I have cisco 2504 WLAN controller with 7.4 IOS. My query is can I configure the MAC authentication with certificate based. And without using any external servers like Radius, ACS and LDAP.
May I know, If there is a option on WLC…
When I get the web authentication dialog from 1.1.1.1 it starts of with a certificate error. Is there a way to prevent this certificate error while using the self signed certificate? I have not been successful installing certificates on my WLC - problems with OpenSSL and others. Want to get this deployed but don't want users to have to encouter that error.
View 1 Replies View RelatedWhat are the possibilities for configuring a WLC to authenticate WLAN users based on their Active Directory user account?
Is this possible by setting up local EAP on the WLC?
I’ am looking for a solution where there are no changes to the Domain Controller involved and also no setting op IAS/RADIUS.
WLC:2504
We use a combination of Cisco ACS and Cisco catalyst 3560 switches for network authentication and authorization. Clients (Windows XP) have a certificate installed which will grand access to the network and put them in the correct VLAN. So far, so good. Some users are testing with Windows 7 in the same set-up as above and run into strange behaviour. The problem is that after a random timer the machine gets de-authenticated and nothing besides a reboot works to get the computer authenticated again (from a Windows point of view). It looks like this only happens to users who are using a certificate to authenticate, Windows 7 MAC bypass users have no such problems. If it occurs, the following logging appears in ACS: [code] We are using ACS 4.2(0) Build 124 and 3560-48PS switches with IOS 12.2(55).
View 4 Replies View RelatedHow can I setup the WLC to accept authentication based on the device itself and not a user?
View 7 Replies View RelatedI want to configure IEEE 802.1x port-based authentication on cisco switches, preferable 2960 series. Which models support this feature?. I have try with some older switches but it doesn't works properly on everyone. I have upgraded them whitout better results, there is namely an issue with TLS handshaking on some switches which produces authentication to fail.
View 1 Replies View RelatedI have a cisco wlc 2504 is deploying authentication services to guest users toward a portal web customized and configured. I need to install my certificate verisign (certificate.cer) in to cisco wlc because my users don't like the page no trusted (The wlc is showing me ''There is a problem with this website's security certificate'') when they are trying to access to ssid to users guests.
View 2 Replies View RelatedI have initially configured 2504 controller with necessary parameters. & we have LAP1131AG access Points. we have connected 2 Nos. of access points in network. we are getting Both AP connected with controller,Whenver i am trying to connect with this wireless network though SSID( currently, open authentication), laptop's not connecting with it. it shown error that " Windows was unable to connect to SSIDname "
View 4 Replies View RelatedWe have a WLC 2504, since a few months, it was working fine, we have a guest Wlan configure with web authentication and the DHCP scope for this in the WLC. The problem today is that its no redirecting the web browser to 1.1.1.1, we try it with 3 laptops and they recieve a correct IP from the DHCP but still can not get redirect to the web authentication portal. Have the default configuration Internal (Default).
In laptops we check the firewall, dont have a proxy activate and have google DNS.. 4.2.2.2 8.8.8.8. In fact this laptops connected to this ssid before.
I am planning to migrate from an old 4400 to a new 5508. I am happy with migrating the access points but I need to know if I can migrate the web authentication certificate used for guests.The new WLC will have the same virtual interface and DNS name to match the CN on the current certificate. Will this work or will I need a new certificate?
View 2 Replies View RelatedI configured the 2504 with 2 SSIDs for staffs and guests.I also configured the Lobby admin with web auth. But if a guest wants to connect our wireless he/she has to enter the PSK key and then only they are able to connect with the user id and password given by Lobby admin. Can we avoid this key and let the guests connect straightaway with the web auth?I’m planning to configure 802.1x & Radius dual authentication for staffs SSID..
View 5 Replies View RelatedI have 2504 WLC with a few access points. the problem is when the PC's go in sleep mode, the users have to re-authenticate when they log in again Is there any way to let the PC's automatically re-authenticate without the user having to type in the credentials again?I have web authentication configured for this SSID and authentication is using the WLC local Data base.
View 6 Replies View RelatedHow to implement certificate based 802.1x authentication network access using ACS5.3 & external identity store as AD.
View 13 Replies View RelatedWe are planning to implement Cisco wireless in our central office and branch office using Cisco 2504 WLC and Cisco 1602i Ap. Our branch office is connected via ip vpn and a separate broadband connection for urgent requirements. Usually all users are allowed to browse through central proxy server.I have been trying to find any possibility of giving guest access (web authentication) for branch office guests utilizing only the broadband connection which is connected to the branch office. Is there a possibility that Central WLC is reached using NAT from the BranchOffice AP and allowing guests to authenticate and surf the web at times IP VPN is unreachable.
View 4 Replies View RelatedI have set the RV042 up for QuickVPN access. The router config recommends turning HTTPS on in the firewall when using QuickVPN. The side effect to this is any web browser throws me certificate errors and warns me not to continue logging in to the router's config. How do I fix this so the browser does not throw these messages?
Router is Linksys-branded, using latest firmware for this hardware (1.3.13.02-tm)
I'm changing SSL VPN from aaa authentication to both aaa and certs, Server 08 CA, 8.2 ASA 5510, ssl client 2.5.1025 and Windows 7 users. My question is what should be the template of the id cert that I receive from CA. ,
View 16 Replies View Relatedwe are using Cisco Aironet 1130 AG and a Cisco 4402 WLC in our network. The certificate service is installed on a Windows 2008 R2 server. We use a standalone Root CA with a Enterprise Sub CA hierarchy. Issueing certificates to clients works fine. The vendor and ca certificates are installed on the WLC and the user have his user certificate. During implementation we used following document: url... Instead of Anonymous Bind, we use a service user to read in AD (works fine, too).
We use the Intel/PRO wireless utility on our Testclient and configured it for EAP-FAST and TLS. We can select the installed certificate in the utility, but when we try to connect, the utility throw the message: "Authentication failed due to an invalid certificate".We´ve logged the WLC and thats a part of the logfile (i´ve greyed out all enterprise data): [code]
I am doing a proof of concept with anyconnect and certificate authentication. with 3.0 i was able to do this with a certificate from my CA and a client cert in a smartcard. I have upgraded to 3.1 and now it doesnt work anymore ( i need 3.1 and Asa 9.0 because of IPv6 Split-tunneling).Reading the forum i got some info that the ASA cert must have a EKU value of 'Server Authentication' and the client cert must have a similar EKU (client Auth)
View 4 Replies View RelatedThe IPAD VPN works great over token, radius and local authentication. But now we need to authenticate vpn client via digital certificate (only vpn authentication between client and gateway)? I'm not sure which certificate we should buy to authenticate vpn client.The plan is to install digital certifiacte on VPN Gateway (CISCO ASA 8.0.4) and IPAD Cisco IPSec client to eliminate user/pass authentication.
View 9 Replies View RelatedI have configured SSLVPN on a asa5520 with aaa and certificate authentication.Both authentication works fine,but I find the client users can use any others' certificate to authentication,I want to binding the aaa account to user's certificate.everyone must use their own certificate.
View 1 Replies View RelatedI am using a cisco asa5520 and i have set up remote access vpn with an AnyConnect connection profile.In the connection profile i have set up that users should authenticate using both certificate and AAA.Due to a high security requirement, the user certificate is issued from a 3rd party. This is working fine and the user now need a valid certificate and a username/password to authenticate successfully.I added the CA certificate as a associated trustpoint on the ASA box to get the certificate verification working.Problem:If Jane and Joe both have a valid certificate AND a valid username/password, Jane could authenticate using a combo of Joes certificate, and Janes username/password. Both are valid (isolated), but i only want jane to be able to authenticate with her username/password and her personal certificate.
View 1 Replies View RelatedLooking for the steps to configure wired clients using certificate authentication only
- i.e., once a certificate is presented to the ACS that is issued by a trusted CA, the connection is permitted.
No need to tell me about switch configuration.
I am using wireless system with certificate athentication ( CA Server ) and RADIUS server.
I want to know if certificate is not installed and configured in wireless client laptop.
Do client get athenticate in wireless system and get access of wireless network ?
Also want to know any configuration required in WLC CISCO 4402 for authentication with CA server of client laptop.
Our ACS (5.3) has self signed certificate, we have exported it and declared it in Certificate Authorities.We have exported it to have a Trusted Certificate for client machine.
This certificat has been installed on a laptop.The wlc is successfully setup for eap (peap & eap-fast has been tested > ok)I have this error in the log:
12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in the client certificates chain.I think the Access Policies (identity & authorization) are misconfigured: [code]
Is there a way to authenticate a windows computer in ACS 5.2 for 802.1x only with a certificate.The Computer is from a different active directory than the one that is configured in ACS.I tried importing the cert into "external indentity Stores" > "certificate authorities", then setup the computer to use smart card or certificate, then selected the certificate from the other AD.when i look at the ACS log, here is the message i can see: 22044 Identity policy result is configured for certificate based authentication methods but received password based
View 1 Replies View RelatedIt,a possible configure 2 ssid with wlc 2504 and lap 1042n? It,s possible configure 2 ssid with support 802.11n?
View 1 Replies View RelatedI have WLC 2504 controller and six access points AIR-LAP1042N. I reading Cisco 2500 Series Wireless Controller Deployment Guide url...trying to set up along the lines.
It is also possible to have multiple AP-managers in a different subnet than the management interface. However, in this case, it is recommended that you disable the AP-manager from the management interface and create another AP-manager interface on different physical ports in a different subnet than the management interface. All multiple AP-managers in this scenario should be in the same subnet.
I maping management interface on physical port 1 and disabled ap-manager on it. Set up 192.168.7.0 subnet with non tagged vlan. This iface/port I want to use only for access to WLC web-interface. Then I create dynamic interface ‘dynamic1’, map him on port 2, enable ap-manager on him, and set up 192.168.110.0 subnet with vlan 10. Then I tryed map wlan1 to this iface, but I can’t because in the choice was only management iface to map wlan1.
There is three dynamic interfaces on same subnet and vlan, in example above. But when I try to add dynamic iface with the same vlan/subnet as an existing dynamic interface, I get an error, and can’t adding.
I am enabling our wireless controllers to use 802.1x authentication for our wireless clients. Both computer and user are provided with certificate from CA server.I have 9 APs and 2 controllers installed in my infrastucture, one of the controllers is working fine with setting specified above but the other one is not.Both has same configuration and both seems identical with same model and IOS.
View 3 Replies View RelatedThe problem is that with any EAP method of authentication that utilizes authentication with a certificate or smart card the switch will somehow impede authentication with the radius server. The EAP Methods I have tried on a SG-300-28P and ESW-540-24p switch are:EAP-TLS, EAP-FAST, PEAP Smart Card, I know that the radius server works because when I switch to a different switch the client works just fine, or if I keep the client on this switch and use any password method (PEAP (MSCHAPv2), MSCHAPv2, EAP-MD5) it also works. In both cases the radius server logged a EAP Timeout. Again this only happens when any EAP method or version of authentication used deals with certificate authentication.Only with the 3 Cisco small business switches we have, have I ran into this problem. The Cisco Aironet and Other Switches (by other manufacturers) work just fine.
View 2 Replies View RelatedI want to connect with AnyConnect Secure Mobility Client 3.0.2052 to ASA 5540 Version 8.4 and SSL Premium License.The clients using Maschine Certificate to authenticate to ASA. This works fine.Now I want to setup a DAP to verifiy the client against the Microsoft AD using LDAP. I configured LDAP server in ASA see:aaa-server LDAP protocol ldap aaa-server LDAP (inside) host ldap.com ldap-base-dn DC=x,DC=x,DC=x,DC=com ldap-scope subtree ldap-login-password ***** ldap-login-dn ***** server-type microsoft ,I can see that it works if I test the server via the testbotton in ASDM and I see it in CLI "debug ldap 255" also. But if I configure in DAP: AAA Attribute ID:memberOf = DomainMember I can not see any request to the LDAP server during I try to connect with the Client und the DAP doesn't match.
View 2 Replies View RelatedCurrently the ACS 5 is authenticate the iPhone/iPad by using the MAC address (which is entered manually) and AD user/password, i need to do that with certificate, so it will be scalable.
View 2 Replies View RelatedI'm trying to set up vpn with ASA 8.2(5) and Anyconnect 3.0.4235. The goal is to force user to connect from registered machines only (winXP & win7 x32 and x64). To do this, I used machine certificates issued by own CA. Certificate is installed in machine store. I use double authentication (aaa & certificates). Everything works fine, AnyConnect browses cert store, ASA validating machine certificate, then user is prompted for username/password and finally if all is correct - connection is established.My problem is, that for new installation (new host), AnyConnect fails at first connection attempt. If I use aaa authentication only, connection is established, but if I use aaa & certificates - connection fails. The appropriate .xml profile is predeployed at client host asa well as machine and root certificates.Important: When first try (aaa auth) succeded, others are always OK (with aaa. certificate or aaa & certificate authentication). Only the first one fails.The goal is to succesfuly establish connection with aaa & cert.
With DART i get:
******************************************
Type : Error
Source : acvpnagent
Description : Function: CTransportWinHttp::WinHttpCallback
File: .CTransportWinHttp.cpp
Line: 2150
[code]....
Certificate is valid for sure, and as I mentioned before, if first use aaa only, the second try is OK. At ASA with debug crypto ca 255 can't see any certificate from client.
Any instructions to configure an ASA to allow authentication by certificate only on an AnyConnect vpn?I'm running an ASA 5505 with 8.4(1) and AnyConnect 2.4.7030 on an Android phone.I currently have the AnyConnect client connecting ok using username / password for authentication.
I have loaded the company root certificate (internally generated) into the ASA "CA Certificates" and generated an Identity Certificate for the ASA.