Belkin Routers :: Play Max N600 HD F7D4401 Dual-Band Signal Very Weak?
Jun 12, 2013belkin play max n600 hd model F7D4401 Dual-Band signal very week so i need the best setup.
View 1 Replies
ADVERTISEMENT
Belkin Routers :: N600 DB Wireless Dual-Band USB Adapter / Windows 8
Nov 18, 2012I got the N600 DB Wireless Dual-Band USB Adapter in October 2012. How do I install it on Windows 8?
View 1 Replies View RelatedBelkin Routers :: Firmware Compatibility With N600 Hd Wireless Dual Band
Apr 1, 2013I have belkin n600 hd wireless dual band n router f7d8301 v1. do i need to do any firmware upgrade? should i down load and install V3 of firmware of V1 only? i want to increase / enhance the range of WiFi.
View 1 Replies View RelatedBelkin Routers :: How To Bridge N600 DB Wireless Dual-Band Router F9K1102
Dec 31, 2012Is there a way to Bridge N600 DB Wireless Dual-Band N+ Router F9K1102?
View 1 Replies View RelatedBelkin Routers :: F9L1101 N600 DB Wireless Dual-Band USB Adapter / No Internet
Nov 13, 2012F9L1101 N600 DB Wireless Dual-Band USB Adapter : recognizing and connecting to wireless network but unable to use internet. Changed static IP adress, etc but no luck. Followed instructions on support email response:
Windows XP:
Start->Control Panel->Network Connections(classic view)->Right click on Local Area connection(wired)/Wireless network connection(wireless)->Properties->Select Internet Protocol(TCP/IP)->Properties->Under General tab, choose "Use the following IP address" and type the IP address, Subnet mask and Default Gateway, DNS and press OK.
Type in the ip address 192.168.2.20
Enter the subnet mask as 255.255.255.0
Enter the default gate way as 192.168.2.1
Type in the primary DNS as 4.2.2.2
Type the alternate DNS as 8.8.8.8
Am currently unstalling and reinstalling. The network is WEP with a long alpha numeric key, which was accepted and network detected and connected. No internet. No internet. No internet.
Belkin Routers :: Update F9L1101 N600 DB Wireless Dual-Band USB Adapter From Windows 7 To Windows 8
Nov 25, 2012My new Windows 8 computer is not wi-fi capable, I bought the adapter but it only works with Windows 7, they have a link to upgrade to Windows 8 but I don't know where to go from there.
[URL]
Belkin Routers :: Connecting To Two Networks With Play Max N600 HD
Jun 2, 2013Play Max N600 HD (F7D4301) Dual network operation - on behind Belkins firewall. I have just changed the structure of my network for reasons of additional services being added. I now have in the front room the ADSL modem connected to a switch and 2 PC's. The switch is also pbugged into an ethernet plug in the wall which feeds to the other end of the house where the Belkin router is. I have all devices working on the internet correctly. The issue is getting access between the two networks and the devices on the two networks. I have added the ip addresses of the PC's to the router's LAN/Static Route, but that didn't work. The network in front room (after ADSL Modem is 192.168.1.x and after Belkin router it is 192.168.2.x. Is there a way I can allow access between the two networks between devices?
View 2 Replies View RelatedBelkin Routers :: Play N600 - No Computer Can Auto-connect To It?
Mar 24, 2013Just installed N600 Play router. All computers and phone connect fine, but computers won't auto connect after reboot or sleep. With old router this worked fine.
View 4 Replies View RelatedBelkin Routers :: Play N600 - Flashing Orange Light
Oct 11, 2012My N600 router has a flashing orange light on it. What's going on with this thing?
View 4 Replies View RelatedBelkin Routers :: Can't Connect Wirelessly To Play N600 F7D8302
Feb 21, 2013I just bought a Play N600 F7D8302. I swapped out my old Belkin router for this one. Easy swap. I went in to the 192.168.2.1 address, to look at the current wireless settings. I saw an option to use it as an access point. Not sure what I was thinking when I checked it off, but now I can't connect wirelessly, and I cant get onto the settings page again, via 192.168.2.1. My IP address has changed, and is now 50.135.82.220. I've unhooked everything and hooked it back up. I pushed the reset button on the back. I don't know what to do. How do I get it back to the way it was before I got my hands on it?
View 2 Replies View RelatedBelkin Routers :: N300 Makes Internet Signal Very Weak?
Apr 30, 2013My SURF N300 router makes my internet signal very weak, 1/10 of what was contracted but it works perfectly with the cable connected directly to the computer, how can I configure it to work properly?
View 1 Replies View RelatedBelkin Routers :: N300 Range Extender With Weak Signal
Jun 10, 2013I have a Belkin N300 Dual-Band Wi-Fi Range Extender but the signal light is always amber and I have difficulty connecting to the N300 wi-fi. Can I use a wired Ethernet cable to connect to it rather than it picking up the existing weak Wi-Fi signal?
View 1 Replies View RelatedBelkin Routers :: N600 DB N+ - Choosing Band To Use
Jan 19, 2013The Belkin N600 DB N+ Router. It has 2 seperate networks for optimum performance, how do i go about choosing which band I want to use? Under the Belkin desktop I can clearly see 2 SSID's. One shows 2.4 GHz SSID & network name and the other 5GHz SSID & network name. media. But when I pull up my wireless connections I only see 1 network.
View 1 Replies View RelatedBelkin Routers :: N750 DB - How To Utilize Dual Band Feature
Dec 1, 2012How do I utilize the dual band feature on my belkin N750 DB? Do I have to set up two separate networks? Even then how when my devices PC, iPod, gaming devices are only recognizing the 2.4GHz band network?
View 3 Replies View RelatedBelkin Routers :: Airplay Not Operational Via Cat 5 On The F7D4401
Dec 10, 2012Why does my belkin f7d4401 playmax router: allow iTunes and iPad/iPhone to see my Airplay B&W zeppelin Air when connected wireless but will not allow iTunes or my iPad/iPhone to see my Airplay Marantz NR1603 when connected via cat 5 cable. (I know the connection is fine on the NR1603, as it streams from internet radio with no problem at all)It seems to be just airplay that is not operational through the router.
View 2 Replies View RelatedBelkin Routers :: F7D4401 Change Wireless Channel For Windows 7
Jun 13, 2013how to change the wireless channel for windows 7 on the router belkin play max n600 hd model F7D4401 Dual-Band
View 1 Replies View RelatedBelkin Routers :: Put More Than One N300 Dual-band Wifi Range Extender On Home Network?
Jan 17, 2013Can I put more than one N300 Dual-Band Wi-Fi Range Extender on my home network?
View 4 Replies View RelatedBelkin Routers :: Change NAT Type From Moderate To Open For Xbox 360 N450 Dual Band?
Dec 31, 2012How to change my NAT type from moderate to open for xbox 360. Belkin n450 dual band
View 1 Replies View RelatedBelkin Routers :: Dual-Band Wireless Range Extender F9K1106 With AirPort Extreme?
Jan 12, 2013Does the Dual-Band Wireless Range Extender #F9K1106 work with the Apple AirPort Extreme Base Station?
View 1 Replies View RelatedBelkin Play N600 Exposing USB Hard Drive Attached To Router Within Sub-network
Aug 30, 2012I recently purchased the Belkin PLAY N600 router to create a private network for my home theatre setup.I have a primary home network 192.168.0.x (NetGear) which I use for all my computing needs. I extended a network cable to my Home theatre area and plugged in the N600 router. After this, I attached a USB external hard drive to the router and it works great. I can see it from the 192.168.2.x home theatre network (Belkin).I would like to expose the USB hard drive hooked to the Belkin Router to my primary network so that I can copy over my music and pictures without having to physically move the hard driveonto a PC connected to the primary domain.The Belkin router has a DMZ function which exposes an IP on its internal (192.168.2.x)network to the external (192.168.0.103) network.Is it feasible to expose the USB drive to my primary home network?
View 1 Replies View RelatedSMCD3G Cable Modem / Belkin Play N600 Router - Small Office Network?
Apr 21, 2011I'm trying to network a small office and have the following devices:
SMCD3G Cable Modem
Belkin Play N600 Router
Digi Mil-H1130 8 Port Ethernet SOHO Hub
Hubbel Cat5 Patch Panel (goes up to 12)
We're replacing our DSL line with a Cable line. Our DSL was a one piece wireless router/modem. When it was installed, it was inside our office, next to the server, and plugged into Wall Jack 1 for all the other computers to connect to. Our server plugged into this modem/router. We didn't have the Belkin Router at the time. The Patch Panel wires went into the Hub behind our office and everything was fine.
The cable modem is now next to the Hub and Patch Panel. I bought the router since we didn't have the wireless feature that the DSL had and everyone I spoke to said I need a router to set up the office. I ran one of the LAN lines from the modem into the Router where it says Modem (WAN). From the Router, I ran the line 1 (LAN) into the Hub. (Does the number matter if nothing is plugged into it in our office?) No computer is able to connect to the internet except my laptop which connects wireless. It works fine.
Another problem. We have a server computer that's Unix based. In order for anyone to connect to the server to access the office software used, the IP address of the router must be 192.9.2.1 or the computer your using won't connect via Multiview 2000 Terminal Emulator. I can't connect to the server because the IP address of the router is still 192.168.2.1. I don't know where I have to go in the router settings to change it. I've tried a few spots and it tells me the IP address is invalid. The settings I had with the DSL modem/router were:
Modem IP address - 192.9.2.1
Subnet Mask - 255.255.255.0
DHCP Start Address - 192.9.2.100
DHCP End Address - 192.9.2.150
It's not like I need to run wires. Everything is set. If something is plugged into a wrong spot, I can switch it.
Additional info:
There are 4 computers in the office and 8 numbered wall jacks.
Server computer - Wall jack 8 (IP address of this machine - 192.9.2.25)
XP Machine 1 - Wall jack 4 (can't connect to server! No internet.)
XP Machine 2 - Wall jack 1 (Is able to connect to the server! No internet.)
Win CE Machine - Wall jack 9 -
I assume. I have a wire that goes through the wall on this machine and it isn't marked. (Rarely used so not sure about server connection)
Wireless Windows7 laptop - connects to the internet fine since it bypasses all these wires. Can't connect to server.
Under the DHCP client list, only 2 computers are listed. The one that has internet is my computer. The other computer listed is wall jack 4 and that has internet now.
my computer - 192.9.2.2
wall jack 4 - 192.9.2.3
The router IP is 192.168.2.1 and the Cable Modem is 10.1.10.11. If I type either number into my web browser it will take me to the router setup page. I don't know where/how to check if it's only one device acting as DHCP. What I want to do is be able to get online with all the computers as well as have access to the software on the server through the office wall jacks. In order to do that I need the router IP address to be 192.9.2.1 and then I'd be able to connect to it.
Right now, one computer is able to connect to the server via hard wire but can't connect to the internet.Another computer is able to connect to the internet via hard wire but can't connect to the server.My laptop can connect wireless to the internet but not the server. In a perferct world, all the computers should be able to connect to both the internet and the server. Right now, it's one or the other with both hard wired machines and I don't know why. Is there a wire not in the hub right? Is a patch panel wire plugged into the wrong port of the hub? I don't know what's supposed to go where. tell me "wire X from the modem goes to Port Z of the router, and Wire Y from the the router goes to number V on the Hub, and that wire goes to number T on the patch panel for the Port number R in the office to work..." I'll try it.
Then I think all I need to do is change the router's IP address to 192.9.2.1 and everyone should be able to connect to the server through the Multiview 2000 Terminal Emulator.When I tried to change the IP address on the router it's telling me it's not valid. Under LAN settings it says 192.168.2.1 - when I try to change it to 192.9.2.1 it tells me LAN IP address is invalid. I clicked on More Info below that in the router page and a pop up gives me info. It says:
The "IP address" is the Internal IP address of the Router. To access the advanced setupinterface, type this IP address into the address bar of your browser. This address can be changed if needed. To Change the IP address, type in the new IP address and click "ApplyChanges". The IP address you choose should be a non-routable IP. Examples of a non-routable IP are:
192.168.y.x (where y is anything between 0 and 255, and x is anything between 1 and 254.)
10.y.y.x (where y is anything between 0 and 255, and x is anything between 1 and 254.)
172.z.y.x (where z is anything from 16 to 31, and y is anything between 0 and 255, and x is anything between 1 and 254.)
Belkin Routers :: Cannot Extend Signal With N300 Dual Ban Wifi Range Extender
Feb 10, 2013I am having problem using the N300 dual-Ban Wi-Fi Range extender with my att 2wire 3800HGV-B router. Cannot use the extender to access the internet. The Att router works without it. Just want to use the extender to extend my att router signal but cannot.
View 3 Replies View RelatedNetgear N600 Dual Band Gigabit Router - Channel Changed But It Still Seems To Lag?
Oct 20, 2011I have a Netgear N600 Dual Band Gigabit Router and my roomate and I both have the wireless xbox and when we connect to xbox live and find a game on call of duty mw2 we lagg our butt off nd we tried changing the channel on the router but it still seems to lag.
View 11 Replies View RelatedCan't Setup Netgear N600 Wireless Dual Band Gigabit Router
Dec 1, 2012I confused ,with which modem to purchase to set up my n600 wireless dual band gigabit router wndr3700, i'm on boardband with no modem
View 1 Replies View RelatedSlow Wired Connection On Netgear N600 WNDR3700v1 Dual Band Gigabit Router?
Aug 6, 2012I have a Netgear N600 WNDR3700v1 Dual Band Gigabit router and am having a problem with the wired connection with my PC. Everything wireless in the house works fine. In fact, I also have a Direct TV box hooked up for on demand and a sling box hooked up (both wired) and they work find. It's just my PC that is having issues. If I bypass the router and hook straight into the modem, it runs fine also so I have something going on between the router and this PC. I updated the NIC driver and this did not work. Before the update in the device manager, it said it was a NIVIDA nForce Network Controller (if I remember right) and now it says NIVIDA nForce 10/100 Mpbs Ethernet. It was suggested that I change my speed and duplex to match the router after I update but I am unsure what to change it to.
View 11 Replies View RelatedCabling / Cards :: WNDR 3400 N600 Dual Band Router - Experiencing Lag Spikes In Xbox
Mar 24, 2011My problem is with xbox live, i have the WNDR 3400 N600 Dual Band Router and i have been experiencing lag spikes since the day i have gotten it. I used to have a wireless adapter and i thought that was the problem so i recently went out and bought a 200 ft ethernet cable so now im hardlined to the router I have the xbox set to highest priority, i have it set with a static ip address for the dmz so i have no restrictions, i have all ports opened just in case, i have great internet speeds : 18.04 mbps download and 4.03 mbps upload and nothing seems to work.. i still have lag that sometimes disconnects me from xbox live and ruins the whole gaming experience.
View 3 Replies View RelatedTP-Link Dual-Band Wireless :: TL-WDR4300 - 2.4 GHz Signal
Mar 28, 2013Region : Venezuela
Model : TL-WDR4300
Hardware Version : Not Clear
Firmware Version :
ISP :
I have an issue with my TL-WDR4300 (regular, internet sharing use, no Open WRT or similar things). It was working well, until one day that my devices only receive the 2.4 GHz signal (no 5 GHz) and then I try to connect to 2.4 GHz and it asks for a password. I put my regular password and it doesn't work. Then I tried to bring it to factory default settings, I push the reset button for 8 seconds as the manual points and then same thing. What could I do?
TP-Link Dual-Band Wireless :: Very Poor Signal Strength On WDR4300
Mar 15, 2013Region : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 121225 Rel.37950n
ISP : Fullrate
No matter what I try, the signal strength never gets better that 30%, even when I have my laptop next to the router. I have tried various settings (found in these forums), but nothing seem to work. My old D-Link performed better, both close and over distances.
Belkin Dual Band Router - To Boost Up Wifi
Jan 28, 2012I recently purchased a Belkin Dual Band Router and connected to the internet at our side-house we have connected to the house. I'm getting a poor to fair signal out here. Just to mention, there is a lot of traffic passing at all times of the day and night. Busy highway. Is there a way I can boost my wifi signal without buying an actual wifi booster?
View 5 Replies View RelatedTP-Link Dual-Band Wireless :: Low Signal Range From WDR4300 Router On Both Bands And Especially On 5Ghz
Mar 24, 2013Region : Germany
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : Build 121225 Rel.37950n
I have low signal range from this WDR4300 router on both bands and especially on 5Ghz i lose my connectivity on just few meters away from the router and on other rooms in my 80m2 apartment, i also own another tp link 740n with only one antenna and the range is better with it almost covers all my apartment. Router has been reset after being updated to latest firmware and tried different configurations but im not satisfied with the signal range. Is there something i can do.
Belkin Routers :: Possibility For F7D4402nt Play 600 On Windows 8?
May 15, 2013F7D4402nt play 600. i updated to windows 8 and the supplied software will not work. The software was very easy for a setup. Now i must do the things the hard way. a completely manual setup. it is a bit of a chore.
View 1 Replies View RelatedBelkin Routers :: Play F7D4402Uk Connection Slow?
Nov 21, 2012My Router has been gone from running at bout 7Mb download speed to 500Kb download speed. When the router is restarted using the menu software it will run quicker, but only for 20-30 second then back to a slow speed. It was off while we were on holiday in August and has not been any good since. Its a shame as it only 2 years old.
View 2 Replies View RelatedBelkin Routers :: F5D8236-4 V3 / Cannot Download From Google Play Store On Wi-Fi But OK On 4G
Feb 3, 2013I can't download an app from Google Play Store. I can download from my 4G network but not the wifi - Belkin F5D8236-4 V3. Google troubleshooting says the firewall is blocking the 'ports required for Google Play to download (TCP and UDP 5228) on that network.' However, with the firewall 'disabled,' the download is still not working.
View 4 Replies View Related