Cisco Switching/Routing :: Configure 2940 Switch To Work With 1841?
Mar 5, 2012
I have a Cisco 2940 switch and a Cisco 1841 router. I want to build two different VLAN networks on the switch, which do not have to communicate one with each other, but those VLANS should communicate with the router.
I read a lot of articles, i tried to configure properly the switch and the router but i still don't get them work.
I set on the switch, the GigabitEthernet 0/1 port to Trunk port and i had to set it a native VLAN. The problem is that only from that native VLAN, i can ping the router.
View 17 Replies
ADVERTISEMENT
Apr 24, 2012
I'm trying to configure a 2940 switch to trunk. I just can't get it to work.On the interface I have added: switchport mode trunk The default is encap for this switch is dot1q, so there is no need, or ability to add/change the encap mode. Also all vlans are being allowed by default. I still can't get any port to trunk. Need to get G0/1 to trunk, have also tried to trunk f0/6 to the switch in my office. Also can't find the command to change the management VLAN. I do not use vlan 1 for management. Can I change the Mang VLAN on this switch?
View 7 Replies
View Related
Mar 12, 2012
Having an issue with two Cat 2940, they have fiber 100Base-TX. Added a new Cat switch (the second on the VLAN), the existing Cat switch drops the fiber connection.
View 6 Replies
View Related
Mar 3, 2012
I have this strange problem with my Macbook pro, when I connect it to my cisco 2940 8 port switch then I can reach my ISP (websites eg. google.com) in like 2 minuttes, then something is happening on my router, because suddenly I can´t reach my ISP
This is what I have found out so far:
1. when I lose connection to my ISP then I can only ping internal ip addresses eg. another computer in my network
2. if I renew my ip address on the Macbook then it works again in 2 minutts, then the same happens again. This is my network setup:
Router -> Switch 1 -> Switch 2
I also know that it is not the Macbook, because it have got a new motherboard, and it have been reinstalled
also if I use the Macbook on a other network then it works fine.
All my other computers ( windows and linux ) works fine, no problems.
To me it looks like it is a Nat and/or DNS problem, but I can´t fine out what it is.
View 7 Replies
View Related
Jun 6, 2013
I have two switches (sanitized configs attached) and I am trying to bond int gi0/1 and gi0/2 between the two. Then I need int gi0/3 back to the main LAN switches. These are new Vlans created 982 and 983 for these switches. Question #1: do the configurations look correct? I haven't placed any laptops on the interfaces to test interconnectivity yet but I am wondering if it will work with no default routes.
The admin team needs these switches at location A for setup then they will be moved to Location B. The only thing that sucks for me is that the network admin before me created gateway interfaces for all the local Vlans on a main router as sub interfaces. For example, for these two subnets, I need to create subinterfaces below (at location A), which is why a gave the Vlan on the switches, ip addresses.
interface GigabitEthernet0/0.982
encapsulation dot1Q 982
ip address 10.98.2.1 255.255.255.0
ip flow ingress
no cdp enable
service-policy input mark-mplsqos-in
interface GigabitEthernet0/0.983
encapsulation dot1Q 983
ip address 10.98.3.1 255.255.255.0
ip flow ingress
no cdp enable
service-policy input mark-mplsqos-in
When I move the subnet to location B, I will also move the gateway. These two switches will be used mainly for a VMWare and HyperVisor environment so Vlan 982 is for VMA network and Vlan 983 is for management. The admin tells me the software needs to tag the packets, I am not sure if I care as the switches should handle that also.
View 1 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Oct 22, 2012
I have a Cisco 1841 router connected to a Cisco 2960 switch.Users behind the router can't access the internet but when someone is directly connected to the switch with his PC and uses the IP Address found on the WAN port of the router, he's able to go on to the internet. [code]
View 4 Replies
View Related
Feb 18, 2013
We are using Cisco Router 1841 and users reporting issue related to VoIP. After investigation, seeing input errors on Router LAN interface, but there is no error on connected switch interface. [code]
View 2 Replies
View Related
May 26, 2013
We have a setup of a firewall in between my Cisco 1841 router and Switch.
Cisco Router --> Meraki Firewall--> Switch
Client VPN is configured on the Meraki Firewall but then for the outside users to client vpn in to the network, I have to port forward or open the ports 500 and 4500 to the IP address of the Meraki Firewall 192.168.1.90. [code]
View 4 Replies
View Related
Feb 2, 2012
I am trying to find out if its possible to use an existing CISCO 2940 Switch that we have here at our office as a hub? Im sure that borders on insane however, let me break down what we have currently and what I'd like to do.
We currently have a very nice setup here at work, with no problems whatsoever, however; we hired a new person and brought in some new printers and we are running out of wall jacks. Rather then run all new cabling and adding new outlets/faceplates etc... We were just gonna go purchase a simple Netgear 5 port switch/hub from the Local Comp store here in town. We found in our server room a what appears to fully functional and operational cisco 2940 8 Port Switch with a Gigabit port.
All IPs in the office are assigned via DHCP, so....on to the meat of my question -- I tried to plug this into our network and I can't get any connectivity out at all. All the ports light up green etc when I plug in the comps but they aren't pulling valid IPs.
I want to reset this thing and start from the ground up, I am not scared of going into the IOS and modifying what needs to be done...as long as I got a good enough walk through.
View 6 Replies
View Related
Jan 31, 2013
How to configure a 4500X with a GLC-T SFP so that it will work at 100M.The data sheets say it will work at 10/100/1000 but Im not seeing that happen can't set the speed and it doesn't negotiate with anything at 100M it will only work with auto to another switch set to auto and supports 1000M.
View 6 Replies
View Related
Sep 21, 2011
make a couple of SF300 switches to work properly with a C2960S-48TS-L that acts as core switch/basic router. I can't seem to figure out how to assign VLANs correctly in trunk and access mode on the SF300. The 2960S are a no brainer with IOS commands but the webgui in the SF300 is a pain.
I've configured the 2960S with 3 VLANs and I would like to have the SF300 switches connect to the C2960S-48TS-L through VLAN trunk and then configure the ports on the SF300 switches to belong to the assigned VLANs of my choosing. I would also like to have all the SF300 switches management interface in VLAN 50.
I've partially described the enviroment below.
VLANs
Data VLAN 10: 192.168.10.0
Management VLAN 50: 10.20.30.0
Voice VLAN 100: 10.10.10.0
[Code].....
View 5 Replies
View Related
Mar 23, 2011
I have downloaded the 90 day ISE evaluation to a vmware platform I have it successfully authenticating local user(s) onto a Cisco 2940 device (12.1) IOS I am trying to follow a TrustSEC design guide [URL] but my LAB 2940 does not support many of the commands shown in this document What I want to try to do is be able to familiarise and demonstrate in the lab the use of ISE to control access to the network using 802.1X and or VPN access from remote vpn clients?
View 2 Replies
View Related
Dec 12, 2012
Does the port adaptor PA-MC-2E1/120 work with the Catalyst Switch 6506E (Sup Engine: 720-3B)? We have bought a Enhanced FlexWAN card for this port adaptor.I read through the cisco website and seem to get confusing answers whether they are compatible.
View 1 Replies
View Related
Aug 24, 2011
I got one SF 300-48 layer 3 switch I tried to configure to use it in the office network.Unfortunately I'm unable to configure the VLAN settings.I need port one for input(VLAN2),port 7-15 for another vlan(vlan3) also need to connect with the vlan 4.port 15 is another vlan(vlan4) this is for wireless.Other ports are static.It doesn't get any connections with other vlans.I wish to know how to configure vlans in GUI mode.I tried , But I can't get the Vlan setting correctly.Also,I need to know how to communicate both vlans in GUI mode.
View 8 Replies
View Related
Nov 7, 2011
configure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies
View Related
Dec 12, 2006
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies
View Related
Jan 14, 2013
I am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies
View Related
Jun 7, 2012
configure QoS on 3560 switch i have taken the template from cisco configuration guide since we have different QoS configuration on each model.
below is the configuration :
configure terminal
mls qos
end
mls qos map cos-dscp 0 8 16 26 32 46 48 56
no mls qos srr-queue input cos-map mls qos srr-queue input cos-map queue 1 threshold 2 1 mls qos srr-queue input cos-map queue 1 threshold 3 0
[code]....
Currently all the cisco phones are connected to this switch and configuration with only one vlan that is voice vlan .
1) what is the outcome of this configuration , i mean, what will be the expected output ? end of the day we need to prioritize the voice traffic but why other commands including threshold and buffers are mentioned with respectives queues , if I need to explain that what am i expecting out of this configuration ?
2) this is LAN QoS which i understood but again , do i need to configure policy-map along with class-map which is MQC on this switch ?
3) i have edge router where i have MQC already configured but confusion with this switch which is working as a Access switch .
4) I referred the cisco QoS document for the respetive model whereas we have policy-map configured on the same switch with class-map .
My understanding is if we have configured the LAN QoS , and mapped the CoS value with DSCP , we need not to have MQC.
View 4 Replies
View Related
Apr 17, 2012
We have over 30 Cisco 3560 switches and over 10 VLANs on our network. In our example, VLAN 10 on switch IP 10.0.20.150 works fine and VLAN 10 on switch IP 10.0.20.24 doesn’t work. The below are both switches show vlan. url....I can’t tell what causes the problem and how to fix it. VLAN 10 on Switch 10.0.20 24 doesn’t work. [code]
View 8 Replies
View Related
Sep 16, 2011
Right now I have it connected like this: Internet-> SURFboard SB6120 Modem -> DGL-4100 Router (modem in the WAN port, 3 internet connections plus the switch in the LAN ports) -> DGS-1008G Switch (2 other internet connections connected to this, as well as an Xbox 360).The problem is that everything connecting to the router works, and nothing works on the switch even though the power light is on (however, the port on the router that is receiving the switch is not lit up). I'm guessing this is because the router only assigns as many IP addresses as it has ports or something.
View 10 Replies
View Related
May 13, 2012
We are using cisco ME 3400 E series switch. Which port we can use as CFM port ? We configured CFM in gig port.Is all the ports will act as CFM port or any separate CLI command is there for enable ?
View 0 Replies
View Related
Aug 19, 2012
I want to configure Cisco 3560 SWITCH with IP cameras. I need to configure the ports connected to Camers. IP addresses to the Cameras has been assigned.
View 1 Replies
View Related
Mar 18, 2010
am having a switch 3860 it is configured dhcp , dns i want to change those dhcp , dns, what are the command that is use to reconfigure it
View 1 Replies
View Related
Mar 8, 2012
Today in my rush to get home I plugged in a new 2960 stack and did a little bit of very basic configuration, but no passwords were set. I tried to telnet in and the message says that a password is required, but none is set. I tried the SDM as I hadn't turned it off yet and it is prompting me for a user/pass but I have no idea what to put in there. No console is available, it's a new office so no employees around either.
View 14 Replies
View Related
Jun 2, 2013
i configure the uplinks as etherchannel, i configure two svi interface on core switch int vlan 51(192.168.51.1) and int vlan 50(192.168.50.0) for this two svi int i configured two dhcp pool , when any of the pc is requesting for dhcp add i am getting dhcp request failed/
View 7 Replies
View Related
Jun 5, 2013
After i have already configured my cisco switch 2960 , i configured my console as the below [code] after i reboot my switch , i found that the switch asked me for username . However i did not configure username , how can i solve this problem , without password reset . I have already configured 15 switch , 100% this problem will be in all switches.
View 19 Replies
View Related
Apr 29, 2012
I have Cisco 3560X L3 switch and i need to configure DHCP on this switch. I have already configured below mentioned VLANs
VLAN 10 - 192.168.8.254 (USER VLAN)
VLAN 20 - 192.168.152.254 (REMOTE & VPN USERS VLAN)
VLAN 30 - 192.168.0.254 (SERVER VLAN)
After configuring DHCP, all the users needs to get IP from USER VLAN and all the servers should get IP from SERVER VLAN. If yes, what are the steps as I am very new in this kind of configuration.
View 5 Replies
View Related
Jan 20, 2013
I have hybrid network in which I want to configure VLAN on Cisco 2960 S switch. I have unmanged switch where my DHCP server and other servers are connected. Now I created two VLANs on cisco 2960S and they don't talk each other, but as soon as I connect unmanaged switch to 2960S switch, both VLANs start communicating which I don't want. I want to listen server traffic from unmanaged switch from both VLANs but simultaneously I don't want to communication between two VLANs.
View 10 Replies
View Related
Jan 9, 2012
I would like to know if ip helper-address feature is working on a layer 2 switch (2950,2960) or you should use a Layer 3 switch to do that?
View 7 Replies
View Related
Feb 11, 2012
With out using any server, will DHCP be configured in cisco 2950/2960 switch?I man cisco it self should work as a dhcp server also.
View 10 Replies
View Related
Nov 17, 2011
I will be start with the disclaimer that I am very technical, but a huge novice to the enterprise-grade Cisco swtiches.
How IOS software versions are licensed on a Catalyst 4507 switch? I am very confused at this point.
For example, if I buy IOS Enterprise Services for a new Catalyst 4507 switch, what form does the software license take? Is the license embedded on the switch? Does it come as an e-mail or certificate with a PAK? Does it come on a CD?
We sold a 4507 with Enterprise Services to a client, and they are saying they don't have the right IOS version installed. I assumed there must be some license key they needed, but the Cisco licensing help desk does not seem to indicate there are any licenesable items on our sales order number (even though IOS Enterprise Services is a line item on the sales order).
I know there was a disk that came with the switch with an Enterprise Services .BIN file on it, but I had assumed that was just a software version image, similar to the images I can download off the Cisco website. But is this actually the license key?
Since I can download image files off the Cisco website, I assumed there must be some other key needed to activate the license.
Switch is Catalyst WS-C4507R+E
Redundant Supervisors are WS-X45-SUP6-E (Supervisor 6-E)
View 2 Replies
View Related
Mar 19, 2012
I haven't worked with infrastructure much lately but planning on replacing a Dell switch used for a small iSCSI SAN with a Cisco 3560x. Switch is sstorage ONLY, network handled through different switches. I believe I want to disable spanning tree and configure trunking for the 4 GB ports connected to the storage array. The switch is providing connectivity to SAN via multiple GB connections and then also multiple GB connections to 3 Vmware hosts.Can you look over the changes I made to config below and let me know if I am on the right track.
I also plan to add a second switch later with the 10GB modules to interconnect for redundancy (but not worried about that part for now). I do not plan on using jumbo frames.
Here are my questions
1) Is the best way to globally disable spanning tree for the switch?
2) Did I trunk the ports correctly below?
3) Should I apply any specific SmartRoles to the 4 SAN NICs (GE1-4) or to host NICs (GE13-20)?
4) Anything additional I should do to handle iSCSI data?
Here is a copy of the config so far with my changes marked in RED.
storage1#wr tBuilding configuration...
Current configuration : 1696 bytes!version 12.2no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-
[Code].....
View 2 Replies
View Related
