how to configure QoS on Cisco 4948. I have three VLans in my network. First is video traffic second is the voice traffic and third is the data traffic . I need to set the priority in QoS in the following way
i.e. Video traffic - 1st pref
Voice traffic - 2nd pref
Data traffic - 3rd pref
how to configure for this requirement.
our 6509 is configured as NTP master. Our 4948 is configured as NTP client.on each of these switches we have configured a management VRF.The problem is that 4948 can not synchronize its clock with NTP master. Both switches are directly connected.show cdp neighbor on 4948 switch:
6K5 Fas 1 138 R S I WS-C6509- Gig 2/2/43
interface config on 6509:
interface GigabitEthernet2/2/43
description *** Mgmt Switch Externe 1 ***
switchport
switchport access vlan 1900
switchport mode access
wrr-queue cos-map 1 1 1
[code]....
debugs on 6509 do not show any packets received or sent to 4948.
I am trying to enable IP SLA on a Cisco 4948 switch (running 'cat4500-ipbasek9-mz.122-46.SG.bin') to test CiscoWorks IPM using this swtich as a source device. But I can't run the command "ip sla monitor" on this switch. It just has "ip sla responder". Is it possible to configura IP SLA on this source switch? Or can I do it only on routers?
View 6 Replies View RelatedI just picked up some second hand 4948 switches and wanted to install the embeded managment software. I can't find it anywhere in the downloads section?
is there a better FREE solution for managing these? I tried config profesional, but it only shows the routing config. There seems to be so many options.
I cannot boot IOS, when i reload this switch it go to ROMMON. I try to uploand IOS but it still has problem. i think i may wrong some point during i did uploand.
This is problem
Switch#sh bootvar
BOOT variable = cat4500-entservicesk9-mz.150-2.SG3.bin,1;bootflash:cat4500-entservicesk9-mz.150-2.SG3.bin,1;bootflash:cat4500-entservicesk9-
[Code].....
I'm trying to apply the following policy route in my switch 4948, but it suddenly crash. Is anything wrong in my commands? The switch is rebooting with an error:
System returned to ROM by abort at PC 0x0
My commands are:
access-lists 7 permit 10.140.22.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.220.24.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.216.36.0 0.0.0.255
access-list 177 permit ip 10.140.22.0 0.0.0.255 100.216.38.0 0.0.0.255
[Code]......
My cisco 4948 switch is generating the below error,how do i troubleshoot this error.
*Mar 13 00:09:33.451: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 14 times)Packet received with invalid source MAC addre ss (00:00:00:00:00:00) on port Gi1/37 in vlan 1Gi1/37- to this port another 2950 switch is connected by trunk link.and to this switch end host is connected i.e.thin client
I have a named aggregate policer configured on a 4948 switch running IOS 12.2(53)SG2 but can't seem to be able to monitor it using SNMP as I can't locate the OIDs (using OIDView) - I'm okay with CB and PB QoS.
View 1 Replies View RelatedIn my setup , i have one core switch 4506, 3750 access switches and 4948 server switch.i have created the mngmt VLAN in every switch.the problem is i can ping the every device mngmt ip from any internal network,but my server switch mngmt ip i am not able to ping.trunk link is configure between the core and server,access switches.What is the problem with 4948 switch?
View 7 Replies View RelatedI have got a new 48port Cisco catalyst 4948 switch, which I configured as a VTP client and connected to Cisco 3750 which is a VTP Server (this switch is on production network). I connected port g1/0/48 from 3750 to port g1/48 on 4948 through a straight cable and made both ports as trunk port (I also tried through cross cable). The problem is these two switches are not detecting. For testing I connected a PC directly to one of the port on 4948 (making that a switch port) still the LED on switch didn’t glow up. Is there any special command needs to be run on 4948 switches to activate its physical ports?
View 7 Replies View RelatedI need to connect a 6500 switch with a 4948 switch using 10G optics. On 6500, line card used is WS-X6704-10GE and I am aware that WS-X6704-10GE is a xenpak and 4948 ports are X2. What is the way to make the connection between xenpak and X2 work?
View 3 Replies View RelatedI performed an upgraded on a 4948 switch and for some reason the switch kept booting with the old IOS. I was not sure if I needed to change the boot sequence but I performed this upgrade on some of our other 4948's and no issues.I eventually deleted the older IOS version and left the latest version on and reloaded switch and now switch only boots in rommon.I managed to configure the ip info and tftp server ip etc and using the following command as suggested in the rommon help, but it keeps coming back saying 'file not found', when I have checked the file does exist in the tftp server and in the tftpboot folder.
See error message below:
[URL]
Tftp Session details are ....
Filename : /tftpboot/cat4500-ipbase-mz.122-54.SG1
IP Address : 10.250.100.39
Loading from TftpServer: 10.250.150.40
Tftp session failed: File not found
I have a problem, i would like todo MACSEC betwwen two switches cisco catalyst 3560-x but I know that for this operation i needed ACS server 5.1 is it possible to encryp dataflow without ACS server and if you have the configuration
View 7 Replies View Relatedi have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedI connect switch with IPcop my internet are slow but I connect direct Ipcop with 1 PC internet is process fast normal
View 1 Replies View Relatedi want to configure my switch as a gateway
View 2 Replies View RelatedHow to config SVI on Cisco 6509 switches??
View 1 Replies View RelatedI would like to configure a switch to act like a Hub. I know about the mirroring port configuration, but unfortunately is not enough for me. Is it possible to do that with the switch that I have (i.e. SG 200-08) ? If not do you know a switch on which I can configure it like a hub (that mean no flow control between physical ports).
View 1 Replies View RelatedI only have access to 1 pc and 1 router/switch.I know how to make the pc a tftp server with a tftp server program, which i can then upload my router config to.I now do not have access to that tftp program anymore and am trying to find another way to save the router config(not to nvram on the actual router but to my local pc).I have heard of peopel doing it with putty saving the log onto a file but how would you load that log??
View 1 Replies View RelatedI'm trying to configure a 2940 switch to trunk. I just can't get it to work.On the interface I have added: switchport mode trunk The default is encap for this switch is dot1q, so there is no need, or ability to add/change the encap mode. Also all vlans are being allowed by default. I still can't get any port to trunk. Need to get G0/1 to trunk, have also tried to trunk f0/6 to the switch in my office. Also can't find the command to change the management VLAN. I do not use vlan 1 for management. Can I change the Mang VLAN on this switch?
View 7 Replies View RelatedI want write comment for command when i config switch .i want when use show running display comment .
View 1 Replies View RelatedRight now I have it connected like this: Internet-> SURFboard SB6120 Modem -> DGL-4100 Router (modem in the WAN port, 3 internet connections plus the switch in the LAN ports) -> DGS-1008G Switch (2 other internet connections connected to this, as well as an Xbox 360).The problem is that everything connecting to the router works, and nothing works on the switch even though the power light is on (however, the port on the router that is receiving the switch is not lit up). I'm guessing this is because the router only assigns as many IP addresses as it has ports or something.
View 10 Replies View RelatedHow is it possible to configure 2 VLANs to communicate with each other on the same switch? I have managed to create 2 VLANS and they both work (and can access the internet), but they can't communicate with each other.VLAN1 has an IP range starting 10.4.160 and VLAN2 has an IP range starting 10.6.192.Is it VLAN routing that I'm looking for? My switch is Netgear GSM7328FS.
View 1 Replies View RelatedIs there a way to configure the switch remotely if it looses it's management IP.
View 14 Replies View RelatedI have routing enabled, can build a static route, and go back and see it (sh ip route), but I don't know how to get the route right. I have one host (Host A) on Vlan 20 w/192.168.20.2/24 dg 192.168.20.11 (the vlan ip) and (Host B) on Vlan 30 w/192.168.30.2/24 dg 192.168.30.11 (the vlan ip). I can't ping them from any host man. I can ping the Vlans but not the host.
View 19 Replies View Relatedhow do i configure cisco switch Edge
View 1 Replies View Relatedwe are using 2960 cisco switch asn we are trying to configure port security.we are able to configure MAC base port security, but unbale to configure IP base port security.can any one guide us can do IP base port security like MAC port security. if not which switch will support IP and Mac base port security.
View 6 Replies View RelatedI got one SF 300-48 layer 3 switch I tried to configure to use it in the office network.Unfortunately I'm unable to configure the VLAN settings.I need port one for input(VLAN2),port 7-15 for another vlan(vlan3) also need to connect with the vlan 4.port 15 is another vlan(vlan4) this is for wireless.Other ports are static.It doesn't get any connections with other vlans.I wish to know how to configure vlans in GUI mode.I tried , But I can't get the Vlan setting correctly.Also,I need to know how to communicate both vlans in GUI mode.
View 8 Replies View Relatedconfigure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies View RelatedI have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies View RelatedI am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies View Relatedconfigure QoS on 3560 switch i have taken the template from cisco configuration guide since we have different QoS configuration on each model.
below is the configuration :
configure terminal
mls qos
end
mls qos map cos-dscp 0 8 16 26 32 46 48 56
no mls qos srr-queue input cos-map mls qos srr-queue input cos-map queue 1 threshold 2 1 mls qos srr-queue input cos-map queue 1 threshold 3 0
[code]....
Currently all the cisco phones are connected to this switch and configuration with only one vlan that is voice vlan .
1) what is the outcome of this configuration , i mean, what will be the expected output ? end of the day we need to prioritize the voice traffic but why other commands including threshold and buffers are mentioned with respectives queues , if I need to explain that what am i expecting out of this configuration ?
2) this is LAN QoS which i understood but again , do i need to configure policy-map along with class-map which is MQC on this switch ?
3) i have edge router where i have MQC already configured but confusion with this switch which is working as a Access switch .
4) I referred the cisco QoS document for the respetive model whereas we have policy-map configured on the same switch with class-map .
My understanding is if we have configured the LAN QoS , and mapped the CoS value with DSCP , we need not to have MQC.
How to, for the most part, setup 802.1x via wireless. I'm using two 5508 WLCs, and Cisco ACS. I will setup the user account/password information via Cisco ACS and User Identity and Hosts. I know from the WLC 5508 web admin tool that I can choose 802.1x in the security parameters. I only have a few question. We have two wireless networks, one is wide open and provides internet access, the other will provide internal access for select users. I am setting up 802.1x on the internal wireless lan. Do I need to configure any 802.1 configuration commands on the switch in order for this to work, if so where would be the locations to do this at? Also, if there is a MAC isolation configuration option I can configure to not allow other hosts on this specific wireless network to communicate with each other?
View 3 Replies View Related