Cisco WAN :: 7606 - Self IP Of Interface Not Pingable
May 1, 2012
I have an Internet Gateway with dual homed to 2 ISP's terminated in 2 different routers in my end. My end routers are 7606 routers.
I have a WAN link from Router 1 to ISP1 and from Router 2 to ISP2.
Router 1:
-------------
int Gi1/1
description " Link to ISP1"
ip address x.x.x.142 255.255.255.252
x.x.x.141 is configured in ISP end router.
The problem I m facing is that I m not able to ping x.x.x.142 from this router. But x.x.x.141 is pingable.
Also when I check from any internet route server, I m able to ping both x.x.x.142 and x.x.x.141.
View 1 Replies
ADVERTISEMENT
Mar 5, 2012
who to configure the interface of cisco 7606 router. As it is not getting up by doing normal configuration like "no shut"? iterface and line protocol both are down.
View 1 Replies
View Related
May 15, 2012
I have a Cisco 7606 running 12.2. I want to limit the interface that is used by one of our customers to 30M.
View 3 Replies
View Related
Apr 20, 2013
We have a cisco 2811 router with 2 ADSL interfaces. One dialer interface is used for internet and another dialer interface is used for VPN.
The dialer interface that is used for internet purpose is "Dialer 1" and the VPN is "Dialer 2".
The route looks like this: ip route 0.0.0.0 0.0.0.0 dialer 1
Basically, I am able to the ping the external IP address associated with the Dialer 1 interface, however, I cannot ping the external IP address associated with Dialer 2.
View 5 Replies
View Related
Jul 17, 2012
I am having an issue where the GRE tunnels are up/up but are not pingable. The GRE tunnels are on a cisco 1811 and cisco 2811 routers The tunnel source and destination IP addresses are private addresses. These private addresses are pingable to each other and they are connected via IPSEC. The IPSEC tunnels are generated from the ASA to which the cisco routers connect. Probably the tunnels are up/up because keepalives are not configured. But I am still not able to see why I cnt ping the end points. The ACL for IPSEC in ASA includes the "permit gre host <Private IP 1> hist <Private IP 2>" commands.
View 2 Replies
View Related
Jan 26, 2013
A Customer has a 1262N-WGB connected via LWAPP to a 5508 Controller.(7.2.x.x)Behind the WGB they have a no-name switch and connected to that two D-Link cameras.I am not able to ping these cameras. When I connect my laptop to that switch it is no problem. I am getting an IP and the laptop is pingable.The cameras are also getting an IP, I see them for 5 to 10 seconds as clients on the WGB on the WLCI tried all that stuff with "passive client", arp entry on WLC and Layer 3 switch, but still no luck!Also the entry on the WGB "bridge 1 address MAC fortwarf Gig 0Solutions?Sent from Cisco Technical Support iPad App
View 6 Replies
View Related
Jul 3, 2012
I'm having an issue with the 5508 management port .. I can't seem to ping it from the switch connected to it .. ( the Show cdp command shows that the two can see each other .. but no ping is possible ! [code]
View 4 Replies
View Related
Oct 12, 2011
An 1841 is conencted to the internet by DSL, it works fine. I have added it to the 10.98.8.x subnet off a 3750 switch.When I connect other devices to the same switch port, I can ping/browse to them fine, but when I connect the 1841 I can only ping it from the 3750, not another subnet connected to the same router. [code]
View 2 Replies
View Related
Aug 27, 2012
I have a Cisco Wireless LAN Controller WCL2112 model. It's currently plugged into an HP Procurve switch on a trunk port. That HP switch is plugged into my Cisco stack on a trunk port. I can reach the WCL just fine through the LAN. But when I plug the WCL directly into the Cisco stack on a trunk port, I can't reach the WCL at all, unless I connect to it over wireless. The interface shows it's conneccted and up/up. But no communications are sent across the line. I did a wireshark and can see only ARP request from the WCL. The trunk port on the stack is set to:
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport mode trunk
The WCL has 3 VLAN's on it and the SSID of VLAN 1 is our office wireless. If that matters. .The Cisco Stack is 4 switches. cisco WS-C3750X-48P
View 3 Replies
View Related
Dec 6, 2011
I need to create a policy to provide only 4 Mbps bandwidth for mail out of 16 mbps pipe terminated on 7606 router (at Datacenter) having WS-SUP32-GE-3B.But I can't create policy with bandwidth percent,even exact value with priority command does not work. When I am going to enter service policy output command at interface it is showing as"priority command is not supported in output direction for this interface Configuration failed!" All I want to restrict bandwidth at backbone link for mail traffic. From all remote locations use to access mail server over the same link.
View 1 Replies
View Related
Apr 18, 2011
high CPU on newly installed 7606.
CPU utilization for five seconds: 61%/59%; one minute: 62%; five minutes: 63% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 578 5856 9392486 0 0.55% 0.50% 0.50% 0 IP SLAs XOS Even 231 90364 576908
[Code]......
View 1 Replies
View Related
Jan 18, 2013
I tried to reboot manually and I changed the slot but the same behavior:
%SYS-SP-3-LOGGER_FLUSHING: Systema pausing to ensure console debugging output
%OIR-SP-6-CONSOLE: Changin console ownership to route processor
*** System received a Software forced crash ***
signal= 0x17, code= 0x24, context= 0x430213e4
PC = 0x4038c124, Cause = 0x1020, Status Reg = 0x34008102
View 1 Replies
View Related
Sep 28, 2012
Our Router 7606 is in a problem with high CPU Utilization. We are using one EBGP and one IBGP session. We are also running OSPF with area 0 between two IBGP router to exchange few local networks. When bandwidth cross 100 MB than only CPU use become 100%. when bandwidth consumption is 80MB CPU use become 80% end so on.
Out put is when bandwidth consumption is 34MB
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
78 44 9625 4 0.39% 0.03% 0.00% 2 Virtual Exec
13 40 375 106 0.07% 0.00% 0.00% 0 ARP Input
30 116 1098 105 0.07% 0.01% 0.00% 0 IPC Seat Manager
[code]....
View 27 Replies
View Related
Sep 18, 2012
I have a fresh piece of 7606-S router, i am planning to install a new IOS ( 15.2.4S or 12.2.33-SRD8 ) SIP-200 / RSP720 moduls ... would ypu plese provides me a configuration guide for installing IOS for 7600 serise router.I have the image on TFTP server.
View 3 Replies
View Related
Mar 18, 2011
I was trying to install a SPA-IPSEC-2G on 7606-S chassis. I installed the SPI/SPA cards in slot 3, after that I checked with "sh module" and we could see the module "OK". After this we tried to configure a VPN tunnel but we received messages in the other router about "no ipsec package".
I was checking and I tried "sh crypto engine accelerator statistic" and we got the message: " There is no crypto device".
I don't know about installation commands in references and I don't know about restrictions or configuration modes.
View 3 Replies
View Related
Jul 19, 2011
I have a 7606 router with sup 720-3bxl. IOS has been crashed recently and i can use only Roman mode now. Ive tried to upload ios image using tftp server but the command tftpdnld id not available in this router. I don't know why. Then i tried to boot from flash disk but finally it also shows an error like
System received a Software forced crash signal= 0x17, code= 0x24, context= 0x42359674 PC = 0x402d248c, Cause = 0x1020, Status Reg = 0x34008002
How to make the router in running condition.
View 3 Replies
View Related
Apr 16, 2011
We have 7606 router without any ipsec module on it,so i check the ios and it has all commands in interface tunnel for configuring the dmvpn multipoint tunnel and also protection profile for ipsec! so i have this question: do we can run dmvpn between this router and our wan routers wich are 3845.
View 2 Replies
View Related
Mar 5, 2012
I've setup and configured the following local monitor session on a 7606 but it doesnt seem to be outputing anything. Any guess as to why, or what I might be doing wrong? Gi1/1 is doing ~40Mb/s egress & 15Mb/s ingress. Both source and destination ports are routed ports.
monitor session 10 source interface Gi1/1
monitor session 10 destination interface Gi1/10 ingress
interface GigabitEthernet1/1
description WAN Link to ********************* ** CORE BACKBONE **
mtu 9000
ip address ************** 255.255.255.252
[code].....
View 1 Replies
View Related
Nov 10, 2011
I need to put a FWSM and a line card WS-X6148A-GE-TX to a router 7606. The FWSM version is 3.2(13). The router is running IOS 12.1(18)SXD3. The Cisco document here says the required IOS for router 7606 is 12.2(18)SXF or higher. I have downloaded the IOS 12.2(33)SRD4 and loaded it to the flash card. When I turn the router on, it doesn't load the new IOS and goes to rommon. Which IOS I should use to make the router 7606 work and accept the FWSM.
View 2 Replies
View Related
Jun 5, 2012
We are planning to configure the ipv6 PBR on our 7606 routers. We have configured the route-maps successfully .but when we tried to apply those on interfaces we are facing an problem .
when we trying to give command # ipv6 policy route-map <route map name> . we are unable to find policy command option in the command list.
IOS Version : c7600rsp72043-advipservicesk9-mz.122-33.SRE3.bin.
View 1 Replies
View Related
Nov 5, 2012
We have an environment where we terminate our DSL customers over PPPoE on a 7606-S MPLS PE router with RSP720. The PPPoE sessions are terminated on a GIG V2 interface of a SIP-400. Currently the IOS running on the device is c7600rsp72043_rp-ADVIPSERVICESK9-M, Version 12.2(33)SRD. The following is the current configuration used.
bba-group pppoe 7virtual-template 7
interface GigabitEthernet2/1/3.142647 accessencapsulation dot1Q 14 second-dot1q 2647pppoe enable group 7
interface Virtual-Template7 ip vrf forwarding TESTip address 10.10.10.1 255.255.255.252
In the above scenario everything works well.
However we had to upgrade the router IOS to 15.2(4)S Advance IPServicesk9 to support 4-byte ASN. After the upgrading we observed certain commands used to terminate PPPoE on the sub-interfaces not available on 15.2(4)S , although PPPoE on Gig and Ethernet with QinQ support is listed under 15.2S feature set.
View 1 Replies
View Related
Jan 17, 2013
I have two Cisco 7606 routers using BGP to connect our customers to the internet. Recently we added a new 1G circuit in addition to an existing 1G circuit and all traffic inbound is now on this new 1G circuit. We would like to shift some of the inbound traffic over to the other 7606. Our Tier provider has the same AS number for both paths. One path goes directly to New York and the other goes to Boston then New York.
View 1 Replies
View Related
Sep 17, 2012
I used the below syntax to check the snmpwalk to an interface of a cisco 7606-s router from an LMS 4.0 version cli.
NMSROOT/Objects/jt/bin>snmpwalk -v 2c -c <snmp-string> <ip-addr> 1.3.6.1.2.1.31.1.1.1.6
Timeout no response from <ip_address>
This is the error im getting in cli prompt. But i could see that reports are generating.If i try with the loopback ip address, i get proper snmpwalk outputs.. I have increased the timeout and retry options..
View 3 Replies
View Related
Sep 15, 2012
I have a 7606 Router with single Route Switch Processor 720 at the chassis works as active RP ( Route Processor ). Can I add another RP to the chassis as standby in case of failure of the first RP ?
View 28 Replies
View Related
Sep 29, 2012
I have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?
-are there any steps should i do before the upgrade ?
-i am planning to take the router out of service during the operation, how much down time it will be ?
View 4 Replies
View Related
Jun 2, 2013
I have made an etherchannel between 6509 and 7606 with two giga interfaces on eatch one to have more bandwidth (2Go), but the Etherchannel does not exceed 1 GB (Below is a capture for Etherchannel taken from Solarwinds).the both 6506 and 7606 use ws sup 720 3bxl
View 8 Replies
View Related
Jan 28, 2013
its a hardware problem or just not get power to module 1 for module WS-X6748-GE-TX? this is the capture from show module and sh log :
------------------ show module ------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX xxx
5 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE xxx
Mod MAC addresses Hw Fw Sw Status
[code].....
View 4 Replies
View Related
Oct 19, 2011
Any know how to close these open ports on my Cisco 7606 router? Any know what these TCP ports are used for?
:
49 - Not sure what this one is other than what IANA reports about TCP port 49
4510
4509
2222
:
I'm sure I could add an ACL to block communications to my router based on this ports but would rather figure out how to close 'em so this already overloaded router doesn't have additional processing.
View 3 Replies
View Related
Sep 27, 2010
I have the following configurations in cisco CISCO7606 (R7000). Its meaningful to have the below configuration, wherein , we are allowing multiple vlans on the access port?
interface FastEthernet4/45
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 124-127,423,478,493,578,699,751,787,895,987,1981
switchport mode access
end
interface FastEthernet4/46switchportswitchport trunk allowed vlan 124-127,423,478,493,578,699,751,787,895,987,1981switchport mode accessend
View 3 Replies
View Related
Jun 3, 2012
Our router suddenly reloaded. Below are the crashinfo obtained:
1st crashinfo:
7606_Router#more sup-bootflash:crashinfo_20120604-02260500:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:05: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor
00:00:05: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
[code]....
We are running s72033-advipservicesk9_wan-mz.122-18.SXF9
View 14 Replies
View Related
Dec 27, 2011
Im having problem configuring policies for limiting traffic on subinterfaces on cisco Router 7606-S. I have configured:
[code]...
So for egressQOS , i want to configure with police, not shape (for the memory reason).
View 4 Replies
View Related
Nov 6, 2011
following errors.
Nov 7 21:34:50: %EARL_NETFLOW-SP-STDBY-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [99%]
Nov 7 21:44:44: %EARL_NETFLOW-SP-4-TCAM_THRLD: Netflow TCAM threshold exceeded, TCAM Utilization [91%]
I've already found this kinds of cases, in this community. So, It seems that Changing the current configuration to 'mls aging fast threshold ## time ## ' is most suitable in our situation.But, I don't know how to calculate the apt threshold value and time value.
[1] sh run | in mls
mls ip multicast flow-stat-timer 9
mls flow ip interface-full
no mls flow ipv6
no mls acl tcam share-global
mls cef error action freeze
[code]....
View 1 Replies
View Related
Jan 15, 2012
I have my router 7606-S rebooted by itself. According to output of show version command it's rebooted by software bug.
================ Snipped from crashinfo file =================
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-2-MBE: Multiple bit error detected at 0xC09F4D38
Jan 14 05:33:50.822 GMT+7: %C7600_MEM_ECC-3-SYNDROME_MBE: 8-bit Syndrome for the detected Multi-bit error: 0x0
05:33:50 GMT+7 Sat Jan 14 2012: Unexpected exception to CPU: vector 1500, PC = 0xB7922BC , LR = 0xB792250
==================== Show Version ======================
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 10-Feb-11 19:27 by prod_rel_team
ROM: System Bootstrap, Version 12.2(33r)SRD5, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15.1(1)S1, RELEASE SOFTWARE (fc1)
[Code]...
View 3 Replies
View Related
