Cisco Wireless :: Wired Client Behind 1262N WGB Not Pingable
Jan 26, 2013
A Customer has a 1262N-WGB connected via LWAPP to a 5508 Controller.(7.2.x.x)Behind the WGB they have a no-name switch and connected to that two D-Link cameras.I am not able to ping these cameras. When I connect my laptop to that switch it is no problem. I am getting an IP and the laptop is pingable.The cameras are also getting an IP, I see them for 5 to 10 seconds as clients on the WGB on the WLCI tried all that stuff with "passive client", arp entry on WLC and Layer 3 switch, but still no luck!Also the entry on the WGB "bridge 1 address MAC fortwarf Gig 0Solutions?Sent from Cisco Technical Support iPad App
View 6 Replies
ADVERTISEMENT
Jul 3, 2012
I'm having an issue with the 5508 management port .. I can't seem to ping it from the switch connected to it .. ( the Show cdp command shows that the two can see each other .. but no ping is possible ! [code]
View 4 Replies
View Related
Aug 27, 2012
I have a Cisco Wireless LAN Controller WCL2112 model. It's currently plugged into an HP Procurve switch on a trunk port. That HP switch is plugged into my Cisco stack on a trunk port. I can reach the WCL just fine through the LAN. But when I plug the WCL directly into the Cisco stack on a trunk port, I can't reach the WCL at all, unless I connect to it over wireless. The interface shows it's conneccted and up/up. But no communications are sent across the line. I did a wireshark and can see only ARP request from the WCL. The trunk port on the stack is set to:
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
switchport mode trunk
The WCL has 3 VLAN's on it and the SSID of VLAN 1 is our office wireless. If that matters. .The Cisco Stack is 4 switches. cisco WS-C3750X-48P
View 3 Replies
View Related
Jan 16, 2013
I have a Cisco 5500 Software Version 6.0.199.4. Today I've been able to succesfully add a few newly purchased 1242G APs to my WC so I know everything is setup properly. They got the proper DHCP info and I was up and running in a few minutes.
I'm now trying the same thing with a newly purchased Air-Lap1262N-a-KP
I can read the bootup because I'm attached to it on the console.I see that it gets the proper IP#
But then I keep getting a "failed to decode the discovery response" error.
[code]....
View 9 Replies
View Related
Oct 23, 2010
my modem/router WAG320N works ok but wireless client can't see wired and vice versa. they are in the same network (192.168.0. ), using the same 255.255.255.0 mask, same workgroup and yes firewalls allowing all packets in and out. IP addresses are form DHCP.
internet sharing works ok, but when im trying to play any game on LAN wireless clients can see them self but not the wired one. when im trying to ping wireless client from a wired machine it doesn't work either.
what's intresting in a DHCP reservation or ARP table (in router setup) i can see both wired and wireless clients. but still they can not see each other.
View 8 Replies
View Related
Oct 26, 2011
We have a couple of autonomous 1262's that I'd like to get configured. I would like to put the Ethernet interface out on our Internet subnet and have the clients get a RFC 1918 address from the radio's. Our little Linksys is setup this way and the clients are PAT'ing off the Ethernet interface when they go to the Internet.
Is this possible with these guys or do I have to put the AP ethernet interface into the same subnet with the DHCP scope? I don't have enough Internet IP's to hand out to every wireless client.
View 15 Replies
View Related
Jun 4, 2013
can we configure ip address air lap 1262N-A-K9 via CLI?
View 6 Replies
View Related
Oct 15, 2012
does wlc 2504 support air-ap 1262n-e-k9.if yes does the air-ap1262n need any upgrade or sometine to join the controller,this is versions & image for both AP & WLC2504: [code] and the below what i configure for my topology WLC connected to switch by Trunk linke allow all vlans.AP connected to switch by access mode for vlan 20. the IP address sechma :
1- WLC 192.168.10.1 , Gateway in switch 192.168.10.254 ( vlan 10 )
2- AP 10.10.10.2 ( DHCP ) , Gateway in switch 10.10.10.254 (vlan 20) DHCP server its the switch is self , we use the option 4
View 4 Replies
View Related
Nov 21, 2012
I have many 1262N and 1031AG APs. when the client is connected to the AP 1262N the performance is slower than it is connected to AP 1031AG (with more clients) in 2.4GHz.
View 3 Replies
View Related
Mar 8, 2012
I got new cisco aironet 1262n Dual band Access-point running IOS version 12.4(23c)JA .my question is does this access-point support 40 MHz channel width on the 2.4 Band on any IOS version as the command "Channel width" under interface dot11radio 0 allow only 20 MHz
View 18 Replies
View Related
Jan 8, 2013
I want to use the AP on a little office and I think this antenna give a good performance,
View 7 Replies
View Related
May 2, 2013
why my AIR-AP1262N-A-K9 will not boot all the way. It will get all the way to initiating the interfaces and stop. I can never get to controlling the cli. This is my first time with a cisco ap but from everything that I read it seamed very easy.
This unit from what I understand will work all on its own with no controller. Hence it is called a "standalone" model. Yet it seems to be looking for something to finish during the boot. Below is the out put during boot. The last line is where it stops.
r WRDTR,CLKTR: 0x8200083f 0x40000000r RQDC ,RFDC : 0x80000033 0x00000212
using eeprom values
WRDTR,CLKTR: 0x8200083f 0x40000000RQDC ,RFDC : 0x80000033 0x00000212
[Code]......
View 7 Replies
View Related
Mar 6, 2013
I would like to start setting up a Cisco Wireless Lan Controller 5508 with some Cisco 1262n AP's. How to start setting this to take advantage of having this wireless lan controller? I have a DHCP server, a Cisco 6509, and Cisco 3750g that connects the access points. I have Vlan 50 for wireless access points.
View 7 Replies
View Related
Mar 5, 2013
I have two 1262N access points with 5Ghz antennas, and I have configured one of them as a root bridge and the other as a non-root bridge; both using the same ssid. I have enble both dott11Radio interfaces on each access point. The problem I am having is that they do not associate. I have not configured them for any encryption or security. I just want to make sure the connect before I add any other configuration. Is there anything else that I need to configure to make them associate.
View 1 Replies
View Related
Apr 9, 2012
I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
View 2 Replies
View Related
Apr 20, 2013
We have a cisco 2811 router with 2 ADSL interfaces. One dialer interface is used for internet and another dialer interface is used for VPN.
The dialer interface that is used for internet purpose is "Dialer 1" and the VPN is "Dialer 2".
The route looks like this: ip route 0.0.0.0 0.0.0.0 dialer 1
Basically, I am able to the ping the external IP address associated with the Dialer 1 interface, however, I cannot ping the external IP address associated with Dialer 2.
View 5 Replies
View Related
May 1, 2012
I have an Internet Gateway with dual homed to 2 ISP's terminated in 2 different routers in my end. My end routers are 7606 routers.
I have a WAN link from Router 1 to ISP1 and from Router 2 to ISP2.
Router 1:
-------------
int Gi1/1
description " Link to ISP1"
ip address x.x.x.142 255.255.255.252
x.x.x.141 is configured in ISP end router.
The problem I m facing is that I m not able to ping x.x.x.142 from this router. But x.x.x.141 is pingable.
Also when I check from any internet route server, I m able to ping both x.x.x.142 and x.x.x.141.
View 1 Replies
View Related
Jul 17, 2012
I am having an issue where the GRE tunnels are up/up but are not pingable. The GRE tunnels are on a cisco 1811 and cisco 2811 routers The tunnel source and destination IP addresses are private addresses. These private addresses are pingable to each other and they are connected via IPSEC. The IPSEC tunnels are generated from the ASA to which the cisco routers connect. Probably the tunnels are up/up because keepalives are not configured. But I am still not able to see why I cnt ping the end points. The ACL for IPSEC in ASA includes the "permit gre host <Private IP 1> hist <Private IP 2>" commands.
View 2 Replies
View Related
Feb 21, 2013
I am trying to enable the workgroup bridge mode on the 5ghz 802.11N radio of a Aironet 1262N, but when I select the workgroup bridge mode from the GUI the radio becomes disabled. If I select the Access Point role from the GUI then the radio instantly becomes enabled. The same thing happens if I attempt the same procedure with the 2.4ghz radio as well. I can get the radios from both bands enabled if I select the Access Point role. I made sure to check that both radios were not set to workgroup bridge as well. I am running 12.4(25d)JA1 code on the AP. This is my first time working with this type of AP.
View 2 Replies
View Related
Oct 12, 2011
An 1841 is conencted to the internet by DSL, it works fine. I have added it to the 10.98.8.x subnet off a 3750 switch.When I connect other devices to the same switch port, I can ping/browse to them fine, but when I connect the 1841 I can only ping it from the 3750, not another subnet connected to the same router. [code]
View 2 Replies
View Related
Apr 27, 2008
How to setup quickvpn to work with RVS4000.
View 9 Replies
View Related
Feb 14, 2013
I have setup a WiFi bridge using two Cisco 1262n AP. I was able to get the bridge up and running for a little while. But soon after I plugged in a switch on the non root side of the bridge, the LAN on the root side started slowing and user were getting disconnected from the network. I suspect the Spanning Tree issue with the Bridge.
Couple questions:
I am using both the 2.4 and the 5Ghz bands for the Bridge. I assume that this was OK and was needed to get the highest throughput, right?
I was making an assumption that the AP would take into account the possible spanning tree issues automatically when both bands are used in the same bridge. Is assumption correct? If not what is the correct configuration for spanning tree on a wireless bridge that uses 2.4 and 5 bands?
View 2 Replies
View Related
Feb 2, 2012
I connect to my RVS4000 VPN router using QuickVPN. Very useful.
Sometimes I am not near my laptop and need to check data.
Is there a QuickVPN or compatible client for a BlackBerry Torch 9850, even if it's only functional when connected to WiFi?
View 1 Replies
View Related
Jan 31, 2011
Most devices pass a client name to DHCP when requesting an IP, but some like my smartphone, do not. When a device does not pass a client name garbage is entered as the name of the client name.The first is that when you use the Web Admin pages, and select Status/Local Network/DHCP Clients, the table will not display any clients because there is an error on the page. If you right click and View Source from the browser, you will see all the client entries are there and one of them will have garbage (unprintable characters) for the client name.The second and more serious issue is that the internal DHCP table once corrupt is unstable. I've had my BEFSR41 reboot because of the corruption and then I get IP conflicts on my LAN because the DHCP starts handing out in-use IPs.I'm on hardware version 4.3 and the latest firmware Ver.2.00.4 Build 8 (which is very difficult to install without bricking the router). BTW, when I use a WRT54GL router with the smartphone, it is properly handled by the DHCP and shows a blank client name, not garbage.
View 3 Replies
View Related
Jun 1, 2011
I am attempting to access a VPN hosted on Windows 2003 Server using my Windows 7 SP1 / 64 bit laptop. I can establish the connection and even open Outlook and connect to the exchange server on the remote network. It seems that whenever I try to move files up or down or open Internet Explorer, the following sequence of events happens:
1) Connection between my local router (BEFRS41) and the internet is dropped.
2) The IP address on my local network adaptor changes to an unknown number (169.254.180.72) - is normally 192.168.1.104
3) The VPN connection drops and attempts to re-dial, but of course fails because my connection tot he internet has been broken.
Since I'm accessing rather than hosting the VPN, I'm not sure if I have to adjust any of the router settings.
View 3 Replies
View Related
Jun 26, 2011
On the BEFSR41 v1 series and WRT54G series, what is the maximum value for the DHCP "Client Lease Time (in minutes)?" It seems that 2^16 -1 (65535) minutes is the max. This is about 45 days. has the max value changed with newer versions of these devices?
View 1 Replies
View Related
Oct 19, 2011
I have a setup involving 3 clustered AP541 running off a sg300 switch. The wireless network setup VAP has one entry for vlan 1 with station isolation disabled. Is there anything more I need to do to allow one wireless client to ping another wireless client - am I missing something - i assume this is possible.Needless to say wireless clients can ping non wireless clients and vice versa quite happily. Everything is running with factory default settings more or less.
View 4 Replies
View Related
Mar 20, 2012
i have a question about tunneling a software EasyVPN client to a client ASA Network. It looks like this:
EasyVPN Server 192.168.202.0/24 Network extension mode to Client EasyVPN ASA 192.168.1.0/24 This works fine in both directions. But now i want to connect the client ASA network via EasyVPN software client from outside. The user are already able to connect to the ASA Server on its static outside IP obtaining an IP from a 192.168.21.0/24 pool. This works fine. But how am i able to connect to the 192.168.1.0/24 network from this client?
View 5 Replies
View Related
Apr 18, 2013
how to make the java SSH thin client applet bigger in SSL VPN Clientless portal?It works and all that but the window is literally half the size of the monitor and unworkable. You can't even hit tab! (tab moves focus around the browser...)I am using the latest java applet (Oct 2012) and ASA OS 8.4(5)
View 3 Replies
View Related
Apr 21, 2013
Do the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.
View 4 Replies
View Related
Sep 23, 2012
I purchased and set-up the EA4500 on Thursday. Friday my ISP (Charter) was out and worked on connection for over 2 hours due to slowness issues. Connected directly to modem I get normal ping times on whichever computer is connected. When I get the computer connected by the router (hard wired) I get very long ping responses up to 900ms. They are all over the place 30ms (I can live with that), up to the 900's. I contacted Linksys support last night, who had me update to the cloud firmware and change MT U to 1300, have not noticed a difference. I did end up doing a hard reset on the router last night after I lost tech support. We were disconnected with router rebooted, and I didn't have the patience to connect again last night.
It was so slow on my work computer, a pint to yahoo timed out. The computers connecting to router are
XP SP3 (mine)
Win 7 Home (IPV6 turned off)
Work laptop that uses VPN and VOIP
View 5 Replies
View Related
Sep 19, 2011
I have an e2000 wireless router and have several devices connected by ethernet cable including private data on an external hard drive. I am planning to allow a tenant in another building connect via an ethernet cable connected to my router. Can I limit that computer (tenant's computer) from accessing all other devices connected by ethernet cable to my router? I know can password protect wireless access and limit access to the internet that way -- but my question is specifically to connections by ethernet cable.
View 1 Replies
View Related
Oct 11, 2012
My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies
View Related
