I know it is not the most common situation but i need it.
View 1 Replies
View Related
Feb 20, 2013
I would like to enable port security to hardcode the MAC address on the ethernet switch. There are 5 ethernet ports in the same ethernet switch to be assigned for one person (one note book), e.g. port 5, 6, 15, 16 and 23. The model of ethernet switch is cisco 2960S and one MAC address is configured on 2960S.
1. Does 2960S support this requirement to allow input the same MAC address to 5 different port?
2. If yes, can ethernet switch "smart" enough to forward the packages to "active" ethernet port which is connected to notebook and the rest of four ports are inactive.
3. if no, any solution or any work around to achieve this requirement
View 5 Replies
View Related
May 11, 2011
We are designing a LAN Network for ourselves.The proposed design is as follows:
4 x 2960S switches in a Stack Access-Stack-I 4 x 2960S-PoE switches in a second Stack Access-Stack-II
2 x 3750X switches in a Stack Core-Stack
Now I would like to connect it in the following manner ?First,I would like to use EtherChannel using the 10Gig LinksSecondly, I would like to use Cross-Stack EtherChanel too.I have given a graphical illustration of the connectivity Now my Qs: a) Will the 2960S supports EtherChannel using the 10G links and the 3750X too... b) Does the proposed solution will work... or It will have any problems.
View 4 Replies
View Related
Jan 29, 2013
I have two switches (2960S's) both with IP Phones on VLAN100..We need to monitor voice traffic via a monitor port on SW1 of all VLAN100 traffic on both switches.The following is what we have configured, but we cannot see VLAN100 traffic on SW1
According to Cisco doco you cannot have a SPAN and RSPAN on the same session, however since these are two sessions on SW1, I would have thought it to be OK.
View 4 Replies
View Related
Apr 29, 2013
I have a running setup having 2 Cisco 2960s 24 TS switch with Stack configuration. Now I want to add one more same Cisco switch. My questions are:-
1) How can I do this...(Should follow the same process as I did before.
2) Could I do this without impacting the service. i.e. without rebooting the switch.
3) What should be the connection archiecture as of now since there is two switch so it is connected 1 -1 and 2-2. but for 3 switch should we require to change the connectivity.
View 1 Replies
View Related
Jul 21, 2012
i did on cisco 2960S switch at user ingress interface. but the marking is not showing in show policy-map interface gig 1/0/10 interface and ACL is not showing any match.
I also had a config reference from 2960S cisco guide.
access-list 103 permit tcp any any eq 80
access-list 104 permit tcp any any eq 23
access-list 105 permit icmp host 172.24.68.4 any
class-map IN_HTTP
match access-group 103
class-map IN_TELNET
match access-group 104(code)
View 1 Replies
View Related
Feb 8, 2011
We have seen high CPU utilization on some Cisco switches of type 2960S. Also we got info, that applications are running with poor performance or with interruption.Following IOS is loaded: C2960s-universalk9-mz.122.55.SE
View 9 Replies
View Related
