I am having difficulties with getting SPAN traffic over my WS-X6704-10GE (CFC).
CISCO7606
ios 12.2(33)SRE6, SUP720-3BXL
Trying to use the span feature, put the commands listed below in and they entered successfully, but the port is not being mirrored.
interface TenGigabitEthernet1/1
description PUBLIC
dampening
mtu 9216
ip address x.x.x.x x.x.x.x
[Code]....
rsbd7k01-p-vdca(config)# monitor session 2
rsbd7k01-p-vdca(config-monitor)# source vlan ?
<1-3967>
rsbd7k01-p-vdca(config-monitor)# source vlan 1 - 3967
ERROR: vlan 33-3967: Number of source vlans exceeds maximum
rsbd7k01-p-vdca(config-monitor)#
I've setup and configured the following local monitor session on a 7606 but it doesnt seem to be outputing anything. Any guess as to why, or what I might be doing wrong? Gi1/1 is doing ~40Mb/s egress & 15Mb/s ingress. Both source and destination ports are routed ports.
monitor session 10 source interface Gi1/1
monitor session 10 destination interface Gi1/10 ingress
interface GigabitEthernet1/1
description WAN Link to ********************* ** CORE BACKBONE **
mtu 9000
ip address ************** 255.255.255.252
[code].....
I have a need to capture some traffic but my core 6513's are already using the limit of 2 span sessions. I can't edit any of the sessions either because I want to source traffic from vlans and you can only do one or the other. Is using a VACL with 'switchport capture' on the destination interface an option ? E.g. I want to source traffic from vlan 10,20,30,40 and send the all to interface Gi10/10 ? Is there any caveats ? I dont need to be too granular with the ACL's but just capture all traffic in those vlans.
View 2 Replies View RelatedI'm setting up a montitor session on a NEXUS 7K as below.we are receiving in 150M of data and 0 data going out port 9/25.but port 4/24 shows 300M to the span port?
View 1 Replies View RelatedOn a Catalyst 6500, we configured a SPAN session with VLAN 300 as a source. We configured the session bi-directional ("both" keyword). We connect a sniffer on the SPAN destination port.
Strangely enough, we only see the traffic from the VRF to the firewall, but not the reverse traffic ! What can be the problem ?
If I monitor a trunkport on the rootbridge in both directions I get Duplicate Multicast Packets on the perticular VLAN. The first guess is, that this is worked as designed and not a IOS Bug (Platform CAT6500 SUP720 IOS 12.2(33)SXI9 ) Until know I only found an old Cisco press link from 2002 with this subject.
View 2 Replies View Relatedi have just set up a monitor session with a 3750 stack .Simple enough task you would think.But i only seem to be seeing broadcast packets !!Now there is definitely unicast traffic being used on the host i am monitoring.I have done the basic commands
-monitor session 1 dest int fas 5/0/24
-monitor session 1 src int fas 5/0/34
I tried to clear monitor session on 6500 and keep on getting the following error:
%Another session parameters or permit-list is being configured %Please wait for another configuration to complete.
how i can go about clearing the monitor session.
I tried to clear monitor session on 6500 and keep on getting the following error:
%Another session parameters or permit-list is being configured %Please wait for another configuration to complete.
how i can go about clearing the monitor session.
I have a switch 4948, with version 12.2.31.sga4 ( I dont found bug about monitor session) and we try to made port mirroring with a monitor session from a VLAN and port belong at this VLAN have traffic input and output, but in the destination port, I always see it output traffic..
Global command
Red-127#sh run | in moni
monitor session 1 source vlan 1127
[Code].....
I am having some problems creating a SPAN port on my Cisco 871 (running IOS 12.4-11T). My 871 is connected to a DSL modem, and uses "IP Negotiated" to get its dynamic ip address.I want to monitor the WAN port (FastEthernet4) using SPAN, but when I type "monitor session 1 source interface FastEthernet4" into the cli, it is rejected. I can successfully use any of the other FastEthernet ports, as well as Vlan1 as a source for the SPAN session. I have tried to use Dialer0 instead of FastEthernet4, but it still doesnt work.
View 5 Replies View RelatedI have cisco 2651. It contains two FastEthernet interfaces: Fa0/0, Fa0/1.Fa0/1 has an ip address. Fa0/0 hasn't an ip address.I need to create monitor session from source Fa0/1 to destination Fa0/0. Then i want to connect my notebook to Fa0/0 to analyze some traffic from port Fa0/1
View 2 Replies View RelatedWe have 2 6513 switches with SUP720/PFC3A and various POE modules and a 6748-GE-TX facing our servers. Additionally, we have a 4Gbps portchannel trunk interconnecting the switches. We have approximately 300 Nortel IP 1140e phones in use between the two switches.For the purpose of call recording, we've attempted to mirror the voice vlan using various approaches and have been met with limited success. We mirrored the VLAN using tx, rx, and both. When using both we appear to get duplicate packets at the destination interface.We seem to lose packets completely going in one direction or another for a given call. Packets are lost before they get to the destination interface?
View 2 Replies View RelatedI have configured SPAN session on 2960 switch, source port being a VLAN and destination being one of the fastethernet ports. All I see in the capture is control traffic (HSRP, RIP, Syslog, DNS..etc). However I dont see any real data traffic being captured. Below is how I have SPAN configured..
monitor session 1 source vlan <vlan_id> both
monitor session 1 destination interface fa0/42
i'm trying to setup a local DNS server to manage small office local-only domain names for our servers. i have the DNS working properly (resolving local machines and using the ISP dns if it can't). so i put the DNS server ip into the "Static DNS 1" field of the router settings. the other 2 static dns fields are empty.the problem is that the router is still using the ISP dns server as the primary and my local dns server as the secondary. i verify this in two places. first, if i go to the "status" tab, DNS 1 shows the ISP server while DNS 2 shows my local DNS server. secondly, if i connect to the wireless device with a linux-based machine, the /etc/resolv.conf file shows the nameserver ips in the same incorrect order.
View 1 Replies View RelatedI'm looking for temperature monitor (HDD, CPU) that can be run with parameters, and have cmd result output.I need some software to monitor temperature in Labtech software.
View 12 Replies View Relatedi have a question regarding the monitor session command. I have following interfaces on my router:i want to monitor the traffic from the source interface Gi0/2 to the destination interface fa1/3,monitor session 1 source interface gigabitEthernet 0/2 brings this error message % Incomplete command.,monitor session 1 source interface gigabitEthernet 0/2?/ : <0-2>,i don't have any ports on the Gigabit Interfaces. Any ideas how to monitor traffic?
View 1 Replies View RelatedI plug both the monitors to another VCD it works fine and if I've tested the VGA cables on both monitors and that is good as well. I was assuming it might be a monitor format issue so I tried to access the Monitor format option from the KBD5000 but it does not give me an option to change the format, I just have three buttons when I click on the Monitor Icon
View 1 Replies View RelatedI have a L2L tunnel setup between two ASA's (v8.4). I used the wizard to set these up and selected the defaults of both IKEv1 and IKEv2, thinking that it would select one or the other. The strange thing is that now I see a separate session between these ASA's, one for IKEv1 and one for IKEv2. Both are passing traffic. Is this expected behavior? Should I disable IKEv1 to force only v2 since both are v8.
View 5 Replies View RelatedWhat would cause debug output to not show on a remote session via telnet connection where you've enabled terminal monitor?
The reason I ask is I was working with a client and we were debugging WCCP. I ran the debug ip wccp packets and events commands, then entered terminal monitor. After this, we saw nothing. We should have at least seen particular WCCP-related packets because we saw the necessary cluster view was established which can't be done without the exchange of these packets.
Can having syslog (logging) configured cause the issue? Did I use the command incorrectly?
For the command "monitor session 1 source" in Cat4900 (e.g. 4948), how many source interfaces can be supported per monitor session?
View 1 Replies View RelatedI have two Cisco 7606 routers using BGP to connect our customers to the internet. Recently we added a new 1G circuit in addition to an existing 1G circuit and all traffic inbound is now on this new 1G circuit. We would like to shift some of the inbound traffic over to the other 7606. Our Tier provider has the same AS number for both paths. One path goes directly to New York and the other goes to Boston then New York.
View 1 Replies View RelatedI have made an etherchannel between 6509 and 7606 with two giga interfaces on eatch one to have more bandwidth (2Go), but the Etherchannel does not exceed 1 GB (Below is a capture for Etherchannel taken from Solarwinds).the both 6506 and 7606 use ws sup 720 3bxl
View 8 Replies View RelatedI have a Cisco 7606 running 12.2. I want to limit the interface that is used by one of our customers to 30M.
View 3 Replies View Relatedits a hardware problem or just not get power to module 1 for module WS-X6748-GE-TX? this is the capture from show module and sh log :
------------------ show module ------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX xxx
5 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE xxx
Mod MAC addresses Hw Fw Sw Status
[code].....
Our router suddenly reloaded. Below are the crashinfo obtained:
1st crashinfo:
7606_Router#more sup-bootflash:crashinfo_20120604-02260500:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
[code]....
We are running s72033-advipservicesk9_wan-mz.122-18.SXF9
I am hoping you can provide me with some opinions, feedback, thoughts on the following. We have some Cisco 6509 switches in our environment currently hitting around 60% usage on the Router overall statistics.
Now we are looking at implementing an intrusion detection system but by being as least invasive as possible to the network. Our thoughts are to utilize a SPAN port on the switches to send traffic to the NIDS device but we have concerns of the following. The limitations of SPAN sessions on 6509's . The overhead on the switch of turning a SPAN session on and leaving it on permanently.
I am trying to configure RSPAN for one of my client. They have Server-Client VTP architecture. Voice Recording Server is connected to C4507. Agents are connected to C2960 and C3750. I got 2 sessions configured and the connectivity is a as follows:
1. Voice Recording Server-----C4507-----C2960-----C2960-----Agent IP Phones (Session 1)
2. Voice Recording Server-----C4507-----C3750-----Agent IP Phones (Session 2)
Recording works with Session-2 but not with Session-1. I understand the problem could be due to multiple reasons: 1.1. C2960 is working in client VTP mode so i cannot add remote span command under the vlan configuration. 1.2. C2960 has LANLITE IOS image which i am not sure if it supports Remote Span.
following errors.
Nov 7 21:34:50: %EARL_NETFLOW-SP-STDBY-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [99%]
Nov 7 21:44:44: %EARL_NETFLOW-SP-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [91%]
I've already found this kinds of cases, in this community. So, It seems that Changing the current configuration to 'mls aging fast threshold ## time ## ' is most suitable in our situation.But, I don't know how to calculate the apt threshold value and time value.
[1] sh run | in mls
mls ip multicast flow-stat-timer 9
mls flow ip interface-full
no mls flow ipv6
no mls acl tcam share-global
mls cef error action freeze
[code]....
I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
I have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies View RelatedI have one Cisco 7606 and i need to install a WS-X6748-GE-TX with WS-F6700-DFC3CXL.When I install the WS-X6748-GE-TX the module is powered off with the following warning:
00:01:45: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported baseboard/earl combination. [code]
