On my old 2511 access server, I could issue "clear line x" to close a session on an existing line.this doesn't seem to work on my new 2600XM with NM-16A access server (12.3(20)IOS), any command in newer IOS?
View 4 Replieswe just bought a 2921 with the following modules: 4 port clear channel T1/E1 HWICSM-ES3G-24-P: EtherSwitch.I read some CISCO documents, and not be able to find what I need. I would prefer all instructions from you are for CLI interface.This is my first time to deal directly with T1, WIC and 2921 etc. The following is what I get from ATT, IP masked IP Address Block IP Address: 20.20.20.136/29 WAN Link Details: WAN Link IP Address:13.13.13.92 AR Serial INT IP Address:13.13.13.93 CR Serial INT IP Address:13.13.13.94 WAN Link Subnet Mask:255.255.255.252
A: how do I configure T1, what does "AR, CR" stands for, and do I need to use both IP addresses? What is the WAN Link IP for?
B: We have two T1 lines, so I should plug them both to the WIC, say port 0 and port 1, how to configure them?
C: how do I access the firewall from the command line?
D: I followed T1/E1 HWIC installation guide, and as soon as I add channel-group to the controller t1, the serial interface went down?
i would like to configure the wireless access on the cisco 877 router either on command line or gui -also, does the wireless authentication and SSID has to be local or can i put the cisco 877 on h-reap mode and connect back to my controllers in head office and use the same SSID as in my head office ?
View 8 Replies View RelatedI have a sitecom 3G ready wireless router but does not support the local telephone company. i would like to know how to access its modem config from a command line inorder to configure the modem commands with local company settings. Its model no is WL-326v1001
View 1 Replies View RelatedI am having some difficulties on finding information on how to setup two Cisco 1252 autonomous access points, via the command line. I am not having any luck finding steps on how to go about doing this and was curious if any one would be willing to give some insight. I am working on taking two of them setting one up as the root bridge and the other as non-root.
View 3 Replies View RelatedI ran across this today on a 7200 that when all the vty lines are filled, and dont release, you enter clear line vty x and it is supposed to release the line. Well in some versions it doesn't work.
Here is the work around I found. clear tcp line vty x
I cannot eliminate the lines vty in my Cisco 7609 router when I write show users, I obtain the following thing: [code]
View 2 Replies View RelatedI have dsl and my buddy is about a mile through the fields with a couple tree lines, is there any way parabolic antennas will work for me ?
View 2 Replies View Relatedhow to clear vty line? Please see below. A sh tcp <line number> shows that the TCB is waiting for TCP Process. The TCP processs TCB is waiting for is SSH. I believe because of this ssh process still running, the vty line cannot be cleared.
sh users
Line User Host(s) Idle Location
1 vty 0 pf 10.10.20.8 9w1d 10.10.1.54
2 vty 1 pf 10.10.1.16 35w0d 10.10.1.54
3 vty 2 pf 10.10.1.16 1y14w 10.10.1.54
[code].....
I am having ACS 5.2. I have to configure a user which would have privilege 7 access and addition to this, a user can run "clear counters" command.how to configure cammand set for "clear counters"?Can i run clear counters by privilege 7?
View 2 Replies View RelatedI have ACS 5.1, I have created a user with privilege 15. I need to allow a single command by command set. I have configured command set. in command set setting i have unchecked "Permit any command that is not in the table below"
and added command as below.
Grant Command Argument
Permit clear counters
its allowing me to run clear counters, good is its not allowing to show run and configuration t commands. And problem is i can run reload command also even show interface commands.I just want to allow clear counters command only.
My grandma has a PC with Windows XP, she uses it only for Skype calls. can go in to her PC using command line from my PC? What commands should I use and what modifications to do on my grandma's PC? Should I ask permission from grandma's ISP (which is the same as mine)?
View 3 Replies View RelatedMy 3550 is always 2 characters short on the command line. So my global configuration mode will look like this:Switch3550(config Say I wanted to enabled ftp, it would look like:Switch3550(config)# ftp enab.
View 2 Replies View RelatedIm trying to get my head around my new cisco SG 300 switch. I have used the Linksys SRW range before and configured it using teraterm and method described in the link below:
[URL]
As im fimilar with this method and the commands ideally I'd like to use this on the SG 300 range as well. Failing that, is it possible to use another method which uses the same commands which can be easily copy and pasted for setting up multiple switches with the configuration?
I'm an ASDM 6.4 command line novice & I'm looking for the command to delete an unused vpn key, e.g. 'key1'.Or if there's a GUI method?
View 2 Replies View Relatedcommand to get running config of Cisco VPN 3000 concentrator.
View 3 Replies View RelatedI want to telnet a router (say) 1.1.1.1 with usename "user" and password "pass" in command line. i tried using....telnet 1.1.1.1 -l user ..........but not working
View 3 Replies View Related12 users, 3 servers, 5 smartphones/tables on the WiFi (existing AP), future VPN server (maybe 5 simultaneous inbound VPN connections at the most with at least one client using a Mac), Cisco Gigabit small business switch.Internet access, VPN connectivity, and firewall (reporting, close/open ports for custom applications as needed)I was originally going to select an ASA5505-50 user device for the above client. The device is highly regarded on the Internet, offers a command line interface, priced right for the budget and should perform all duties required by the client.However, the addition of the RV180W to the Cisco product line has me questioning my choice.
1)Does the RV180W offer a command-line interface?
2)Is the RV180W limited in the number of users it can support without having to purchase additional user licenses?
3)How are firmware/software upgrades handled with the RV180W?
4)What will the client be giving up if they choose the RV180W vs. the ASA5505?
We have lots of new lap1041 need be set static IP Adress, hostname, Controller Adress via command line, but when use command (capwap ap hostname) to set hostname , always give us command disabled, we used command:clear capwap private-config, but it does not work, why?
View 4 Replies View RelatedI want to know if WAG325N supports cisco's IOS so that i can configure it using command line interface? Is it possible?If not, how would i change ethernet interface speed setting so that it can support 100 mbps of speed. Because when i connect through LAN i'm always getting a full dulplex 10 mbps LAN connection automatically.
View 1 Replies View Relatedhow to open the Linksys E4200 command line interface? Ive tried using telnet but i get this message:Could not open connection to the host, on port 23.
View 3 Replies View Relatedhow to connect 2 personal computers with telephone line
View 1 Replies View RelatedAbout a week ago I changed over 9 HP Procurve switches that were previously stacking in series (yeah, daisy-chain) to a Access-Distribution type scenario with 2 (or 4 on server switches) Gb ports on each switch Trunked together connecting to a central full 48x Gb switch.
During this I updated firmwares on all the switches (most still on their shipped 5-8 year old versions) to the latest stable release (and in the process found out that HP switch firmware is absolutely brutal and untested - See ProCurve 2510G FW 11.16 as an example) .
I saw vast improvements across the network immediately after the change (wow, really? 9 48-port switches effectively sharing a single 1Gb line to the servers and internet was a bit slow? Don't tell my co-workers, they don't think that's possible ) .
The only thing that I didn't see an improvement in was on some Linux and BSD servers, which would top out at 11MB/s doing a SMB (SAMBA) transfer. These are managed systems part of our business system, but we still need to be able to pull local backups for ourselves. So I contacted our vendor. The vendor confirmed that the line speed is showing as 1000T-FDx (same as the switch is showing).
Vendor is now claiming that after these changes were put in place, the speed on their servers (and their servers ONLY) was reduced to a maximum of 5MB/s (~60Mb/s?) doing rsync transfers between themselves. And they are all on the same 2510 (48 port all 10/100/1000), which makes absolutely no sense whatsoever to me. Furthermore this is on the ONLY switch on the entire network that had an updated firmware already installed - that's not even a possibility here.
I put some windows servers on that switch and can get 60MB/s+ all day (SMB transfers). I've also tried from their one server that I can access to doing an rsync or scp to another BSD box, and max out at 15MB/s (with 100% CPU usage on the test box - I'm assuming the decryption is pretty heavy?)There is absolutely no QoS, limiting, or any possibility of throttling the links the servers are on the switch. There are no excessive broadcasts saturating it, and the ports and cables test fine.
I have RADIUS servers configured to authenticate administrative users and authorize them at a low level. This is working well. I also have a local level-15 user in case all of my RADIUS servers time out and someone needs to change something. This also works well. The issue I'm having is that a low-level user can log on using the RADIUS severs, then issue the "login" command and enter the local level-15 user's credentials and then operate at level 15.
I do not want the local account to work at all, except in the case that all RADIUS servers are unavailable. What I've described above works around this. How to disable the "login" command or force it to try RADIUS servers first? This is for ASA 8.2
After setting thru set time command, error message is display on server 'synthetic time issued'.
View 2 Replies View Relatedwhat i type in run box to increase INTERNET speed i saw my net provider doing this just little bit time he just type in run box ping o (.......................)/ and some numbers like IP address and then black window opened and INTERNET speed increase tell me what i type in my run box to increase speed.
View 2 Replies View Relatedthe way i find mac address remotely is by using this methodarp -a ip addressshould give you a mac address of the following ipsunil pindoria
View 2 Replies View Relatedwe just received 5 new SF200-48 Smart Switches for small business. I noticed only way I can configure them is by using the web gui. Is there a way to enable good old CLI?
View 6 Replies View RelatedI recently purchased the E3000.I thought i had read that this devices can act as an access point. There is no clear "access point" mode option so i configured it as best as i could to work with our radius server. I can connect to the wireless with radius credentials just fine but i don't get assigned a ip address from dhcp. I tried using an old blekin that does have ap mode and it works just fine.
View 1 Replies View RelatedCisco 2500 series access servers show line usage with the "show line" command:
View 2 Replies View Relatediam having two PC's which are not connected through LAN. in our office we are having a private telephone network and both the locations are connected with this telephone network (MAX) connection. Is it possible to connect the both PCs through remote desktop connection through this telephone network we are having ?. we are provided with internet conncetion for one PC.
View 2 Replies View RelatedHow do i access an MS Access backend with a front end without using SQL or share point
View 3 Replies View RelatedOn my old router I could access the line stats on the home page giving me Attenuation and SNR margin, this allowed me to keep an eye on line quality, there seems to be no equivalent info on the X2000. Is this on a hidden page like the advanced wireless page.
View 1 Replies View Related