i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 RepliesI have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies View RelatedI am having some difficulties on finding information on how to setup two Cisco 1252 autonomous access points, via the command line. I am not having any luck finding steps on how to go about doing this and was curious if any one would be willing to give some insight. I am working on taking two of them setting one up as the root bridge and the other as non-root.
View 3 Replies View RelatedOn my old 2511 access server, I could issue "clear line x" to close a session on an existing line.this doesn't seem to work on my new 2600XM with NM-16A access server (12.3(20)IOS), any command in newer IOS?
View 4 Replies View Relatedwe just bought a 2921 with the following modules: 4 port clear channel T1/E1 HWICSM-ES3G-24-P: EtherSwitch.I read some CISCO documents, and not be able to find what I need. I would prefer all instructions from you are for CLI interface.This is my first time to deal directly with T1, WIC and 2921 etc. The following is what I get from ATT, IP masked IP Address Block IP Address: 20.20.20.136/29 WAN Link Details: WAN Link IP Address:13.13.13.92 AR Serial INT IP Address:13.13.13.93 CR Serial INT IP Address:13.13.13.94 WAN Link Subnet Mask:255.255.255.252
A: how do I configure T1, what does "AR, CR" stands for, and do I need to use both IP addresses? What is the WAN Link IP for?
B: We have two T1 lines, so I should plug them both to the WIC, say port 0 and port 1, how to configure them?
C: how do I access the firewall from the command line?
D: I followed T1/E1 HWIC installation guide, and as soon as I add channel-group to the controller t1, the serial interface went down?
how to open the Linksys E4200 command line interface? Ive tried using telnet but i get this message:Could not open connection to the host, on port 23.
View 3 Replies View RelatedI had insatalled the ACS 5.2 on Vmware . As per my requirement i need to configure a user to restricted privilege so that he should be able to execute only the below commands on the switch .
-Show ver
-Show interfaces
-Show ip Interface Brief
-Configure terminal
-Interface <interface name >
-Shutdown
-No shutdown
The users should not be authorized to execute any other commands than above listed one .After the configuration i was not able to restrict the config mode commands . Once the user is authoized for Configure terminal access he will have full access on the device. How to configure the command set only to allow interface access and he should be able to apply Shutdown and No shutdown command .
We have lots of new lap1041 need be set static IP Adress, hostname, Controller Adress via command line, but when use command (capwap ap hostname) to set hostname , always give us command disabled, we used command:clear capwap private-config, but it does not work, why?
View 4 Replies View RelatedI want to know if WAG325N supports cisco's IOS so that i can configure it using command line interface? Is it possible?If not, how would i change ethernet interface speed setting so that it can support 100 mbps of speed. Because when i connect through LAN i'm always getting a full dulplex 10 mbps LAN connection automatically.
View 1 Replies View RelatedHow to configure to use Router with Lease Line ?
1.connect a computer to the wan port-router
2.give the ip in the url-------- 192.168.1.1( by default )
3.enter username and passwrd
4. then in the GUI mode
5. go to the wan setting ...router
6.there put the live ip and the gateway and the dns....aircel detail....
7.go the lan setting and put the lan ip series do nt configure dhcp go manually to all the nodes and put the lan ip u have 4 lan ports
8.out of 4 port ...port 1-- connect the dialler...in lan port
9.and in port 2 connect to (switch) a unmanaged switch frm where u can connect to your lan
10.if in the lan setting u hv given the ip 192.168.1.1
11.then put ur dialler ip 192.168.1.2
12. and local lan machine will tk the ip frm 3 onwards
13.nw if u want to authenticate ur dialer in our voip gateway then give the ip of ur router
15. 192.168.0.1 will be the ip of the lan setting in the router
16. and this will act as a gater to ur local machine gateway
simple configuration of a 2801 Router. I have 2 internet providers with static ip's connected to F0/0 and F0/1 and one Vlan for LAN area. I would like to configure the router to use one primary line and just in case to use the back-up line. [code]
Now if detects that it hasn't cable link on the FastEthernet interfaces it's working. I'm using 2 wireless gateways to acces the internet each one connected on the 2 FaEth for simulating the providers. If i simulate an issue on the provider ( i've removed the sim from the wireless gateway) it doesn't pass on the second isp.I haved trying to configure with "IP Service Level Agreements " for failover / load balancing but the command "ip sla" is incomplete. I can't make an update of the IOS because the customer do not have an Service Contract with Cisco.
My grandma has a PC with Windows XP, she uses it only for Skype calls. can go in to her PC using command line from my PC? What commands should I use and what modifications to do on my grandma's PC? Should I ask permission from grandma's ISP (which is the same as mine)?
View 3 Replies View RelatedMy 3550 is always 2 characters short on the command line. So my global configuration mode will look like this:Switch3550(config Say I wanted to enabled ftp, it would look like:Switch3550(config)# ftp enab.
View 2 Replies View RelatedIm trying to get my head around my new cisco SG 300 switch. I have used the Linksys SRW range before and configured it using teraterm and method described in the link below:
[URL]
As im fimilar with this method and the commands ideally I'd like to use this on the SG 300 range as well. Failing that, is it possible to use another method which uses the same commands which can be easily copy and pasted for setting up multiple switches with the configuration?
I'm an ASDM 6.4 command line novice & I'm looking for the command to delete an unused vpn key, e.g. 'key1'.Or if there's a GUI method?
View 2 Replies View Relatedcommand to get running config of Cisco VPN 3000 concentrator.
View 3 Replies View RelatedI want to telnet a router (say) 1.1.1.1 with usename "user" and password "pass" in command line. i tried using....telnet 1.1.1.1 -l user ..........but not working
View 3 Replies View RelatedIs it possible to configure two AG241 adsl routers back to back via two wire line as a Lan to Lan network?
View 8 Replies View Related12 users, 3 servers, 5 smartphones/tables on the WiFi (existing AP), future VPN server (maybe 5 simultaneous inbound VPN connections at the most with at least one client using a Mac), Cisco Gigabit small business switch.Internet access, VPN connectivity, and firewall (reporting, close/open ports for custom applications as needed)I was originally going to select an ASA5505-50 user device for the above client. The device is highly regarded on the Internet, offers a command line interface, priced right for the budget and should perform all duties required by the client.However, the addition of the RV180W to the Cisco product line has me questioning my choice.
1)Does the RV180W offer a command-line interface?
2)Is the RV180W limited in the number of users it can support without having to purchase additional user licenses?
3)How are firmware/software upgrades handled with the RV180W?
4)What will the client be giving up if they choose the RV180W vs. the ASA5505?
Im having problem configuring policies for limiting traffic on subinterfaces on cisco Router 7606-S. I have configured:
[code]...
So for egressQOS , i want to configure with police, not shape (for the memory reason).
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
View 3 Replies View RelatedI have a cisco air lap 1522 but i have problem with it! I cant use config command in cli ? And i cant assign ip address to ap.
View 19 Replies View RelatedI have an AIR-LAP1242AG-A-K9. Straight out of the box I thought it would have the GUI functional but this is not the case. I am brand new to Cisco products so it is taking me a while to get use to them and to TelNet but from what I have read in about 6 different manuals none have explained how I can access the configure terminal command when It doesn't show up. I am in privileged mode with access of: AP001c.588e.a266#show privilege. Current privilege level is 15.If I can't get into global configuration mode I cant enable the GUI, turn on the wireless.
View 6 Replies View Relatedwe just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 Replies View RelatedI state that I'm very fast Voip router configurations, the problem is as follows: I need to configure a SPA3102 so that I hijack a line RTG via LAN / WAN or on a SPA2102 in the motion that the 2102 can receive and make calls.
View 4 Replies View Relatedconfigure Line Telnet on a Cisco SG300-10P switch.I am in config mode and enters line telnet,but when I do a show line,telnet still are disabled..
View 1 Replies View RelatedIs it possible to configure the switchports on a 6500 linecard before it has been inserted?
So for example, I have a 6509 with slot 9 free. I'm going to install a 48 port line card. Is it possible to configure those 48 ports before the card is inserted?
I want write comment for command when i config switch .i want when use show running display comment .
View 1 Replies View RelatedI need to configure a vpn on a Cisco WRV210 Wireless-G VPN Router - RangeBooster, i have five users that are going to connect to a file server. the file server access is all set i just need a step by step document to configure the vpn screens on the router.
View 1 Replies View Relatedam trying to find the configuration code and steps to configure a router to a wireless access point.
View 2 Replies View RelatedI previously put this is the 'Video over IP' discussions group, which is not getting any response.I have a 6509 and need to configure QoS on gig line cards that have 1P3Q8T queue structure. I've already got the mls qos configured, and have the correct class maps built for Voice, Video, and Signalling.(I'm not doing autoqos). I have only four classes; voice, video, signalling, and default (best effort).I need to configure the commands on the individual gig ports for the appropriate bandwidths as shown below:
1. 300 VoIP G711 calls x 100kbs/call = 30mbs of priority queue DSCP = EF (46) CoS = 5
2. 150 Video conference calls x 1.5mbs/call = 225mbs DSCP = CS4 (32) CoS = 4
3. 450 Signalling x 13kps/call = 5.8mbs (round to 6mbs) DSCP = CS3 (24) CoS = 3
4. Default class is not marked DSCP & CoS = 0
We have configured ASA 5510. We have configure Ethernet 0/0 ( Outside ) connected with ADSL line and Ethernet 0/1 ( Inside ) Local LAN. we have configured NAT and all the traffic is passing through outside interface. Now we have connected ethernet 0/3 ( leasedline ) interface with static public IP. Now we want to allow SMTP traffic to pass through from this interface.
How to configure it if we want our local lan SMTP traffic sending through new leased line ( Static Public IP ).
How do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies View Related