Cisco WAN :: How Many Sources Can Be Supported By Monitor Session In Cat4900 (4948)
Feb 23, 2012For the command "monitor session 1 source" in Cat4900 (e.g. 4948), how many source interfaces can be supported per monitor session?
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Monitor Session In 4948 Don't Show Input Traffic
Jan 9, 2012I have a switch 4948, with version 12.2.31.sga4 ( I dont found bug about monitor session) and we try to made port mirroring with a monitor session from a VLAN and port belong at this VLAN have traffic input and output, but in the destination port, I always see it output traffic..
Global command
Red-127#sh run | in moni
monitor session 1 source vlan 1127
[Code].....
Cisco Switching/Routing :: 4948 Supported Stackable?
May 23, 2012MAC Support: 16000
Backplane: 18Gbps
Forward: 28Gbps
VLAN's: 4000 (q-in-q support)
Jumbo Frame Supported
Supported 8000 static routing
!Supporting Stack!
Cisco 4948 supporting stackable? which product do you recommend to these criteria?
Cisco WAN :: Monitor Session On 2921
May 8, 2011i have a question regarding the monitor session command. I have following interfaces on my router:i want to monitor the traffic from the source interface Gi0/2 to the destination interface fa1/3,monitor session 1 source interface gigabitEthernet 0/2 brings this error message % Incomplete command.,monitor session 1 source interface gigabitEthernet 0/2?/ : <0-2>,i don't have any ports on the Gigabit Interfaces. Any ideas how to monitor traffic?
View 1 Replies View RelatedCisco WAN :: 7606 Monitor Session Not Working?
Mar 5, 2012I've setup and configured the following local monitor session on a 7606 but it doesnt seem to be outputing anything. Any guess as to why, or what I might be doing wrong? Gi1/1 is doing ~40Mb/s egress & 15Mb/s ingress. Both source and destination ports are routed ports.
monitor session 10 source interface Gi1/1
monitor session 10 destination interface Gi1/10 ingress
interface GigabitEthernet1/1
description WAN Link to ********************* ** CORE BACKBONE **
mtu 9000
ip address ************** 255.255.255.252
[code].....
Cisco VPN :: Two ASA (v8.4) - IKEv1 And IKEv2 Session In ASDM Monitor?
Oct 25, 2012I have a L2L tunnel setup between two ASA's (v8.4). I used the wizard to set these up and selected the defaults of both IKEv1 and IKEv2, thinking that it would select one or the other. The strange thing is that now I see a separate session between these ASA's, one for IKEv1 and one for IKEv2. Both are passing traffic. Is this expected behavior? Should I disable IKEv1 to force only v2 since both are v8.
View 5 Replies View RelatedCisco Switching/Routing :: Set Up A Monitor Session With 3750 Stack
Aug 20, 2012i have just set up a monitor session with a 3750 stack .Simple enough task you would think.But i only seem to be seeing broadcast packets !!Now there is definitely unicast traffic being used on the host i am monitoring.I have done the basic commands
-monitor session 1 dest int fas 5/0/24
-monitor session 1 src int fas 5/0/34
Cisco Switching/Routing :: Unable To Clear Monitor Session From 6500
Mar 6, 2013I tried to clear monitor session on 6500 and keep on getting the following error:
%Another session parameters or permit-list is being configured %Please wait for another configuration to complete.
how i can go about clearing the monitor session.
Cisco Switching/Routing :: Couldn't Clear Monitor Session From 6500
Nov 21, 2011I tried to clear monitor session on 6500 and keep on getting the following error:
%Another session parameters or permit-list is being configured %Please wait for another configuration to complete.
how i can go about clearing the monitor session.
Cisco Switching/Routing :: How Many VLANs Can Span In Monitor Session On Nexus 7K
Mar 3, 2013rsbd7k01-p-vdca(config)# monitor session 2
rsbd7k01-p-vdca(config-monitor)# source vlan ?
<1-3967>
rsbd7k01-p-vdca(config-monitor)# source vlan 1 - 3967
ERROR: vlan 33-3967: Number of source vlans exceeds maximum
rsbd7k01-p-vdca(config-monitor)#
Cisco Switching/Routing :: Port Mirroring 2651 To Create Monitor Session From Source
May 20, 2013I have cisco 2651. It contains two FastEthernet interfaces: Fa0/0, Fa0/1.Fa0/1 has an ip address. Fa0/0 hasn't an ip address.I need to create monitor session from source Fa0/1 to destination Fa0/0. Then i want to connect my notebook to Fa0/0 to analyze some traffic from port Fa0/1
View 2 Replies View RelatedCisco Switching/Routing :: Monitor Session Local SPAN Small Output With 7606
Aug 22, 2012I am having difficulties with getting SPAN traffic over my WS-X6704-10GE (CFC).
CISCO7606
ios 12.2(33)SRE6, SUP720-3BXL
Trying to use the span feature, put the commands listed below in and they entered successfully, but the port is not being mirrored.
interface TenGigabitEthernet1/1
description PUBLIC
dampening
mtu 9216
ip address x.x.x.x x.x.x.x
[Code]....
Cisco Switching/Routing :: 6513 Monitor Session Source Vlan And Lost Packets At Destination
Feb 20, 2012We have 2 6513 switches with SUP720/PFC3A and various POE modules and a 6748-GE-TX facing our servers. Additionally, we have a 4Gbps portchannel trunk interconnecting the switches. We have approximately 300 Nortel IP 1140e phones in use between the two switches.For the purpose of call recording, we've attempted to mirror the voice vlan using various approaches and have been met with limited success. We mirrored the VLAN using tx, rx, and both. When using both we appear to get duplicate packets at the destination interface.We seem to lose packets completely going in one direction or another for a given call. Packets are lost before they get to the destination interface?
View 2 Replies View RelatedCisco :: ASA 5580 - Top 10 Destinations / Sources Have No Data
Mar 1, 2012In the Firewall Dashboard of my ASA 5580, I get data on every pane, except for the Top 10 Sources and Top 10 Destinations. Why is that, and what do I need to do to get data there?
View 1 Replies View RelatedCan Merge Two Sources Of Bandwidth Into One Router
Jan 12, 2011can i merge two sources of bandwidth into one router ?
View 1 Replies View RelatedCisco VPN :: 7301 - Multiple L2L IPSec Sources On One Router
Feb 4, 2012I'm trying to make a redundantish office/datacentre connection on the cheap. At the datacentre, we've got a 7301 (12.2(24)T5) and at the office we've got a Mikrotik RB1200 (5.12).The office router has two ADSL connections to two different ISPs, the datacentre router a single GigE to a colo provider. I'm trying to build an IPSec encrypted IPIP tunnel over each ADSL service to a separate loopback interface on the datacentre router, so I can run OSPF over the top for route exchange. I need to use two different loopbacks on the datacentre router so the office router can have a static route for each out each ISP ADSL. But I'm running into issues making encryption work on two different source addresses.Using the 'crypto map xxx local-address Loopback12' command, I can specify the outbound interface for one of the tunnels just fine, traffic moves as expected - while the other tunnel fails to encrypt. But is there a way of having two peers use two different local addresses, or applying two crypto maps to a single physical interface?
View 1 Replies View RelatedD-Link DIR-825 :: How To Add U-Boot Sources To Provided Archive
Feb 24, 2011The bootloader used by the device is U-Boot, which is also licensed under the terms of the GPL. Sadly these parts are missing from the source code package provided by D-Link. Therefore I am asking you to add the U-Boot sources to the provided archive or post them here in the forum.
View 12 Replies View RelatedCisco Firewall :: Subinterface On ASA 5520 - Extend Network Sources
Apr 23, 2013I am having an issue where I can't get to external network sources via my sub interface which is attached to a 192.168.10.X VLAN I created to for Guest wireless traffic. The internal interface is a 10.5.X.X network. I can get out the external interface, but anything that we have A records for such as our mobile iron server that we can hit from the outside via https and an external IP can't be hit from the subinterface at all. Would this be a DNS rewrite issue or inspection problem?
View 3 Replies View RelatedCisco :: 3750G-48 Good Sources Of Information To Program And Configure This Switch
Dec 24, 2012I am a very basic user on the Cisco Switch programming. I was given a Cisco 3750G-48 to tinker with in my home office. I was wondering if someone could lead me to some good sources of information to program and configure this switch? I am wanting to create a GB network in the house with the computers that I have and the storage arrays.
View 8 Replies View RelatedCisco :: Change / Remove Gateway Within Of Routing Information Sources In OSPF Protocol
Jul 4, 2012I want to know could we change or remove the Gateway (highlight) within of Routing Information Sources in OSPF routing protocol? [code]
View 9 Replies View RelatedCisco AAA/Identity/Nac :: ACS5.3 - Configuring Multiple Identity Sources
Aug 28, 2012I have an ACS 5.3 cluster, that is configured to use AD. There are a few wireless devices, and monitoring tools that do not have AD accounts. I would like to configure ACS to first check AD for the user authentication, and if that fails to roll over to the local (Internal Users) identity source where I can define these user accounts.
It seems that when the authentication hits the initial Identity Policy rule, it never moves onto the next one if the first fails.
Attached are screen shots that show how i'm configured for the test, i have a local user defined and I'm trying to log into the firewalls.
- Identity Definition : Screen shot of the main ACS definition for the rule i'm testing that's not working
- Identity Rule 1 : The configuration of rule 1 that if it fails i need it to move onto rule 2.
- Log Output : Screen shot for one of the failed attempts from the ACS View Log server.
Reason I need to configure it this way is:
- Wireless users authenticate to wireless using AD user accounts. Some hand held scanners do not support that and will need to authenticate using the MAC address.
- Authentication to Network devices for managment uses AD accounts. We have some monitoring tools that do not have AD accounts, and will need to be able to log into Network devices to issue some commands (Examples: Cisco Prime LMS and NCS, Infoblox NetMRI).
Cisco :: 4948 - 122-46.SG On AAA Authorization
Jul 21, 2012I have faced a problem regarding AAA line:
aaa authorization exec default group tacacs+ local
if i add this line in my cisco 4948 switch running on 122-46.SG.. The next time i telnet to the switch i get an automatic restart of the switch and all configs are lost.
IOS used:
cat4500-ipbase-mz.122-46.SG.bin
WS-C4948-10GE
Cisco :: How To Enable IP SLA On 4948 Switch
May 20, 2009I am trying to enable IP SLA on a Cisco 4948 switch (running 'cat4500-ipbasek9-mz.122-46.SG.bin') to test CiscoWorks IPM using this swtich as a source device. But I can't run the command "ip sla monitor" on this switch. It just has "ip sla responder". Is it possible to configura IP SLA on this source switch? Or can I do it only on routers?
View 6 Replies View RelatedCisco WAN :: 4948 - Enable PBR On VRF Interface?
May 1, 2012i have a requirement to enable pbr in vrf interface of a 4948 switch. but as i browse the internet, it is quite impossible to do that. is there any alternative way / feature to get the same result as pbr does? which is to reroute the specific vrf traffic to another interface based on source and destination ip address?
View 1 Replies View RelatedCisco WAN :: Configure QoS On 4948 Switch?
Jul 31, 2011how to configure QoS on Cisco 4948. I have three VLans in my network. First is video traffic second is the voice traffic and third is the data traffic . I need to set the priority in QoS in the following way
i.e. Video traffic - 1st pref
Voice traffic - 2nd pref
Data traffic - 3rd pref
how to configure for this requirement.
Cisco :: 4948 - SSH Log Not Showing Username
Aug 10, 2011 i have several Cisco 4948 in my network infrastucture, the issue that i´m having with them is when i try to view the ssh log appears something like this.. Aug 11 15:43:13 GT: %SSH-5-SSH2_USERAUTH: User '' authentication for SSH2 Session from 192.168.2.5 (tty = 1) using crypto cipher 'aes256-cbc', hmac 'hmac-sha1' Succeeded
The ip address is correct but the username is in blank i checked on other equipments (2960 access switches and 7200 series router) and they show the username field correctly...
The IOS version im using is (cat4500-ENTSERVICESK9-M), Version 12.2(50)SG1, RELEASE SOFTWARE (fc2)
The ssh configuration is as follows..
ip ssh time-out 60
ip ssh source-interface Loopback1
ip ssh logging events
[Code]....
Cisco :: Where To Download Ciscoview For 4948 Switch
May 14, 2013I just picked up some second hand 4948 switches and wanted to install the embeded managment software. I can't find it anywhere in the downloads section?
is there a better FREE solution for managing these? I tried config profesional, but it only shows the routing config. There seems to be so many options.
Cisco :: Configure NTP Between 6509 And 4948 Switches?
Nov 14, 2011our 6509 is configured as NTP master. Our 4948 is configured as NTP client.on each of these switches we have configured a management VRF.The problem is that 4948 can not synchronize its clock with NTP master. Both switches are directly connected.show cdp neighbor on 4948 switch:
6K5 Fas 1 138 R S I WS-C6509- Gig 2/2/43
interface config on 6509:
interface GigabitEthernet2/2/43
description *** Mgmt Switch Externe 1 ***
switchport
switchport access vlan 1900
switchport mode access
wrr-queue cos-map 1 1 1
[code]....
debugs on 6509 do not show any packets received or sent to 4948.
Cisco Switching/Routing :: Cannot Boot IOS On Switch 4948
Jul 14, 2012I cannot boot IOS, when i reload this switch it go to ROMMON. I try to uploand IOS but it still has problem. i think i may wrong some point during i did uploand.
This is problem
Switch#sh bootvar
BOOT variable = cat4500-entservicesk9-mz.150-2.SG3.bin,1;bootflash:cat4500-entservicesk9-mz.150-2.SG3.bin,1;bootflash:cat4500-entservicesk9-
[Code].....
Cisco WAN :: Switch 4948 Reboot After Applying Route-map?
Dec 11, 2011I'm trying to apply the following policy route in my switch 4948, but it suddenly crash. Is anything wrong in my commands? The switch is rebooting with an error:
System returned to ROM by abort at PC 0x0
My commands are:
access-lists 7 permit 10.140.22.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.220.24.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.216.36.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.216.38.0 0.0.0.255
[Code]......
Cisco Switching/Routing :: Getting Error In 4948 Switch
Mar 13, 2013My cisco 4948 switch is generating the below error,how do i troubleshoot this error.
*Mar 13 00:09:33.451: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 14 times)Packet received with invalid source MAC addre ss (00:00:00:00:00:00) on port Gi1/37 in vlan 1Gi1/37- to this port another 2950 switch is connected by trunk link.and to this switch end host is connected i.e.thin client
Cisco :: Enabling Net Flow In 2960 And 4948 Switches
Aug 26, 2012I am unable to input the command "ip flow-cache timeout active 1" to my cisco 2960 and 4948 switches. But i am able to do so in my cisco 6500 series switch. Hence how do i enable netflow on both 2960 and 4948 devices?My 2960 and 4948 are L3 switches. What commands or additional hardware module are required.
View 4 Replies View RelatedCisco WAN :: 4948 / NTP Master - How To Make Clock Set Become Permanent
Oct 29, 2012I understand that most of the cisco switches does not have a battery-supported system clock. The better solution is to setup the NTP server and let the rest of the switches to synchnorise the clock with it. How about cisco switch 4948? Does it have a battery-supported system clock?If the cisco switch 4948 is the NTP master, how I am going to make sure that the clock will not be reset after reload?
View 3 Replies View Related