Im having problem configuring policies for limiting traffic on subinterfaces on cisco Router 7606-S. I have configured:
[code]...
So for egressQOS , i want to configure with police, not shape (for the memory reason).
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies View RelatedWe are planning to configure the ipv6 PBR on our 7606 routers. We have configured the route-maps successfully .but when we tried to apply those on interfaces we are facing an problem .
when we trying to give command # ipv6 policy route-map <route map name> . we are unable to find policy command option in the command list.
IOS Version : c7600rsp72043-advipservicesk9-mz.122-33.SRE3.bin.
How the police flow command ( see below) works only in the 6500's platform? Can it apply in 3745 router?
View 2 Replies View RelatedI have a 7606 router with sup 720-3bxl. IOS has been crashed recently and i can use only Roman mode now. Ive tried to upload ios image using tftp server but the command tftpdnld id not available in this router. I don't know why. Then i tried to boot from flash disk but finally it also shows an error like
System received a Software forced crash signal= 0x17, code= 0x24, context= 0x42359674 PC = 0x402d248c, Cause = 0x1020, Status Reg = 0x34008002
How to make the router in running condition.
configuring policy based route for my cisco router?Basically, I have a 2811 cisco router with 2 ADSL ports. 1 port is for iiNet line and another port is for Telstra line.I want to configure a policy based route on the router so that:Any traffic coming from 1 internal IP (i.e. 172.16.x.1) will go through iinet line (i.e. Dialer 0) interface.Any traffic from rest of the office will go through the Telstra line (i.e. Dialer 1) interface. Is there any easy way to configure this policy based route?
View 8 Replies View RelatedI configure my Cisco ACS5.2 using Command set policy and providing Shell access 15.I allow user only “show * ” command.It works fine with Telnet. User Group cannot execute any command apart from “Show * ”But when I connect the device using Console user group has full permission on the devices.I believe Command set policy is not working on Console. Is it normal behavior or do I need to update some changes in ACS or Network devices ?
My network device configuration is as below :
tacacs-server host 10.x.x.x key test123
tacacs-server host 10.y.y.y key test123
tacacs-server timeout 1
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 1 default start-stop group tacacs+
[code].....
I am facing issue while configuring service-policy output command in Cisco 7609-S router with c7600s72033-adventerprisek9-mz.122-33.SRE2.bin IOS. However, in the same series router having IOS c7600s72033-adventerprisek9-mz.122-33.SRC6.bin is supported service-policy output.Both the switch have WS-SUP720-3BXL SUP.
View 2 Replies View Relatedhow to map my command shells that I created to the access policies under Default Device Admin/Authorization. All I get an option for is Shell Profile but not commands. See attached doc.ACS 4.2 was easy.. I would just create a command set and apply to a group.
View 5 Replies View RelatedI have been looking around and I can not find the " crypto isakmp policy " command on this Cisco Router 1941. I just wanted to setup a regular IPSEC Lan to Lan tunnel and surprise, the command is not there. Do I have the wrong IOS? I thought that a K9 image would do the trick. [code]
View 2 Replies View Relatedi would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies View Relatedhow can I configure policy NAT on ASA5510. I would like to do the following;
9.1.1.9 NAT to 10.1.1.9
If source IP = 1.1.1.1
then NAT to = 10.2.2.9
the rest NAT to = 10.1.1.9
The issue is I want 1.1.1.1 NAT to 10.2.2.9 when access www.example.com. The rest NAT to current NAT.
I need to attach a QOS policy to a layer 2 WAN interface between two sites. This is actually an extended LAN circuit with 500Mb/s of allocated bandwidth. The interfaces are Gigabit so I want to make sure I don't attempt to transmit traffic faster than 500Mb/s. What is the best way to implement an outbound QOS policy that sets the minimum and maximum speed to be the same? This policy will be implemented on a 4900M with the 20 port GigE module
View 3 Replies View RelatedI want write comment for command when i config switch .i want when use show running display comment .
View 1 Replies View RelatedSetup:
Cisco 886VA-K9
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(4)M3, RELEASE SOFTWARE (fc2)
This router has two VLAN's on one Ehternet interface
VLAN1: data
VLAN2: voice
The WAN connection is a regular DSL line with PPP.
Modem FW Version: 120306_1254-4.02L.03.B2pvC035j.d23j
Modem PHY Version: B2pvC035j.d23j
Output of show interface brief:
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM up up
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
[code]....
We all know you can't manage data traffic on the internet since your not in control of both sides of the link. So only queuing would not be a good practice IMHO. I was thinking on just rate-limit or police data-traffic so Voice always has bandwidth available when needed. I've did tried to rate-limit on the ATM0 interface, but no luck. Voice was still very bad.
My question is: where to rate-limit the data traffic? On the VLAN interface, the ATM interface, DIALER interface?
I had insatalled the ACS 5.2 on Vmware . As per my requirement i need to configure a user to restricted privilege so that he should be able to execute only the below commands on the switch .
-Show ver
-Show interfaces
-Show ip Interface Brief
-Configure terminal
-Interface <interface name >
-Shutdown
-No shutdown
The users should not be authorized to execute any other commands than above listed one .After the configuration i was not able to restrict the config mode commands . Once the user is authoized for Configure terminal access he will have full access on the device. How to configure the command set only to allow interface access and he should be able to apply Shutdown and No shutdown command .
I have a cisco air lap 1522 but i have problem with it! I cant use config command in cli ? And i cant assign ip address to ap.
View 19 Replies View RelatedI have two questions about ZBF on ASR1000 with Firewall and Flexible Packet Inspection license:
1 is IPv6 supported?
2 can I use police action in an inspect rule? I want to limit some protocols to low bandwidth. There is no police command in ZBF policy map.
I need to put a FWSM and a line card WS-X6148A-GE-TX to a router 7606. The FWSM version is 3.2(13). The router is running IOS 12.1(18)SXD3. The Cisco document here says the required IOS for router 7606 is 12.2(18)SXF or higher. I have downloaded the IOS 12.2(33)SRD4 and loaded it to the flash card. When I turn the router on, it doesn't load the new IOS and goes to rommon. Which IOS I should use to make the router 7606 work and accept the FWSM.
View 2 Replies View RelatedI have an AIR-LAP1242AG-A-K9. Straight out of the box I thought it would have the GUI functional but this is not the case. I am brand new to Cisco products so it is taking me a while to get use to them and to TelNet but from what I have read in about 6 different manuals none have explained how I can access the configure terminal command when It doesn't show up. I am in privileged mode with access of: AP001c.588e.a266#show privilege. Current privilege level is 15.If I can't get into global configuration mode I cant enable the GUI, turn on the wireless.
View 6 Replies View RelatedI have a C3825, and have been using standard ACLs and a PBR to route certain HTTP traffic via an alternative default gateway:
route-map RTRMAP-OfficeLAN permit 10
match ip address RTRMAP-OfficeLAN-toADSL
set ip next-hop x.x.x.x
This is working absolutely fine, and as expected, all traffic matching the ACL is being sent to x.x.x.x However, we have recently expanded our network, and I am now receiving various networks via BGP from various sources. All BGP incoming via iBGP is tagged in communities:
Community (expanded) access list 100
permit 37xxx:100
Community (expanded) access list 200
permit 37xxx:200
Community (expanded) access list 300
permit 37xxx:300
[code].....
All communities are also matching prefixes when executing either 'sh ip bgp community 37xxx:100' or 'sh ip bgp community-list 100' What I am trying to achieve, is create an EXCEPTION for the policy route. Traffic matching the community lists, must be forwarded based on the routers routing table, whilst traffic maching the ACL, must be sent via the policy route...
route-map RTRMAP-OfficeLAN permit 5
match community 100 200 300 400 500
!
route-map RTRMAP-OfficeLAN permit 10
match ip address RTRMAP-OfficeLAN-toADSL
set ip next-hop x.x.x.x
My logic dictates to me that the above should work, but looking at the route-map, I get matches on seq 5 and pacets are exiting the route-map as expected (first matched). However no traffic that does NOT match community 100,200,300,400 or 500 and that DOES match the RTRMAP-OfficeLAN-toADSL never matches.
The counters on the route-map for seq 5 is increasing, but no counters are increasing at seq 10.. It's almost as if seq 5 is matching all traffic.
I have a 7606-S router ( non redundant ) with SUP32 and i wand to replace it with RSP720-3C-GE , i am asking about the procedure?
-shall i switch off the router ? or just removeSUP32 and insert RSP720 ?
-are there any steps should i do before the upgrade ?
-i am planning to take the router out of service during the operation, how much down time it will be ?
ES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
what is the equivalent command to configure on the Nexus 5596? OS version 5.1(3)N2(1) Catalyst 45k ip igmp snooping vlan 1036 mrouter interface Po20
View 1 Replies View RelatedAny know how to close these open ports on my Cisco 7606 router? Any know what these TCP ports are used for?
:
49 - Not sure what this one is other than what IANA reports about TCP port 49
4510
4509
2222
:
I'm sure I could add an ACL to block communications to my router based on this ports but would rather figure out how to close 'em so this already overloaded router doesn't have additional processing.
I'm working with AnyConnect for the first time (my prior experience is with IPSec client) and I have multiple remote users who connect to a 5520 via AnyConnect client; they need to print to each others' shared printers but currently have no connectivity between each other.
Can I configure the 'intra-interface' command to enable connectivity between remote clients, or is there more that needs to be done to enable this, presuming that it can be done at all?
In our datacenter we have a 3750 stack with IP base image. I have enabled PBR and reloaded the switch. Show sdm prefer says i am using default template. The reason i want to use PBR is that we have 2 firewalls on the same work and want to be able to have granular control over which gateway out of the network they use but still be able to access all internal resouces accross wan and locally.
Created access list to identify traffic:
access-list 10 permit 10.2.3.59 (test workstation on vlan 3)
Created policy:
route-map TestASA permit 10
match ip address 10
set ip next-hop 10.2.0.3
Assigned policy to the user vlan3:
ip policy route-map TestASA
Results:It changed the default gateway to the above gateway but i could not access any resources on any other vlan, could not access resouces accross wan.
I need to create a policy to provide only 4 Mbps bandwidth for mail out of 16 mbps pipe terminated on 7606 router (at Datacenter) having WS-SUP32-GE-3B.But I can't create policy with bandwidth percent,even exact value with priority command does not work. When I am going to enter service policy output command at interface it is showing as"priority command is not supported in output direction for this interface Configuration failed!" All I want to restrict bandwidth at backbone link for mail traffic. From all remote locations use to access mail server over the same link.
View 1 Replies View Relatedhigh CPU on newly installed 7606.
CPU utilization for five seconds: 61%/59%; one minute: 62%; five minutes: 63% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 578 5856 9392486 0 0.55% 0.50% 0.50% 0 IP SLAs XOS Even 231 90364 576908
[Code]......
I tried to reboot manually and I changed the slot but the same behavior:
%SYS-SP-3-LOGGER_FLUSHING: Systema pausing to ensure console debugging output
%OIR-SP-6-CONSOLE: Changin console ownership to route processor
*** System received a Software forced crash ***
signal= 0x17, code= 0x24, context= 0x430213e4
PC = 0x4038c124, Cause = 0x1020, Status Reg = 0x34008102
who to configure the interface of cisco 7606 router. As it is not getting up by doing normal configuration like "no shut"? iterface and line protocol both are down.
View 1 Replies View RelatedOur Router 7606 is in a problem with high CPU Utilization. We are using one EBGP and one IBGP session. We are also running OSPF with area 0 between two IBGP router to exchange few local networks. When bandwidth cross 100 MB than only CPU use become 100%. when bandwidth consumption is 80MB CPU use become 80% end so on.
Out put is when bandwidth consumption is 34MB
CPU utilization for five seconds: 44%/43%; one minute: 42%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
78 44 9625 4 0.39% 0.03% 0.00% 2 Virtual Exec
13 40 375 106 0.07% 0.00% 0.00% 0 ARP Input
30 116 1098 105 0.07% 0.01% 0.00% 0 IPC Seat Manager
[code]....
I have a fresh piece of 7606-S router, i am planning to install a new IOS ( 15.2.4S or 12.2.33-SRD8 ) SIP-200 / RSP720 moduls ... would ypu plese provides me a configuration guide for installing IOS for 7600 serise router.I have the image on TFTP server.
View 3 Replies View Related