Cisco Wireless :: Does WLC 2504 Support AIR-AP 1262N-E-K9
Oct 15, 2012
does wlc 2504 support air-ap 1262n-e-k9.if yes does the air-ap1262n need any upgrade or sometine to join the controller,this is versions & image for both AP & WLC2504: [code] and the below what i configure for my topology WLC connected to switch by Trunk linke allow all vlans.AP connected to switch by access mode for vlan 20. the IP address sechma :
1- WLC 192.168.10.1 , Gateway in switch 192.168.10.254 ( vlan 10 )
2- AP 10.10.10.2 ( DHCP ) , Gateway in switch 10.10.10.254 (vlan 20) DHCP server its the switch is self , we use the option 4
View 4 Replies
ADVERTISEMENT
Nov 28, 2012
what is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
View 8 Replies
View Related
Aug 28, 2012
I would like to get it clarified, that Cisco WLC 2504 running the code ( 7.2.110.0 ) does support IPv6 or not ?
From Cisco Documents they are asking to enable IPv6 support under WLAN > Edit Page, and Enabling mulicast on Ethernet Multicast Mode under Controller > General.
But from the GUI am not able to find the above two field, Even in Interface i created under Controller > interface is not accepting IPv6 address. I am able to configure IPv6 ACL .
Is any deployment document is available to show different scenarios with configuration.
Note - Am using Access point AIR-LAP1262N-N-k9
View 1 Replies
View Related
Jun 11, 2013
Does the 2504 Wireless Controller support cad or jpg drawings? I have not been able to find in any of the menus.
View 1 Replies
View Related
Aug 10, 2012
I have a customert that needs to support 200 laptops over 16 classrooms with scalability to 400 laptops. I have a heatmap design to cover this with 22 1042 access points. Does any one know what features the 5508 has over the 2504? By reviewing the data sheets, the biggest feature difference is better support for mobility, which not a need for this deployment as they just wheel a cart of laptops into a classroom and fire them up. Also, does the 2504 support LAG across the four gig interfaces?
View 1 Replies
View Related
Dec 3, 2012
Is NPS (windows 2008R2) supports EAP-TLS? I've built an NPS to authenticate wireless clients (WLC 2504). But in the EAP types I only see EAP(PEAP) this only requires a certificate on the server side.
I want the clients also should have a certificate, for that the NPS should support EAP-TLS
View 1 Replies
View Related
Jun 11, 2013
I attempted to assign a User Roles template to a## 2504 controller and if failed with message stating controller version not supported. My current WCS version is 7.0172, if I upgrade to the lastest version will that resolve the template issue?
View 4 Replies
View Related
Aug 28, 2012
i have stand alone cisco 1130g ap ,and wlc 2504. wlc 2504 support this ap or not ?
View 3 Replies
View Related
Jul 27, 2012
Question about cisco 2504 wireless controller, is it support cisco 1552E outdoor access point? If NO provide me the correct series/model.
View 9 Replies
View Related
Jan 16, 2013
I have a Cisco 5500 Software Version 6.0.199.4. Today I've been able to succesfully add a few newly purchased 1242G APs to my WC so I know everything is setup properly. They got the proper DHCP info and I was up and running in a few minutes.
I'm now trying the same thing with a newly purchased Air-Lap1262N-a-KP
I can read the bootup because I'm attached to it on the console.I see that it gets the proper IP#
But then I keep getting a "failed to decode the discovery response" error.
[code]....
View 9 Replies
View Related
Oct 26, 2011
We have a couple of autonomous 1262's that I'd like to get configured. I would like to put the Ethernet interface out on our Internet subnet and have the clients get a RFC 1918 address from the radio's. Our little Linksys is setup this way and the clients are PAT'ing off the Ethernet interface when they go to the Internet.
Is this possible with these guys or do I have to put the AP ethernet interface into the same subnet with the DHCP scope? I don't have enough Internet IP's to hand out to every wireless client.
View 15 Replies
View Related
Jun 4, 2013
can we configure ip address air lap 1262N-A-K9 via CLI?
View 6 Replies
View Related
Nov 21, 2012
I have many 1262N and 1031AG APs. when the client is connected to the AP 1262N the performance is slower than it is connected to AP 1031AG (with more clients) in 2.4GHz.
View 3 Replies
View Related
Mar 8, 2012
I got new cisco aironet 1262n Dual band Access-point running IOS version 12.4(23c)JA .my question is does this access-point support 40 MHz channel width on the 2.4 Band on any IOS version as the command "Channel width" under interface dot11radio 0 allow only 20 MHz
View 18 Replies
View Related
Jan 26, 2013
A Customer has a 1262N-WGB connected via LWAPP to a 5508 Controller.(7.2.x.x)Behind the WGB they have a no-name switch and connected to that two D-Link cameras.I am not able to ping these cameras. When I connect my laptop to that switch it is no problem. I am getting an IP and the laptop is pingable.The cameras are also getting an IP, I see them for 5 to 10 seconds as clients on the WGB on the WLCI tried all that stuff with "passive client", arp entry on WLC and Layer 3 switch, but still no luck!Also the entry on the WGB "bridge 1 address MAC fortwarf Gig 0Solutions?Sent from Cisco Technical Support iPad App
View 6 Replies
View Related
Jan 8, 2013
I want to use the AP on a little office and I think this antenna give a good performance,
View 7 Replies
View Related
May 2, 2013
why my AIR-AP1262N-A-K9 will not boot all the way. It will get all the way to initiating the interfaces and stop. I can never get to controlling the cli. This is my first time with a cisco ap but from everything that I read it seamed very easy.
This unit from what I understand will work all on its own with no controller. Hence it is called a "standalone" model. Yet it seems to be looking for something to finish during the boot. Below is the out put during boot. The last line is where it stops.
r WRDTR,CLKTR: 0x8200083f 0x40000000r RQDC ,RFDC : 0x80000033 0x00000212
using eeprom values
WRDTR,CLKTR: 0x8200083f 0x40000000RQDC ,RFDC : 0x80000033 0x00000212
[Code]......
View 7 Replies
View Related
Mar 6, 2013
I would like to start setting up a Cisco Wireless Lan Controller 5508 with some Cisco 1262n AP's. How to start setting this to take advantage of having this wireless lan controller? I have a DHCP server, a Cisco 6509, and Cisco 3750g that connects the access points. I have Vlan 50 for wireless access points.
View 7 Replies
View Related
Mar 5, 2013
I have two 1262N access points with 5Ghz antennas, and I have configured one of them as a root bridge and the other as a non-root bridge; both using the same ssid. I have enble both dott11Radio interfaces on each access point. The problem I am having is that they do not associate. I have not configured them for any encryption or security. I just want to make sure the connect before I add any other configuration. Is there anything else that I need to configure to make them associate.
View 1 Replies
View Related
Apr 9, 2012
I want to connect two buildings. Let's call them Building A (main) and Building B.
„A“ is the main building and provides a wired LAN to an AAA server (192.168.1.2) and the WAN gateway (192.168.1.1). There I placed a 1262N with the IP 192.168.1.3 connected to the wired LAN and configured it as Root-Bridge. Let's call it AP01.
„B“ is a pretty large building and has a wired LAN from one end to the other end.
So I placed two 1262N there, each at one end.
The first 1262N is configured as non-root Bridge (AP02) and connects to the Root Bridge (AP01). The IP address of AP02 is 192.168.1.4.
The second 1262N is configured as Access Point (AP03) and connects to the non-root Bridge (AP02) via the wired LAN. The IP adress of AP03 is 192.168.1.5
My Questions:
1. Do I need tell AP02 about the AAA Server in Building A or acts AP01 like a AAA Proxy for AP02 because of it Root Bridge functionality?
2. How Do I tell AP03 that it should use AP02 as a gateway to building A?
View 2 Replies
View Related
Feb 21, 2013
I am trying to enable the workgroup bridge mode on the 5ghz 802.11N radio of a Aironet 1262N, but when I select the workgroup bridge mode from the GUI the radio becomes disabled. If I select the Access Point role from the GUI then the radio instantly becomes enabled. The same thing happens if I attempt the same procedure with the 2.4ghz radio as well. I can get the radios from both bands enabled if I select the Access Point role. I made sure to check that both radios were not set to workgroup bridge as well. I am running 12.4(25d)JA1 code on the AP. This is my first time working with this type of AP.
View 2 Replies
View Related
Feb 14, 2013
I have setup a WiFi bridge using two Cisco 1262n AP. I was able to get the bridge up and running for a little while. But soon after I plugged in a switch on the non root side of the bridge, the LAN on the root side started slowing and user were getting disconnected from the network. I suspect the Spanning Tree issue with the Bridge.
Couple questions:
I am using both the 2.4 and the 5Ghz bands for the Bridge. I assume that this was OK and was needed to get the highest throughput, right?
I was making an assumption that the AP would take into account the possible spanning tree issues automatically when both bands are used in the same bridge. Is assumption correct? If not what is the correct configuration for spanning tree on a wireless bridge that uses 2.4 and 5 bands?
View 2 Replies
View Related
Feb 16, 2011
can wireless router support up to 100 user including support network printer
View 1 Replies
View Related
Mar 2, 2013
Why a 2504 Poe? If it can not be used for AP.
View 10 Replies
View Related
Jan 22, 2013
I'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies
View Related
Aug 29, 2012
I've problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.
View 14 Replies
View Related
Aug 15, 2012
I have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range. How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID. The two controllers are in a mobility group.
View 4 Replies
View Related
Jul 12, 2012
If we update our ios on WLC do we have to add the certificate for AP's again or we don't need to do that.
View 4 Replies
View Related
Mar 13, 2013
Some time ago I updated a WLC, model 2504, from version 7.3 to 7.4.100.0. I also update the FUS (Field Upgrade Software) to the latest release, 1.8.0.0. Now I need to downgrade the WLC back to 7.3 version.
My doubt is: Can I just take the normal processes and downgrade the WLC back to 7.3, even with the FUS in version 1.8.0.0?
View 5 Replies
View Related
Jun 10, 2013
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
View 15 Replies
View Related
Aug 2, 2012
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies
View Related
Mar 12, 2013
I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies
View Related
Jul 3, 2012
I've got a 1524 ap and it wont join my 2540 WLC. The messages I see in the WLC is RADIUS authorization is pending for the AP. I've added the MAC address of the ap under AP Policies using MIC. I dont have a radius server either so not sure how to tackle this one.When I run debug capwap events enale under the wlc I see the following messages:Discarding discovery request in LWAPP from AP supporting CAPWAP.
View 35 Replies
View Related
