Cisco Switching/Routing :: 7606 / Limit Interface That Is Used By One Of Customers To 30M
May 15, 2012I have a Cisco 7606 running 12.2. I want to limit the interface that is used by one of our customers to 30M.
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: WS-C6509 / VLAN Interface Limit
Jan 2, 2012I have Cisco WS-C6509 with IOS version 12.2(18)I have several vlan interface on this device.Today I create new vlan intervace
interface Vlan165
description test5
ip address 10.10.10.1 255.255.255.252
end
and vlan:
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
165 test5 active Gi7/14
But I can't ping this IP address and show ip route shows:
sh ip route 10.10.10.1
Routing entry for 10.10.10.0/24
Known via "static", distance 254, metric 0 (connected)
I have static route for this subnet /24?I can not see any error in logs, but looks like I reached vlan interface limit on this device or something like this.How can I check it?
Cisco Switching/Routing :: 6509-E - Rate Limit PPS On Interface?
Jun 8, 2013How (and is) it possible to rate limit pps on an interface (physical/logical), on a 6509-E?The porpuse is to protect from attacks which lead to very high pps, bypassing traffic rate-limits, and effecting the device's performance
View 2 Replies View RelatedCisco Switching/Routing :: Inbound Traffic On 7606?
Jan 17, 2013I have two Cisco 7606 routers using BGP to connect our customers to the internet. Recently we added a new 1G circuit in addition to an existing 1G circuit and all traffic inbound is now on this new 1G circuit. We would like to shift some of the inbound traffic over to the other 7606. Our Tier provider has the same AS number for both paths. One path goes directly to New York and the other goes to Boston then New York.
View 1 Replies View RelatedCisco WAN :: 7606 Interface Configuration?
Mar 5, 2012who to configure the interface of cisco 7606 router. As it is not getting up by doing normal configuration like "no shut"? iterface and line protocol both are down.
View 1 Replies View RelatedCisco WAN :: 7606 - Self IP Of Interface Not Pingable
May 1, 2012I have an Internet Gateway with dual homed to 2 ISP's terminated in 2 different routers in my end. My end routers are 7606 routers.
I have a WAN link from Router 1 to ISP1 and from Router 2 to ISP2.
Router 1:
-------------
int Gi1/1
description " Link to ISP1"
ip address x.x.x.142 255.255.255.252
x.x.x.141 is configured in ISP end router.
The problem I m facing is that I m not able to ping x.x.x.142 from this router. But x.x.x.141 is pingable.
Also when I check from any internet route server, I m able to ping both x.x.x.142 and x.x.x.141.
Cisco Switching/Routing :: Etherchannel Between 6509 And 7606 Not Exceeding
Jun 2, 2013I have made an etherchannel between 6509 and 7606 with two giga interfaces on eatch one to have more bandwidth (2Go), but the Etherchannel does not exceed 1 GB (Below is a capture for Etherchannel taken from Solarwinds).the both 6506 and 7606 use ws sup 720 3bxl
View 8 Replies View RelatedCisco Switching/Routing :: Getting Module WS-X6748-GE-TX PWRDown On 7606?
Jan 28, 2013its a hardware problem or just not get power to module 1 for module WS-X6748-GE-TX? this is the capture from show module and sh log :
------------------ show module ------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX xxx
5 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE xxx
Mod MAC addresses Hw Fw Sw Status
[code].....
Cisco Switching/Routing :: Software-forced Reload On 7606?
Jun 3, 2012Our router suddenly reloaded. Below are the crashinfo obtained:
1st crashinfo:
7606_Router#more sup-bootflash:crashinfo_20120604-02260500:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
[code]....
We are running s72033-advipservicesk9_wan-mz.122-18.SXF9
Cisco Switching/Routing :: 7606 / Netflow TCAM Threshold Exceeded
Nov 6, 2011 following errors.
Nov 7 21:34:50: %EARL_NETFLOW-SP-STDBY-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [99%]
Nov 7 21:44:44: %EARL_NETFLOW-SP-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [91%]
I've already found this kinds of cases, in this community. So, It seems that Changing the current configuration to 'mls aging fast threshold ## time ## ' is most suitable in our situation.But, I don't know how to calculate the apt threshold value and time value.
[1] sh run | in mls
mls ip multicast flow-stat-timer 9
mls flow ip interface-full
no mls flow ipv6
no mls acl tcam share-global
mls cef error action freeze
[code]....
Cisco Switching/Routing :: System Returned To ROM By Reset SP Error Of 7606-S
Jan 15, 2012I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
Cisco Switching/Routing :: 7606-S / RSP720 - Fails / None Of RSPs Booting
Feb 28, 2012I have a cisco 7606-S with dual RSP720-3CXL. Devices reloaded and now none of the RSPs are booting.When I have tried to take the console using only one RSP, card going to rommon mode after that it hangs. I guess its firmware is corrupted.
View 4 Replies View RelatedCisco Switching/Routing :: 7606 Need To Install WS-X6748-GE-TX With WS-F6700-DFC3CXL
Nov 13, 2012I have one Cisco 7606 and i need to install a WS-X6748-GE-TX with WS-F6700-DFC3CXL.When I install the WS-X6748-GE-TX the module is powered off with the following warning:
00:01:45: %C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 1, power not allowed: Unsupported baseboard/earl combination. [code]
Cisco Switching/Routing :: 7606 Sup720 With MSCF / Upgrade To 122-33.SRE6 Fail?
Mar 25, 2012I faced with problem while i was attemping to upgrade CISCO7606 (R7000) from 12.2(33)SRE1 to 12.2(33)SRE6.
rommon 2 > boot c7600s72033-advipservices-mz.122-33.SRE6.bin
Loading image, please wait ...
Invalid device specified
Booting from default device
Initializing ATA monitor library...
string is bootdisk:c7600s72033-advipservices-mz.122-33.SRE1.bin
[code].....
Cisco Switching/Routing :: Monitor Session Local SPAN Small Output With 7606
Aug 22, 2012I am having difficulties with getting SPAN traffic over my WS-X6704-10GE (CFC).
CISCO7606
ios 12.2(33)SRE6, SUP720-3BXL
Trying to use the span feature, put the commands listed below in and they entered successfully, but the port is not being mirrored.
interface TenGigabitEthernet1/1
description PUBLIC
dampening
mtu 9216
ip address x.x.x.x x.x.x.x
[Code]....
Cisco Switching/Routing :: 7606-S / SAMI Module WS-SVC-SAMI-BB-K9 Led Is Indicate Red
Jun 25, 2012 I have Cisco router 7606-S. On Sami module led is indicate red. i also test it to other slot,reload the chassis but the problem is same. The module status is unnkown.
(Indicates red one of the following conditions:
• The SAMI is released from reset by the supervisor engine and is booting.
• The boot code failed to run.)
pdsn1#sh mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 7 SAMI Module WS-SVC-SAMI-BB-K9 SAL15056HSV
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL14480S9Q
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE SAL1538QE8N
6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE SAL1538QHZB
[code]....
1.is this a hardware problem of sami module?
2. is this a boot problem of sami module? is this image problem of modules(supervisor or sami module)?
how i do diagnostics this module?
Cisco Switching/Routing :: ASA 5505 Cannot Ping From Inside Interface To Outside Interface
May 1, 2012I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
Cisco Switching/Routing :: To Limit Bandwidth Using The MAC On 2960
Jun 11, 2013Any example to limit the bandwidth using the MAC address on 2960 ? I want to limit the bandwidth (IN / OUT) of a server only for Internet flows.
View 2 Replies View RelatedCisco Switching/Routing :: VLans Limit On 2950?
Jun 12, 2012I have 10 2950 switches on my network that support only 64 vlans on each one. I actualy have requrement to cleate around 100 vlans acros them, can I switch off vtp and create required vlans manualy? I will have more or less following set up:
router
|
2950 - vlan 1,2,3,4,5,6,7,8,9,10
[Code].....
Cisco Switching/Routing :: 4500 - STM-4 (622) / How To Limit FTP Traffic
Mar 10, 2012I have the attached setup. now i would like to limit my ftp transfer to 10 mb from a specific vlan to ftp server on the STM-4 (622) link. what would be the best way to limit ftp traffic to 10 mb .
following is my switch deatils
Video_Main#sh verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)Technical Support:
[URL]
Cisco IOS-XE software, Copyright (c) 2005-2010 by cisco Systems, Inc.All rights reserved. Certain components of Cisco IOS-XE software arelicensed under the GNU General Public License ("GPL") Version 2.0. Thesoftware code licensed under GPL Version 2.0 is free software that comeswith ABSOLUTELY NO WARRANTY. You can redistribute and/or modify suchGPL code under the terms of GPL Version 2.0. For more details, see thedocumentation or "License Notice" file accompanying the IOS-XE software,or the applicable URL provided on the flyer accompanying the IOS-XEsoftware.
[code]....
Cisco Switching/Routing :: Rate Limit Configuration On 2950
Jun 10, 2012I configured rate limit on cisco 2960 switch sexuss fully, but i could not configure in cisco 2950 (verson 12.1 (22).To confiure the same on 2950
View 4 Replies View RelatedCisco Switching/Routing :: Rate Limit 3560 Outbound To 5mb?
Jun 9, 2013How to rate limit a 3560 inbound and outbound using different QoS methods. I've read about vlan class maps/policy maps, using the rate limit command on the physical interface, using the srr-queue bandwidth command(it's a gig switch so not sure that would work) and marking all packets and then applying QoS. I'm just learning QoS so trying to figure all of this out and find the best way to do things.
Also, I was told to do this because it's not advisable to have a connection to your ISP that is not 10mb or 100mb on a switch, since they are not divisible by 10 and it can cause issues?
Cisco Switching/Routing :: Bandwidth Limit On Catalyst 2960?
Feb 9, 2012I have ciscl catlyst 2960 8port switch, (flash:c2960-lanbasek9-mz.122-50.SE4/c2960-lanbasek9-mz.122-50.SE4.bin).
and in need to configure bandwidth limit for one of the port as a 1Mbps.
Cisco Switching/Routing :: 2921 / Limit Access By HW Address?
Sep 15, 2012I have a 2921, and I have 4 network segments. In segment 172.16.0.0./27 I wand to "pair" somehow connections. I mean IP 172.16.0.x has to have MAC aaaa.bbbb.cccc and so on, and not accept connections otherwise.How can I do that?
View 7 Replies View RelatedCisco Switching/Routing :: 6513 Span Session Limit?
Jul 12, 2012I have a need to capture some traffic but my core 6513's are already using the limit of 2 span sessions. I can't edit any of the sessions either because I want to source traffic from vlans and you can only do one or the other. Is using a VACL with 'switchport capture' on the destination interface an option ? E.g. I want to source traffic from vlan 10,20,30,40 and send the all to interface Gi10/10 ? Is there any caveats ? I dont need to be too granular with the ACL's but just capture all traffic in those vlans.
View 2 Replies View RelatedCisco Switching/Routing :: Rate Limit Traffic In 3560
Oct 20, 2011I am using Cisco 3560 as distrubution switch and want to limit port 445 traffic on 1 MB and applied rate limit statment on Gi0/1 port but switch unable to limit said traffic.rate-limit output access-group 120 1024000 128000 128000 conform-action transmit exceed-action drop.
View 25 Replies View RelatedCisco Switching/Routing :: Bandwidth Limit On 2950 Switch?
Mar 25, 2012I have cisco 2950 catalyst switch, verson IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(20)EA1a, RELEASE SOFTWARE (fc1)
So. for one of my port (FE 0/3) i need to put the bandwith limit 512 kbps, how to configure the above same.
Note:- I configured the below but no effect
1. interface FastEthernet0/3description * CONT TO B-CENTER *switchport access vlan 10switchport mode accessbandwidth 1024speed 10
2. and there is no srr bandwidth limit option for 2950, but the same is working for 2960.
Cisco Switching/Routing :: Rate Limit 2960 Port To 1 MB
Nov 5, 2009To rate limit the 2960 switch port to 1 MB.I have made the specified chnages , how ever still it is reaching more tha 1 MB
Hard coded the bandwidth of port to 10 MB and have applied the specified command srr-queue bandwidth limit 10.
Cisco Switching/Routing :: WS-C3560-24PS - Rate Limit And QoS
Mar 4, 2012I am having an issue with VoiP phones giving me an insufficient bandwidth message. I have three remote locations connected to our main building using 2 Mb point to point ethernet solutions through TWC. Each remote location has a Cisco WS-C3560-24PS running IOS C3560-IPBASE-M, version 12.2(25) and have the cable modems plugged into port 1 on them. The remote buildings are labeled 192.168.101.xxx, 192.168.102.xxx, and 192.168.103.xxx. There are 14-16 VoiP phones in each remote building. The main building being in the subnet of 192.168.100.xxx. I have the 3560s connecting to a single port on a 2801 in the main building, all using the subnet of 192.168.253.xxx The phone server sits in our network at 192.168.100.203. I have created the ACLs, class maps, and policy maps on all of the equipment.
For the remote buildings I have the following:
ACL
===========
Extended IP access list VOIP
permit tcp any host 192.168.100.203 dscp ef
permit tcp any host 192.168.100.203 eq 5566
[Code]....
I have put a hub in to capture traffic via Wireshark to see if DSCP flags are being appropriately marked and I do see that all VoiP packets are getting marked with as EF. However, I have been receiving phone calls from people in the remote buildings stating that their phones will cut out, flash Insufficient Bandwidth on the LCD displays and then the call will cut back in. I am wondering if the 2801 is not applying QoS with the rate-limits in mind since it is set to 100 Mb, or is it an issue with trying to take 3 remote locations and bring them down into 1 port on the 2801?
Cisco Switching/Routing :: 2921 - Queue-limit With Shaping
Mar 8, 2012I have a 2921 where I am shaping some traffic based on sub net on my lan. I have applied the shaping policy to the lan interface in the outgoing direction.
Topology is as follows:
ISP - ASA - ROUTER - LAN
Policy map:
Policy Map shape-lan
[code]....
I am seeing a lot of no-buffer drops on the policy and I am wondering what the best solution is to solve this:
Class-map: tc-class (match-any)
8730680 packets, 10803689863 bytes
5 minute offered rate 4453000 bps, drop rate 0 bps
[code]....
Should I just be increasing the queue-limit or should I be changing something else?
Cisco Switching/Routing :: 6509 - IP Multicast Rate Limit
Nov 26, 2012How is it i can implement the command 'ip multicast rate-limit out group-list <access-list>' but i get the error "ip multicast rate-limit" command is not supported on 6509?
Is it an IOS limitation or a limitation of the switch series and subsequently can't be used at all?
Cisco WAN :: 3700 Rate Limit In Interface
Feb 24, 2011I am not able to disable rate limit comand from Cisco 3700 series router. I have tried with no rate limit command in the interface .Command is taking but still the rate limit comman in the interface.
View 2 Replies View RelatedCisco Switching/Routing :: 6513 - Rate Limit And Traffic Shaping?
Mar 21, 2012I am looking for step-by-step configuration on how to enable rate-limit and traffic shaping on Cisco 6513 vlan interfaces. I am not able to find this particular document on CCO.
View 3 Replies View Related
